Question about 2003 Chevrolet Silverado 1500

Open Question

How to change a power steering pump on a 2003 chevy silverado 1500

Power steering pump

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
mcgyver468
  • 710 Answers

SOURCE: where is the fuel pump shutoff switch located on a 1996 chevy silverado 1500 located

Should be on the passenger side kickplate below the glovebox and to the right. You may have to remove the plastic panel to access it or look for a small hole in it and feel around for the button

Posted on Apr 23, 2009

Ad
  • 77 Answers

SOURCE: O.B.D. FUSE 2003 CHEVY 1500

Underhood fuse box (behind battery). may be labeled cigarette lighter or "aux pwr".

Posted on Apr 29, 2009

DOODYDOODYDO
  • 105 Answers

SOURCE: process to change fuel pump on 2001 chevy silverado 1500

DROP THE FUEL TANK MAKE SURE YOU GO ABOUT HALF WAY THEN UNHOOK ALL THE LINES AND TERMINALS SO AS TO NOT DAMAGE THEM ALSO YOU NEED TO RELEASE THE FUEL PRESSURE AT FUEL RAIL BEFORE REMOVING ANY LINES

Posted on Jul 29, 2009

BeninVa
  • 389 Answers

SOURCE: Needing to replace the power steering pump on a

Disconnect the negative cable from the battery,(WARNING if you have the TheftLock Radio, make the system is off before doing anything that requires the battery to be disconnected)
Remove the radiator upper fan shroud,
Remove the serpentine belt,
Place a drain pan under the hoses to catch the fluid and remove the and remove the hoses from the hard lines coming out of the pump, making a note of which is which, stuff the end of a clean rag into each hose to prevent anything from getting inside it,
Using a pulley removal tool, remove the pulley from the pump,
Remove the four bolts from the rear of the pump( V8 has 4 bolts,V6 has 2 bolts ) and lift the pump out.
Installation,
Place the pump in it's mounting bracket and install the bolts, tighten them to 37 ft lbs.
Connect the hoses and tighten securely,
Press the pulley on the shaft using a pulley installation tool,DO NOT HAMMER IT ON,, the proper position is the front of the hub flush with the end of the shaft,
Install the serpentine belt,
Install the upper fan shroud,
Fill to the cold mark the correct of NEW fluid,
Re-connect the battery cable.
Bleed the system as follows,
Wheels straight ahead,
Start the engine and allow it to fast idle,
Check for leaks,
Re-check the fluid lever and add more if needed to keep it up to the Cold mark,
Move the steering wheel from side to side several times WITHOUT hitting the stops, this will work the air out of the system, keep adding fluid if needed during this process,
When the fluid level stops going down the system should be free of any trapped air,
Set the wheels straight ahead again and allow the engine to run for 5-10 minutes before shutting it down, re-check the fluid level,
Road test the vehicle and drive it long enough to get it up to normal operating temperature,
Re-check fluid level and fill it to the Hot level.







Posted on Dec 31, 2009

dnewcombe1
  • 1564 Answers

SOURCE: how to change my fuel pump

To begin, if you've never changed an electric fuel pump, you are safest to take it to a proffessional. The pump is located inside your fuel tank and requires dropping the fuel tank out and away from the vehicle to gain acsess. In addition there are several trick and tips, too numerous to mention about the removal of the lock ring and the pump replacement. Thank you, Dana

Posted on Feb 14, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 1998 chevy 2500.the sterling is hard to steer and the fluid is come out the cap.any idle what's going on.


Fluid Coming Out Power Steering Pump Cap - Taurus Car Club of ...

www.taurusclub.com > ... > Maintenance and Repair
Jan 9, 2010 - 2003 Vulcan has leak through cap on power steering pump. ... Hi I'm having the same thing happening to my 98 duratech. I was just getting ready to replace the rack today because of fluid coming out the drivers side boot... so decided to ... to be removed and that the bolt is recessed and difficult to reach.

Power steering issue - DodgeTalk : Dodge Car Forums, Dodge Truck ...

www.dodgetalk.com > ... > 2G Dodge RAM - General Talk
Jan 25, 2009 - Power steering issue 2G Dodge RAM - General Talk. ... Location:Sterling Heights, MI ..... pump, top off the reservior, screw on the cap, drop the truck and go drive it. .... I was able to loosen the pump and just dumped out the old fluid and.... I figured the belt was still good but the noise was definitely coming ...

Chevy Silverado Chrome Accessories - AutoAnything

www.autoanything.com/.../Chevy/.../110A50167A0A0A115A2690A1.as...
The Heartbeat has far better tastes when it comes to Chevy Silverado chrome accessories, and ... Check out our tail light chrome for Silverado rigs and you'll see what we mean. ... Chevy Silverado 2500HD Chrome Accessories .... 2012, 2011, 2010, 2009, 2008, 2007, 2006, 2005, 2004, 2003, 2002, 2001, 2000, 1999, 1998 ...

chevy bed rail caps - AutoAnything


Feb 03, 2016 | Sterling Cars & Trucks

2 Answers

Power steering went out after hearing poop in front end while in reverse with a car in tow on a tow dolly. Pump is full of fluid and not leaking and I can't see any obvious damage under vehicle. Help?!


the dealer has some recall issues with the steering shaft.
Sounds to me like the pump itself took a dump.
contact any chevy/GM dealership, ask for a service advisor and ask him if there are any recalls for your vehicle. (have VIN # handy)

Nov 03, 2013 | 2003 Chevrolet Silverado 1500

1 Answer

How to install power sterring pump


first you need to remove power steering pump drive belt and fluid using a large syringe or siphon pump.then you need place drain pan under vechicle where power steering pump located,remove power steering return line and remove power steering pressure hose using a flare nut wrench,make sure drain pan catch power steering fluid. once you have the power steering pump return hose and pressure hose remove,then remove power steering pump mounting bolts then remove power steering pump.take old power steering pump and new power steering pump to machine shop or garage so they can transfer drive pulley from old power steering pump to the new pump,once you have new power steering pump ready to install be sure to buy new pressure hose o ring if equipped, you need to bleed power steering system once you have new pump in place with every thing back in place cant give you bleeding procedure you did not tell me vechicle type you working on.

Dec 09, 2011 | Cars & Trucks

2 Answers

I need to find out how to remove the power steering pump on a 2006 pontiac grand prix 3.8L


Power Steering Pump Replacement
Removal Procedure
1. Remove the accessory drive belt.
2. Raise and support the vehicle. Refer to Vehicle Lifting.
3. Remove the tire and wheel assembly.
4. Disconnect the power steering pressure hose from the power steering pump.
5. Disconnect the power steering return hose from the power steering pump.
6. Disconnect the harness connector (4) from the power steering pump (1).
7. Remove the power steering mounting bolts from the power steering pump.
8. Remove the power steering pump from the engine.
9. Remove the power steering pump pulley from the power steering pump.
10. Remove the power steering pump reservoir from the power steering pump.
Installation Procedure
1. Install the power steering pump reservoir to the power steering pump.
2. Install the power steering pump pulley to the power steering pump.
3. Position the power steering pump to the engine.
Notice: Refer to Fastener Notice in Service Precautions.
4. Install the power steering pump mounting bolts.
Tighten the bolts to 25 Nm (18 ft. lbs.).
5. Connect the power steering pressure hose to the power steering pump.
6. Connect the power steering return hose to the power steering pump.
7. Install the harness connector (1) to the power steering pump (4).
8. Install the accessory drive belt.
9. Fill the power steering system with fluid.
10. Bleed the power steering system.
11. Operate the power steering system and inspect for power steering system leaks.

d2ff628.jpg
949e18c.jpg
a9ee201.jpg
*This originally came from abauto

Mar 24, 2011 | 2006 Pontiac Grand Prix

1 Answer

How do you remove the power steering pump from a 2001 Chev Blazer with the 4.3 engine?


4.2L Engine
  1. Remove the air cleaner assembly.
  2. Remove the drive belt.
  3. Install a drain pan under the vehicle.
  4. Disconnect the power steering pressure hose from the power steering pump.
  5. Disconnect the power steering cooler hose from the power steering pump.
  6. Disconnect the wiring harness from the wiring loom on the power steering pump.
  7. Remove the power steering pump mounting bolts.
  8. Remove the power steering pump.
  9. Remove the power steering pump pulley.
  10. Remove the power steering pump pulley using Power Steering Pump Pulley Remover tool no. J 25034-C, or equivalent.

Oct 30, 2010 | 1993 Plymouth Acclaim

1 Answer

Cant find were to put powersteering fluid


Power Steering Pump Removal & Installation 3.8L Engine To Remove:
  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Place a drain pan under the vehicle.
  3. Remove the accessory drive belt from the power steering pump pulley.
  4. Raise and safely support the vehicle.
  5. Remove the right front tire and wheel assembly.
  6. Remove the hoses from the power steering pump.
  7. Remove the mounting bolts and the power steering pump from the engine.
  8. Remove the reservoir and pulley from the pump if necessary.
To Install:
Power steering pump removal/installation (3.8L engine) gm-08-38-480.gif

  1. If removed, install the power steering pump reservoir and pulley on the power steering pump.
  2. Position the power steering pump to the engine and install the mounting bolts. Tighten the bolts to 25 lb ft (34 Nm).
  3. Install the pressure and return hoses to the pump.
  4. Install the right front tire and wheel assembly.
  5. Lower the vehicle.
  6. Install the accessory drive belt.
  7. Fill and bleed the power steering system.
  8. Inspect the system for leaks.
  9. Remove the drain pan from under the power steering pump area.
3.4L Engine To Remove:
  1. Place a drain pan under the power steering pump.
  2. Remove the coolant reservoir.
  3. Remove the pulley from the power steering pump.
  4. Remove the wiring harness near the power steering pump and place it out of the way.
  5. Disconnect the fluid hoses from the power steering pump.
  6. Remove the mounting bolts from the power steering pump and remove the pump.
To Install:
Power steering pump removal/installation (3.4L engine) 88008g71.gif

  1. Position the power steering pump assembly to the engine and install the mounting bolts. Tighten the mounting bolts to 25 lb ft (34 Nm).
  2. Install the wiring harness in its original position.
  3. Install the pulley on the power steering pump.
  4. Install the coolant reservoir.
  5. Fill and bleed the power steering system.
  6. Inspect the system for leaks.
  7. Remove the drain pan from under the power steering pump.
prev.gif next.gif

Sep 18, 2010 | 2000 Chevrolet Impala

2 Answers

Power steering pump, broken, how to replace


Power Steering Pump - REMOVAL & INSTALLATION

3.0L OHV (2 valve) Engine
(see Figures 1 and 2)

1f2a309.jpg

Fig. 1: Power steering system-3.0L OHV (2-valve)

0111341.jpg

Fig. 2: A few special tools are required to remove and install the pulley on the power steering pump
  1. Disconnect the negative battery cable.
  2. Remove the accessory drive belt.
  3. Remove the alternator.
  4. Drain and remove the radiator coolant recovery reservoir.
  5. Position a drain pan under the power steering pump underneath the vehicle. Disconnect the hydraulic pressure and return lines and allow to drain.
  6. Remove the idler pulley from the power steering pump support.
  7. Remove the bracket mounting bolt located under the belt tensioner mounting.
  8. Remove 2 retaining nuts from the bracket mounting studs. Remove both mounting studs, and pull off the power steering pump support with the pump attached.
  9. Clamp the pump support bracket in a suitable vise.
  10. Remove the power steering pump pulley from the pump shaft using Pump Pulley Remover T69L-10300-B, or equivalent. Remove the 3 bolts retaining the power steering pump to the power steering pump support and remove the power steering pump.
To install:
  1. Install the power steering pump to the power steering pump support.
  2. Install the power steering pump pulley using Steering Pump Pulley Replacer T65P-3A733-C, or equivalent; the pulley face must be flush within 0.010 inch (0.25mm) of the pump shaft.
  3. Install the power steering pump/pump support and torque nuts/bolt to 17-24 ft. lbs. (23-32 Nm).
  4. Complete the installation by reversing the removal procedure.
  5. Fill the power steering reservoir with power steering fluid.
  6. Connect the negative battery cable.
  7. Run the engine and check for leaks and proper operation. Bleed the power steering system if needed.

Hope this helps.

Sep 06, 2010 | 1996 Ford Taurus

2 Answers

Where is the power steering dipstick


Most power steering pumps are driven by the serpentine belt and should be in plain view when the hood is open.The following shows how to remove and replace the power steering pump and might give you a clue if not in plain sight. My dad's 1998 Ford Taurus has it nearly on top, but they could have changed things in the mean time: Power Steering Pump Removal & Installation Power Steering Pump (2V) To Remove:
  1. Before servicing the vehicle refer to the precautions at the beginning of this section.
  2. Disconnect the battery ground cable.
  3. Remove the accessory drive belt.
  4. Remove the alternator.
  5. Drain and remove the radiator coolant recovery reservoir.
  6. Position a drain pan under the power steering pump underneath the vehicle. Disconnect the hydraulic pressure and return lines and allow to drain.
  7. Remove the idler pulley from the power steering pump support.
  8. Remove the belt tensioner.
  9. Remove the bracket mounting bolt located under the belt tensioner mounting.
  10. Remove two retaining nuts from the bracket mounting studs. Remove both mounting studs, and pull off the power steering pump support with the pump attached.
  11. Clamp the pump support bracket in a suitable vise.
  12. Remove the power steering pump pulley from the pump shaft using Pump Pulley Remover T69L-10300-B, or equivalent. Remove the three bolts retaining the power steering pump to the power steering pump support and remove the power steering pump.
To Install:
NOTE: The pulley must be installed within 0.010 in (0.25 mm) flush with the power steering pump shaft.
Power steering pump special tools ford-08-00-401.gif

  1. Install the power steering pump to the power steering pump support. Tighten the mounting bolts to 18 ft-lb. (25 Nm).
  2. Install the power steering pump pulley using Steering Pump Pulley Replacer T65P-3A733-C, or equivalent; the pulley face must be flush within 0.010 inch (0.25mm) of the pump shaft.
  3. Install the power steering pump/pump support and torque nuts/bolt to 24 ft. lbs. (33 Nm).
  4. Install the bracket mounting bolt located under the belt tensioner mounting.
  5. Install the belt tensioner.
  6. Install the idler pulley to the power steering pump support.
  7. Connect the hydraulic pressure and return lines.
  8. Install the radiator coolant recovery reservoir.
  9. Install the alternator.
  10. Install the accessory drive belt.
  11. Fill the power steering reservoir with power steering fluid.
  12. Connect the battery ground cable.
  13. Run the engine and check for leaks and proper operation. Bleed the power steering system if needed.
Power Steering Pump (4V) and SHO To Remove:
  1. Before servicing the vehicle refer to the precautions at the beginning of this section.
  2. Disconnect the battery ground cable.
  3. Remove the accessory drive belt.
  4. Drain and remove the radiator coolant recovery reservoir.
  5. Position a drain pan under the power steering pump. Disconnect the power steering pump reservoir hose and allow it to drain.
  6. Using Pulley Remover T69L-10300-B, or equivalent, remove the pulley from the power steering pump shaft.
  7. Disconnect the pressure hose from the power steering pump and allow it to drain.
  8. Remove the power steering pump retaining bolts and the pump.
To Install:
  1. Install the power steering pump and tighten the bolts 15–22 ft. lbs. (20–30 Nm).
  2. Connect the pressure hose and secure the clamp.
  3. Using a Steering Pump Pulley Replacer T65P-3A733-C, or equivalent, install the power steering pump pulley: the pulley face must be flush with the pump shaft or within 0.010 inch (0.25mm).
  4. Connect the power steering pump reservoir hose.
  5. Install the radiator coolant recovery reservoir.
  6. Install the accessory drive belt.
  7. Fill the power steering reservoir with power steering fluid.
  8. Connect the battery ground cable.
  9. Start the engine and check for leaks and proper operation. Bleed the power steering system if needed.
prev.gif next.gif

Jul 22, 2010 | 1996 Ford Taurus

1 Answer

2003 chevy 1500 z71 hard to turn to the right. replaced power steering pump. no change.


Well try changing the steering box sounds like the steering box is messed up.

Mar 30, 2010 | Chevrolet 1500 Cars & Trucks

1 Answer

On my 20001 chevy silverado 1500 Z71 engauged 4x4 and then steering wheel got hard so hard to steer desangauged still the problem persist


Sounds like a steering pump or steering gear problem. Remove Power sterring pump cap while engine is running and see if fluid is moving. GM's are bad about PS pump shafts breaking. If no fluid movement, Replace pS pump

Mar 16, 2010 | 2000 Chevrolet Silverado

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

116 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...