Question about 1985 Nissan Sentra 2 Door

Open Question

Main bearing torque settings on e16 engine - 1985 Nissan Sentra 2 Door

Posted by Anonymous on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Autodarwin
  • 54 Answers

SOURCE: I want to know the torque tension settings for a

I would not trust anyone but the manual on this one got to your local parts store and get a Haynes or Chiltons

Posted on May 27, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Torque settings on a yaris 1.3 16v big ends,mains,flywheel,cylinderhead


Toyota Yaris Main and Big end Torque settings:
Tighten the main and big end bolts in sequential order and in two steps.
Main bearings. Stage 1.
22 ft lbs.
Stage 2.
44 ft lbs

Big end bearings.
Stage 1.
11 ft lbs.
Then Rotate bolt head a further by 90 degrees

Head bolt torque must be done in 3 steps:
1st 22 ft lbs
2nd 43 ft lbs
final 47 ft lbs
use this sequence of tightening:
9 - 3 -1 -6 -8
7 - 5 - 2 -4 - 10

Flywheel spec:
65 ft lbs

Jul 15, 2016 | 2007 Toyota Yaris

1 Answer

I want to know what the torque specififcation is


Torque settings vary from engine to engine try googling torque settings for your particular vehicle

Sep 18, 2014 | Cars & Trucks

1 Answer

Torque settings on cranck sharf bearings


Torque settings for V-6 engine.
Main bearing cap bolts torque:
Torque: 27 N·m (275 kgf·cm, 20 ft·lbf)
Mark the front of the main bearing cap bolt with paint.
Re tighten the main bearing cap bolts by 90 degrees.
Check that the crankshaft turns smoothly.

Connecting rod cap bolts torque:
Torque: 24.5 N·m (250 kgf·cm, 18 ft·lbf)
Mark the front of the main bearing cap bolt with paint.
Re tighten the main bearing cap bolts by 90 degrees.
Check that the crankshaft turns smoothly.

Feb 11, 2014 | Toyota Land Cruiser Cars & Trucks

1 Answer

Hi im fixing a 89 honda civic have everything to put it back together but the torque settings for mains,connector rod bearings head stage 1,2,3 an the rest thanks


CRANK SHAFT PULLEY BOLT TORQUE IS 83 FT LBS. MAIN BEARINGS TORQUE IS 48 FT LBS ROD BEARINGS TORQUE 23 FT LBS. YOU NEED A BEARING SEQUENCE GET PIECE OF PAPER WRITE NUMBERS 9 5 1 3 7 AND UNDER THIS NUMBER LINE NUMBERS UP ON EACH OTHER WRITE DOWN NUMBERS 8 6 2 4 10 YOU HAVE 10 CRANKSHAFT MAIN BEARING BOLTS. WHEN YOU LINE UP BOTH NUMBERS YOU WILL START TIGHTEN BOLTS 1 AND 2 TIGHTEN BOLTS 3 AND 4 TIGHTEN BOLTS 5 AND 6 TIGHTEN BOLTS 7 AND 8 TIGHTEN BOLTS 9 AND 10 YOU ARE TIGHTEN BOLTS IN A CRISS CROSS PATTERN. BESURE TO POUR OIL OR LUBRICATE CRANKSHAFT AND BEARINGS WITH CLEAN ENGINE OIL.WHEN YOU TORQUE MAIN BEARINGS TORQUE ALL THEM TO 20 FT LBS AND SECOND PASS TORQUE ALL BOLTS TO FINAL TORQUE 48 FT LBS. IF YOU RUN TO ANY PROBLEMS. YOU CAN BUY A HAYNES REPAIR MANUAL IT CAN HELP YOU.

Mar 02, 2011 | 1989 Honda Civic

1 Answer

Does anyone know the crank main bearing nut torque Alfa V6 3l


Torque to 25Nm, then tighten through a further 79 degrees. You need an angle gauge to do it properly.

Jan 29, 2010 | 1986 Alfa Romeo GTV6

2 Answers

WOULD YOU KNOW THE TORQUE SETTINGS FOR MAIN BEARING AND BIG END BEARING CAPS FOR ISUZU 4JG2 ENGINE


Mains Stage 1 83nm
Mains Stage 2 167nm

Big ends Stage 1 29nm
Big ends Stage 2 45 - 60 degrees

Hope this helps

Jul 10, 2009 | 1994 Isuzu Trooper

1 Answer

Rod and main bolt torque specs


rods bearings for the 4.2 engine is.18 ft lbs +110 degrees. main bearings 18 ft lbs +180 degrees. the 5.3 engine rod bearings torque is.15 ft lbs +85 degrees.main bearings is inner bolts 1st pass 15 ft lbs .final pass is 80 degrees.outer bolts 1st pass is15 ft lbs .final pass is additional 51 degrees.the m8 bolts 18 ft lbs..the 6.0 engine rod bearings torque is 15 ft lbs plus 85 degrees.the main bearings torque is inner bolt 1st pass 15 ft lbs .final pass plus 80 degrees. outer bolts .1st pass 15 ft lbs final pass plus 51 degrees.m8 bolts 18 ft lbs.

Jun 19, 2009 | Saab 9 7X Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

89 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...