Question about Jeep Cars & Trucks

1 Answer

How do I replace the flasher hazard switch in a 2006 Jeep Liberty?

Posted by on

  • Tazmaniac Feb 08, 2012

    Thank you Roger, I was referring to the combination switch above the radio on the dash. What is the "multifunctional switch" you refer to? Turn signal lever?

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Greenhorn:

    A rookie expert who has answered 20 questions on their first day.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 29 Answers

You are going to have to have access to torx bits and torx screwdrivers before you start. But since you are not used to working in these areas I recommend disconnecting the battery before starting. Then you must remove the trim shroud around the steering column and then you have access to the multifunction switch. It then can be unbolted from housing and the wiring disconnected. Replace with new switch and put back together in reverse order.
Hope this helps
Roger

Posted on Feb 08, 2012

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: 2002 Workhorse chassis RV hazard flasher doesn't work

I am looking for a locking gas cap for my 2005 Bounder 36Z. This motorhome has a Workhorse chassis. Can you help me locate the part number and a dealer near Newberg, Oregon?

Thank you.

Sharon Bladow
503 554-1281

Posted on Aug 15, 2008

  • 137 Answers

SOURCE: Inoperable Power Window 2006 Jeep Liberty

the window regulator needs to be replaced

Posted on Jan 19, 2009

Mikey108
  • 475 Answers

SOURCE: i have a 2006 jeep liberty and three lights are staying lit and

You need to take the jeep to a dealer or a good mechanic who can retreive the codes out of the computer. You may have a module problem but I will not guess without knowing the codes.

Posted on Feb 11, 2009

  • 98 Answers

SOURCE: I can not find the flasher relay on my 2006 jeep wranger?

remove shroud around signal and wiper switch,and it is between them

Posted on Aug 03, 2009

  • 454 Answers

SOURCE: replaced starter 2006 jeep liberty still won't

Check that you have power at the main post of the starter. Then check the solenoid activation circuit from the ignition switch.

Posted on Oct 04, 2009

Testimonial: "have power at post on starter-could it be safety neutral switch on transmission?"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where is the turn signal flasher relay located on a 2002 liberty


It is built into the hazard switch. If the hazard switch is on the steering column, replace the turn signal switch. If it is in the dash, replace just the hazard switch.

Dec 18, 2014 | 2002 Jeep Liberty

2 Answers

What would cause my blinkers to stop working on a 2000 jeep cherokee sport?


Interesting, these are on the same circuit.

1) Click the hazards on and off a few times to exercise the switch.
2) Replace the flasher timer relay.
3) I believe that this system has a little computer center, about the size of a machbox and it is located under the dash. Swap this out with one from a junkyard.

May 22, 2014 | 2000 Jeep Cherokee

1 Answer

Replace Flasher Relay for 2006 Jeep Liberty


how to, , who can, where to buy? where is.???
why not ask a real question, and not use statement forms???

does both turns sigs and hazzard both fail?
all lamps dead, ? all stuck on, all flashing to fast.
all fuse good?
lost the owners manual ? in glove box , bingo....
http://justgivemethedamnmanual.com/jeep/jeep-liberty-owners-manuals/
gas car? not diesel.
page 349? fuse 11 good, flasher fuse?
fuse 39 is also flasher.

06 liberty GAS engine., size unknown
USA , not export.'
answers from FSM.
THERE IS NO RELAY, SORRY !
the combo head switch does IT ALL.
and is in side the SCM, the steering control module.
the fsm covers the replacment.
but do post symptoms and not guess.
why guess.

do the hazards work.?

Feb 15, 2014 | 2006 Jeep Liberty

1 Answer

Jeep liberty flasher


you have a rear shorted wire to your blinker..take the gels off and check your connections!

Jan 08, 2014 | Cars & Trucks

1 Answer

Flasher unit relay


Hi there:The combination flasher for this model is integral to the hazard switch located in the center of the instrument panel, just above the radio. The combination flasher is a smart relay that functions as both the turn signal system and the hazard warning system flasher. If supplemental lighting is added to the turn signal lamp circuits, such as when towing a trailer with lights, the combination flasher will automatically try to compensate to keep the flash rate the same.


The combination flasher cannot be repaired or adjusted and, if faulty or damaged, the hazard switch unit must be replaced.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

May 12, 2012 | 2003 Jeep Liberty

1 Answer

Were is the flasher for left rear light


There is one flasher that controls all 4 turn signals. If only one light is not flashing the flasher relay is not the problem. If the flasher relay is bad none of them will flash. Check the bulb. The Turn signal flasher relay is located front seating area. It is integral to the hazard switch located in the center of the instrument panel, just above the radio. Curtorsey: Auto Zone

May 18, 2010 | 2002 Jeep Liberty

1 Answer

Jeep 2006: Blower only works on High


since blower only works on high, I would only replace the resistor. 99.9% of the time this is the problem.

Apr 20, 2010 | 2006 Jeep Liberty

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

462 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...