Question about Hyundai Cars & Trucks

1 Answer

I need instructions to program keyless entry remote for 2002 Hundai Santa Fe

Keyless entry remote programming instructions for 2002 Hundai Santa Fe. Hundai Dealer is charging $200. Please help.

Posted by on

  • Chandler Feb 08, 2012

    Thank you. I cannot locate the memory switch.

  • C Levang Feb 14, 2013

    please let me know if you find it because I can't seem to locate it either!

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 8 Answers

For a 1994 to 2006 Sonata, a 2001 to 2006 Elantra, a 2000 to 2006 XG350 or a 2001 to 2006 Santa Fe, you will need to access alarm system control module. On most of those vehicles it is located on the driver's side fascia panel. But on the Sonata, the facia panel is in the center.


  • 2 Once you have found this module, you will want to ensure that the memory switch is in the OFF position. Then turn the ignition on.
  • 3 Wait 5 seconds and set the memory switch to SET position and then press the remote transmitter lock button to send the code to the alarm system control module.
  • 4 If you would like to program a second remote transmitter then you will need to press second remote transmitter lock button.
  • 5 Next set the memory switch to off, then turn the ignition off. You can confirm your programming by locking and unlocking the vehicle with both of the remotes. good luck my friend
  • Posted on Feb 08, 2012

    6 Suggested Answers

    6ya6ya
    • 2 Answers

    SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

    Hi,
    a 6ya expert can help you resolve that issue over the phone in a minute or two.
    best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
    the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
    click here to download the app (for users in the US for now) and get all the help you need.
    goodluck!

    Posted on Jan 02, 2017

    • 2 Answers

    SOURCE: How to program keyless remote

    I just had to buy one too and these are the instructions I was given by the guy I bought it from. I haven't tried them yet. Hopefully they work for us both :).

    1.Find the ETACS unit under the steering wheel first,there is a small switch onit.
    2.Once the switch is located make sure your key is not in the ignition and set the switch from off to set.
    3.Press keyfobs door lock button for one second, this sends the codes to the ETACS and stores it.
    4.Do the same thing if you have 2 remotes for the vehile.
    5.Now set the ETACS switch from set to off.
    6.Remotes should now be programed.

    Posted on Jan 19, 2009

    • 91 Answers

    SOURCE: program keyless entry for mazda rx8

    its a dealership and computer job by them, you cant do it yourself

    Posted on Jul 25, 2009

    SOURCE: nissan murano 2005 sl keyless entry remote programing

    Close all vehicle doors, LOCK doors using drivers side switch.

    Insert key all the way into the ignition, (do not turn) remove key.

    Repeat this step 5 times. (6 total)

    Hazards should flash to indicate program mode.

    Press any button on transmitter to be programmed, hazards should flash to indicate successfull program.

    *For additional remotes, cycle drivers door lock UNLOCK, LOCK, press any button on remote, hazards should flash. Repeat step as necessary.

    Ignition ON, (engine off) ignition OFF, UNLOCK using drivers side switch, test remotes.

    Source

    Posted on Aug 06, 2008

    emissionwiz
    • 75235 Answers

    SOURCE: programing keyless entry

    If you have an owners manual the programming instructions are in there. If no manual here they are:

    1. Turn the ignition off.
    2. Ground the receiver program terminal. Jump the two terminals located in the programing ground connector. (What this means in simple terms is locate the wires that run on the right side of the trunk. There is two black wires that has a plug on the end with two prongs. It is in between the antenna and tail lights.)
    3. Within 2 seconds of connecting the prongs the door locks will lock. The unlock and the rear compartment lid release will produce a cycle, causing the horn to chirp. This indicates that the module is ready for reprogramming.
    4. Press and hold the lock and unlock buttons at the same time until the doors lock and unlock. The rear compartment lid will release and the horn sounds to indicate that the transmitter has successfully been reprogrammed. (Hold buttons down for approximately 12 seconds)
    5. Repeat the previous step for the remaining transmitters.
    6. Remove the jumper at the program connector.
    7. Verify the proper operation of each transmitter

    Posted on Sep 30, 2008

    Molson02536
    • 3854 Answers

    SOURCE: programming a keyless entry remote

    Key Fob Auto Learn
    This procedure will first erase all known key fobs. The procedure will then program a single or multiple key fobs. Method 3 is a series of three 10-minute key cycles, for a total of 30 minutes. This procedure requires that you have a replacement key fob and the vehicle mechanical key.

    Important: All previously programmed key fobs will be erased upon completion of the 30-minute programming procedure. The order in which the key fobs are programmed will determine its numbering position within the RCDLR memory. The first key fob programmed will be key fob #1, and the second key fob programmed will be key fob #2. The number stamped on the key fob case is for reference only: #2 can be programmed as #1.
    Do not place any known good key fobs in the vicinity of the vehicle when programming. 

    The vehicle must be OFF. 
    Place the replacement key fob in the console pocket with the buttons facing forward. 
    Insert the vehicle key in the driver door lock cylinder located in the driver door handle and cycle the key 5 times within 5 seconds. 

    The DIC will display a message: OFF/ACC TO LEARN. 
    Press the OFF/ACC portion of the ignition button. 
    The DIC will display a message: WAIT 10 MINUTES, then it will count down from 10 to 0, one minute at a time. 
    When the counter reaches 0, DIC will display OFF/ACC TO LEARN. 
    Repeat steps 5-7 two more times, for a total of 30 minutes. 
    The DIC will display a message: OFF/ACC TO LEARN. 
    Press the OFF/ACC portion of the ignition button. 
    A beep will occur and the DIC will display: READY FOR FOB 1. At this time all previously known key fobs have been erased. When fob 1 is programmed a beep will be heard and the DIC will display a message: READY FOR FOB 2. 
    Additional key fobs can be programmed by taking fob 1 out of the pocket and inserting fob 2. If desired, up to 4 fobs can be programmed. Once 4 fobs have been learned, the DIC will display a message: MAX FOBS LEARNED, and automatically exit the program mode. 
    If learning less than 4 key fobs, press the OFF/ACC portion of the ignition button to exit the program mode. 
    Operate the active portion of each key fob in order to finalize the programming sequence and verify correct system operation. 

    Good luck and hope this help's keep me posted, there are 3 other methods and the 5th method is a tech 2 scan tool that the dealer uses but this should work on your year of cadillac. 

    Posted on Jul 01, 2009

    Add Your Answer

    Uploading: 0%

    my-video-file.mp4

    Complete. Click "Add" to insert your video. Add

    ×

    Loading...
    Loading...

    Related Questions:

    1 Answer

    How do I reprogram the key fob on my 2005 Hyundai Santa Fe without having to pay the fee at the dealership?


    Well, you basically have only 3 choices:
    1. Pay the fee at the dealership
    2. Purchase the high-dollar equipment that is required to perform the programming procedure
    3. Forget about adding another key fob to tor vehicle.

    TECHNICAL SERVICE BULLETIN

    Group
    90 - ELECTRICAL

    Number
    03-90-020

    Date
    October, 2003

    Model
    Elantra 2001-2004, Santa Fe 2001-2004, Sonata 2002-2004, Tiburon 2003-2004, XG(NNN) NNN-NNNNand XG(NNN) NNN-NNNN2004

    Subject
    SECURITY SYSTEM KEYLESS ADAPTER CABLE

    This bulletin supersedes TSB # XXXXX
    DESCRIPTION:
    The security system keyless adapter cable (SPX/Kent-Moore P/N 09900-21300) is a special service tool (SST) that is used for programming new keyless entry remote transmitters to the factory security systems. The keyless adapter is used in conjunction with the Hi-Scan Pro (with Hi-Scan SOL Pro Software Version 09-29-03 or newer) and Data Link Connector (DLC) Cable.
    SERVICE INFORMATION:
    The keyless adapter cable can be used on the following vehicles:
    ^ 2001 -2004 Elantra
    ^ 2001-2004 SantaFe
    ^ 2002 - 2004 Sonata


    Apr 24, 2011 | 2005 Hyundai Santa Fe

    1 Answer

    I have a 96 ford conversion van with a 600 plus addon keyless system and need to program new keyless remots , need to know how to get system in program mode.


    Hi.

    To program ( or reprogram ) a keyless entry remote transmitter into the remote keyless entry module, perform the following steps:

    1. Turn the key to ON or ACC and short the two terminals of the program connector, a two-pin connector located below the driver's side of the instrument panel at the base of the steering column. All doors should lock and then unlock.
    2. Press any button on each keyless entry remote transmitter in turn. All doors should lock and then unlock. If the door locks do not respond, press the button again (up to three times maximum with the same keyless entry remote transmitter). If the door locks still fail to respond, go to Pinpoint Test A.
    3. Repeat Step 2 to program additional keyless entry remote transmitters into the remote keyless entry module (up to four keyless entry remote transmitters maximum).
    4. Turn key off.
    5. Remove the short from the program connector. All doors should lock and then unlock.
    6. Verify that the keyless entry remote transmitters have been successfully programmed by pressing the LOCK or UNLOCK button on each one, and observing that the system responds by locking and/or unlocking the doors.


    I hope this helps you.

    Thanks!

    Nov 28, 2010 | 1996 Ford Econoline

    1 Answer

    Keyless remotes not working


    Try reprogramming the remotes. Here are the instructions for the procedure. Hope it helps. Cobra!
    Programming NOTE: All keyless entry remote transmitters (15K601) must be programmed at the same time.
    NOTE: To program (or reprogram) the keyless entry remote transmitters into the RAP module, perform the following steps:
    1. Make sure that the anti-theft system is not armed or triggered.
    1. Turn the ignition switch (11572) from OFF to RUN eight times within ten seconds, ending in RUN. If the RAP module has successfully entered program mode, it will lock and then unlock all doors.
    1. Within 20 seconds, press any button on a keyless entry remote transmitter, and the doors will lock and then unlock to confirm that each keyless entry remote transmitter has been programmed. Repeat this step for each transmitter.
    1. If the door locks do not respond for any keyless entry remote transmitter, wait several seconds and press the button again. If the door locks still fail to respond, refer to Inspection and Verification.
    1. Turn the ignition switch to the OFF position, or wait up to 20 seconds after step 2, to exit program mode. If a keyless entry remote transmitter has been programmed (or reprogrammed), the RAP module will lock and unlock all doors one last time to confirm.

    Jun 06, 2010 | 1998 Ford F150 Regular Cab

    3 Answers

    How to program 2004 Hyundai Santa Fe Keyless Entry Remote


    Synchronization
    When
    System malfunction. Remote control added or replaced.
    How
    Access alarm system control module located under driver's side lower fascia Fig. 2 . Set memory switch to SET position. Press remote control lock or unlock button. Set memory switch to OFF position. Confirm synchronization has been successful by locking and unlocking vehicle. Repeat procedure for second remote control. Synchronization can also be carried out using diagnostic equipment.
    NOTE: A maximum of 2 remote controls can be programmed. NOTE: If remote control fails, system can be deactivated as detailed in the owner's handbook.

    Mar 23, 2010 | 2004 Hyundai Santa Fe

    1 Answer

    2002 Hyundai Santa Fe- which replacement battery do I need for the keyless entry remote (CA2032 or what)?


    dear friend-the battery for your remote can be found at any pharmacy.it is the right number.

    Jul 07, 2009 | 2002 Hyundai Santa Fe

    1 Answer

    PROGRAM KEYFOB FOR HYUNDAI SANTA FE


    This is from the factory service manual of your car:
    There is no onboard programming procedure for this vehicle. This vehicle requires special equipment be connected to the vehicle to program the keyless remote. Translation you need the dealer to do this.

    May 22, 2009 | 2005 Hyundai Santa Fe

    2 Answers

    Program factory remote keyless entry: 2003 Hyundai XG350


    The procedures you list require the Hyundai Keyless Remote programming module, which you don't have. This module is proprietary - only Hyundai Dealerships have it. There is a 10 pin connector under the dash (next to the DLC - Data Link Connector) which is used to connect the Keyless Remote Programming Module. This module has two switch positions "Ready" and "SAVE". When the switch is place in the 'SAVE" position, that's when the keyless remotes are activated to send their 'codes' to the Electronic Time and Control System (ETACS). The module's switch is then set to "Ready" and the remote is tested to see if it works properly.

    May 22, 2009 | Hyundai Motor 2003 XG350

    1 Answer

    Program factory remote keyless entry for 2003 Hyundai XG350


    This bulletin supersedes TSB# 02-90-001.
    DESCRIPTION: The security system keyless adapter cable (SPX/Kent-Moore P/N 09900-21300) is a special service tool (SST) that is used for programming new keyless entry remote transmitters to the factory security systems. The keyless adapter is used in conjunction with the Hi-Scan Pro (with Hi-Scan SOL Pro Software Version 09-29-03
    or newer) and Data Link Connector (DLC) Cable. SERVICE INFORMATION: The keyless adapter cable can be used on the following vehicles:
    • 2001 - 2004 MY Elantra
    • 2001 - 2004 MY Santa Fe
    • 2002 - 2004 MY Sonata
    • 2001 - 2004 MY XG300/350 0390020a.gif
    NOTE
    • The 2003 - 2004 MY Tiburon does not need the Keyless Adapter Cable to add keyless entry remotes to the factory security system. Instead, the Hi-Scan Pro connects to the vehicle using only the DLC cable. See page BE-60 in the 2004 MY Tiburon Shop Manual for the latest instructions.
    • The most current Keyless Adapter Cable Instructions are available in the following shop manuals:
    SHOP MANUAL

    PAGES

    2004 MY Elantra
    BE-73 - BE-74
    2004 MY Santa Fe
    BE-43 - BE-44
    2004 MY Sonata
    BE-40 - BE-41
    2004 MY XG350
    BE-46 - BE-47
    KEYLESS ADAPTER CABLE INSTRUCTIONS:
    1. Connect the keyless adapter cable to the Hi-Scan Pro DLC cable. 0390020b.gif
    2. Plug the keyless adapter into the vehicle's 10-pin multi-purpose connector located behind the driver's side lower instrument panel (next to the DLC). NOTE Sample vehicle shown is the Santa Fe.
      0390020c.gif
    3. Turn the Hi-Scan Pro ON
      and press ENTER
      . NOTE "Release date 29. Sep. 2003" OR LATER
      must appear on this screen. To update your SOL card with the latest software go to www.hmaservice.com and refer to TSB 00-00-001.
      0390020d.gif
    4. Select option "HYUNDAI VEHICLE DIAGNOSIS"
      and press ENTER
      . 0390020e.gif
    5. Select vehicle model and press ENTER
      . 0390020f.gif
    6. Select option "TRANSMITTER CODE SAVING"
      and press ENTER
      . 0390020g.gif
    7. Ensure that the key has been removed from the ignition cylinder before proceeding. 0390020h.gif
    8. Follow the steps noted on the Hi-Scan Pro screen to program the remote(s). NOTE The factory security system can only be programmed to accept two remote transmitters and MUST be programmed for both remote transmitters at the same time.
      0390020i.gif
    9. Press ESC
      on the Hi-Scan Pro and verify that the remote(s) are functioning properly.
    10. Turn the Hi-Scan Pro OFF
      and disconnect the adapter cable from the multi-purpose connector.

    May 22, 2009 | Hyundai Motor 2003 XG350

    1 Answer

    How to program keyless remote


    I just had to buy one too and these are the instructions I was given by the guy I bought it from. I haven't tried them yet. Hopefully they work for us both :).

    1.Find the ETACS unit under the steering wheel first,there is a small switch onit.
    2.Once the switch is located make sure your key is not in the ignition and set the switch from off to set.
    3.Press keyfobs door lock button for one second, this sends the codes to the ETACS and stores it.
    4.Do the same thing if you have 2 remotes for the vehile.
    5.Now set the ETACS switch from set to off.
    6.Remotes should now be programed.

    Jan 10, 2009 | 2007 Hyundai Santa Fe Limited

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    2,072 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Hyundai Experts

    yadayada
    yadayada

    Level 3 Expert

    75197 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22095 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    7782 Answers

    Are you a Hyundai Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...