Question about Chevrolet Impala

1 Answer

2008 Chevy Impala SS V8 , is making grinding noise during left turn and acelerating. Thought it was left hub bearing and had fix noise is still there. Any ideas?

Posted by on

  • Patrick Feb 09, 2012

    Decided today to try something put car in 1 on shifter and it grinder the whole time while driving.

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 54 Answers

Sounds like something in the driveline. if wheel bearings are good it could be brake caliper making contact with rotor, axle bearings , or the transmission may be failing. if it does it worse in 1st gear then its more likely to be a transmission problem. check both sides though. often noise and vibration can travel from one side to the other. also check your tires for knots or cuts, flat spots or heavy brake dust on the wheel. tell me what you find. hope this helps.

Posted on Feb 10, 2012

  • Michael Youssef Sep 06, 2012

    Hi I have athe same car ( chevy Impala SS with 48300 miles on it) I get this weird grinding noise ( i wanna say ) but it only happens when im decelerating. I tried putting the car in neutral before I slow down and the noise does not happen. Any ideas??? Thank you

×

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

losflip
  • 94 Answers

SOURCE: 2001 monte carlo ss. Rear wheel bearings making a grinding noise

It is pretty easy, there is not much labor involved if it has anti-lock brakes in the rear you will also have to un-plug the wire harness attached to hubs.

Posted on Nov 26, 2008

  • 28 Answers

SOURCE: 2001 2wd, v6 tracker LT, 110K miles; Grinding, clunking nosie

If it sounds like a rumble from back wheels it may be the rear end going out. Mine has been replaced twice with used rear end. You should be able to confirm it by looking at the rear tires both sides of tire for an oil leak or wet spot on tire or rim.

Posted on Mar 30, 2009

  • 3 Answers

SOURCE: 2001 GMC Jimmy - Wheel bearings

if u have to replace the whole hub asym it will come all togather.. or as a set of bearings that just sit in the hub.

Posted on Apr 03, 2009

Molson02536
  • 3854 Answers

SOURCE: 01 impala can a bad front hub bearing cause the

Yes it can if the hub has lot's of play but you will have drive issues first. Check the ABS sensor for broken wire, dirt, and the gap to the speed ring on the hub. You can clean the the ABS sensor with brake parts cleaner with out removing it, just a good spray should to the trick and check the gap from the sensor to the speed ring. You can use a dime as a reference for the gap to make sure you have the right gap and make sure the ABS wire harness is not damages in any way. Good luck and hope this helps, also check the fuse to the ABS system. If there is a Auto Zone have the can scanned since it's fee of charge just to make sure it's not the ABS module that has gone bad.

Posted on Jul 01, 2009

  • 58 Answers

SOURCE: how do you remove the old car battery on a 2008

  1. Disconnect the negative battery cable.
  2. Remove the right front diagonal brace. The brace goes from the rad support to the fender area.Three bolts need to be removed.
  3. Reposition the positive battery cable terminal cover (1).A red cover over the positive cable at the battery.It pops off.You may need a screw driver to pop it off.
  4. Loosen the positive battery cable terminal nut.
  5. Remove the positive battery cable terminal from the battery.
  6. Reposition the underhood accessory wiring junction block.See steps 9-14.
  7. Remove the battery retainer bolts (1) and retainer (2).
  8. With the aid of an assistant, remove the battery.
  9. Remove the electrical center cover (1).
  10. Disconnect the positive battery cable from junction box
  11. Remove the fasteners (1) securing the electrical center board (2).
  12. Unlock the tabs on the electrical center board.
  13. Lift up on the electrical center board.
  14. Remove the fasteners (1) securing the electrical center bracket (2) to vehicle.

Posted on Nov 01, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

05 chevy equinox makes grinding noise when I turn left.


Cv shaft is bad, ( drive shaft from Trans to wheel. )

Jan 28, 2014 | Cars & Trucks

1 Answer

2008 Jeep Patriot. Engine makes rattling/grinding noise near right wheel well when making a right turn. This problem started when the weather hit about 20 degrees.


sounds like a wheel bearing,one piece hub and bearing,not a hard fix ,bearing is like 100 bucks tho. Don't let it get worse,the wheel could lock up

Dec 10, 2013 | Cars & Trucks

1 Answer

Undue pressure on the hub bearings on a 1997 Cavalier


ok so I have a 97 chevy Cavaliar convertable. And when I first got it, it was making a grinding sound when ever I drove it. the sound seemed to be coming from the passanger front tire and when I would turn right the sound was still there but when I turned left the sound would go away during the turn. Well naturally I thought the bearing was going out on the side. so I bought a new one it came pre lubed and put together, in the box was also a spacer it just looked like a metal disc. well when I went to put the new bearing on the car who ever had done so previously had left the spacer off. i wasn't sure were that spacer went but I tried putting on the front and it fit so i just finished and put it back together. to my surprise the grinding was still there. after many surfing and calling around I discovered that the spacer was ment to go behind not infront once I changed that and yes it was a pain in the *** i put the car back together and car was like new. hope that helps

May 25, 2012 | 1997 Chevrolet Cavalier

1 Answer

Abs light on, traction light off and grinding


could be a warn front hub bearing. this is real common . new hub should come with the abs
wheel speed sensor. jack up car and safely
support , rotate tires and listen for noise ,
also attempt to wigggle/ move wheels and
see if any play

Nov 22, 2009 | 2003 Chevrolet Impala

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

703 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...