Question about Cars & Trucks

Open Question

Need a chicago electric hoist 44006 manual - Cars & Trucks

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to take an motor out of an 1976 Minnie


You need to take off the bumper and the door that covers engine access. You'll need a low boy engine hoist. Take out the radiator and push aside the AC condenser and oil cooler. Take off the fan blades from the watre pump pulley. Find a good place to hook up the chain on the hoist. Now go under the engine and remove the access cover on the bell housing. Take out the bolts that hold the torque converter to the flywheel. Now go after the bolts that hold the transmission to the engine. Put a floor jack under the transmission so it wont drop when you jack up the engine with the hoist. After you remove all the electrical wiring from the components on the engine remove the bolts on the motor mounts and raise the engine with the hoist . Pull the engine out while looking for anything that you didn't disconnect. Be sure the transmission doesn't drop when the engine separates from it.

Sep 30, 2014 | Cars & Trucks

1 Answer

Easiest way to remove the motor out of a 3.8 2007 grand Prix


Have someone else do it :)
Seriously, if you're referring to the ENGINE, you will need a hoist, lots of patience, a shop manual to guide you, lots of tools, and several hours.
If you are referring to a WINDOW MOTOR (ENGINES are powered by fuel and MOTORS are electric), it's an easier task, requiring only a few tools and removal of the door panel(s).

Jul 22, 2014 | Cars & Trucks

1 Answer

Electrical motor demag pk10n-f wiring diagram


I have searching this blog and found here an interesting post about this Electric Motor demag, but i have no idea for that, you can find them on the web, there are many websites will help you for regarding your issues.

demag

Aug 14, 2012 | Cars & Trucks

1 Answer

Need to swap engines in a 99 toyota solara 2.2 with auto. What is most efficient way to get engine out? Does it require trans removal? Do I go up or down with engine. Don't have manual but owned a shop for...


First drain all fluids, remove all wiring, hoses, tie rod ends, controll arms, shafts, i recommend removing the transmission but you dont have to it just makes things easier. after all electrical and hardware has been disconnected from the engine you can put your engine hoist under the motor snug and remove the motor mounts, pull the motor out and your done. good luck

Jan 28, 2011 | 1999 Toyota Camry Solara

1 Answer

Donde esta el termostato del 300 1999 chrysler


3.2L & 3.5L Engines
  1. Disconnect negative cable
  2. Drain cooling system.
  3. Raise vehicle on hoist.
  4. Disconnect electrical connectors from engine oil and power steering pressure switches.
  5. Disconnect radiator and heater hoses from thermostat housing.
  6. Remove thermostat housing bolts.
  7. Remove housing, thermostat, and gasket.

To install:

  1. Position gasket on thermostat and housing.
  2. Install thermostat housing, gasket and mounting bolts onto block. Tighten attaching bolts to 105 inch lbs. (12 Nm).
  3. Install radiator hose.
  4. Install bypass hose.
  5. Connect electrical connectors from engine oil and power steering pressure switches.
  6. Connect negative cable.
  7. Fill cooling system.
  8. Inspect for leaks.
  9. Lower vehicle on hoist.

Jan 23, 2011 | 1999 Chrysler 300M

1 Answer

The cable for the spare tire on my 2006 1500 works fine (it's all the way down) but the retainer did not lower at all so I cannot pick up the spare tire. Can anyone help? Thanks


  1. Rotate the hoist shaft counterclockwise until approximately 15 cm (6 in) of cable (1) is exposed.
  2. While holding the latch pin (3), fully depress the latch button (2) and release the secondary latch from the hoist assembly. Some side-to-side and/or up-and-down movement may be necessary to disengage the latch mechanism.
  3. Continue rotating the hoist shaft counterclockwise in order to lower the hoist the rest of the way.
  4. If this does not release the secondary latch, the spare tire hoist will need to be replaced. See the following procedure.
Important: If the spare tire hoist has been fully raised without a spare tire in place, the secondary latch mechanism may have become engaged. If this has occurred the hoist will not lower and the following steps will need to be followed:

Nov 01, 2009 | 2005 Chevrolet Silverado

1 Answer

How do I get a manual for a 1998 mercury Sable for free?


To replace or service the transmission you will need to:

lift the vehicle
support then engine using a hoist/lift
support the transmission using a hoist/lift
unbolt the motor mounts (There are 4 of them)
lower the engine 8 - 10 inches
unbolt the transmission
lower the transmission

Jul 19, 2008 | 1998 Mercury Sable

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

130 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...