Question about Nissan Maxima
Posted by Anonymous on
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
bank 1 refers to the side of the engine that #1 cylinder is on , and sensor 2 refers to downstream , after the catalytic converter. , this link shows bank 1 on a 2001 nissan maxima V6 being on the firewall side . if you had a 4 cylinder it would be downstream after the catalytic converter .
Posted on Jan 04, 2009
You need to remove all of the air intake and other things behind the battery. The start motor is held in with two bolts. You might need a breaker bar to break loose the one bold as I did. Once you remove all of the air intake equipment. This will help you gain access to the starter motor. You might not need to remove all the air intake equipment I know it made it alot easier for me to remove the starter and I took it to the auto store and had it tested.
Posted on Apr 07, 2009
SOURCE: 1996 Nissan Maxima oxygen sensor
hye there ,,there are 3 o2 sensors on your car,,one for each bank,,,and the 3rd sensor is located after the cat this one usually goes first,,,,just make sure you no if your cars an import or not as they can be different,,,then you should be safe when ordering ,,hope that helps,,,
Posted on Apr 24, 2009
Hi, this is a common issue within car CD changers. the load motor go through lots of trauma during the life span that i usually 3 to 5 years. the load motor operates everything in the changer. it works the load tray and spinning of the disc as well. when this motor is out, the changer will be rendered useless. replacing the load motor will fix this issue or, you can just purchase a new changer and save a lot of money.
Posted on May 21, 2009
WHEN YOU STAND ON THE FRONT OF THE CAR YOU ONE IS RIGHT BELOW OF THE INTAKE WHICH IS BANK 2 OR THE ONE CLOSE TO FIREWALL , BANK 1 ONE IS ON SAME SIDE NEXT TO THE RADIATOR BUT THEY BOTH ON THE CAM RIGHT SIDE OF THE ENGINE, THE EASIEST WAY TO IDENTIFY THEM IS THAT THEIR CONNECTOR IS GREEN, ONCE YOU LOCATE THEM THE CLIP NEEDS TO BE PUSHED DOWN TOWARD THE SENSOR FOR THE CONNECTOR TO BE RELEASED, ONCE YOU REMOVE THE CONNECTOR THERE WILL BE ONLY A 10MM SCREW HOLDING THE SENSOR PULL IT OUT , THE SAME SETTING THE NEW ONE PUSH IT ALL THE WAY IN , THIGHT THE 10MM SCREW, CONNECT IT BACK AND YOU'RE DONE,BUT FOR THE ONE ON THE BACK SOMETIMES MIGHT BE NECESARY FOR YOU TO TAKE THE INTAKE OFF....HOPEFULLY IS NOT YOUR CASE....
Good luck!!! and if you need the crank for hard starting on hot/warm, it is located on the botton middle section on the transmission is the only cable that goes down to a small piece of metal and it is held by a 10mm screw only to protect the sensor, you will se the sensor once you remove that small about 6-8 inches piece of metal. Then you'll be able to unescrew the 10mm screw that holds the crank position sensor. when you pull it off you'll be able to see the fly wheel inside the transmission...
you all enjoy your rides out htere!!!
Posted on Jul 01, 2009
Tips for a great answer:
Aug 28, 2016 | 2007 Nissan Maxima
Jul 29, 2014 | 2004 Nissan Maxima
Apr 03, 2013 | Nissan Maxima Cars & Trucks
Jun 19, 2012 | Cars & Trucks
Jul 08, 2010 | 2002 Nissan Maxima
Apr 13, 2010 | 2004 Nissan Maxima
Mar 21, 2010 | 2007 Nissan Maxima 3.5 Sl Sedan
Jul 02, 2009 | 2004 Nissan Maxima
Jun 06, 2009 | 2001 Nissan Maxima
Oct 03, 2008 | 2000 Nissan Maxima
May 21, 2018 | Nissan Frontier Cars & Trucks
368 people viewed this question
Usually answered in minutes!