Question about 1999 Nissan Quest

1 Answer

Brakes? I have 1999 nissan quest that vibrates,when reach 55 mph and brake to make a stop. I have change the front brakes and caliper(drivers side). It also has some (light) brake burn smell.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 32 Answers

Change the rotors you most likly have a thickness variation causing the brakes to pulsate

Posted on Oct 22, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2004 nissan maxima vibrates when braking at high speeds


Warped brake rotors most likely cause. Other possibilities include wheel bearings, u-joints.

Aug 25, 2014 | 2004 Nissan Maxima

1 Answer

1999 chevy silverado. When braking truck start to vibrate. Changed front and rear rotors and brake pads. Just bought new tires.


I know on my Malibu the pads for the side against the caliper piston is different than the pad on the other side of the rotor.

Feb 03, 2014 | Chevrolet Cars & Trucks

1 Answer

Brakes- one side pulls more than other


replace calipers and bleed the system

May 07, 2012 | 2008 Dodge Durango Limited

3 Answers

1999 nissan quest brakes over heating


even though the parts are new they can still be bad the calipers are sticking have him replace them at no cost due to part being bad if he says no then go elsewhere

May 14, 2009 | 1999 Nissan Quest

1 Answer

2001 NISSAN QUEST VIBRATION


THE ORIGINAL VIBRATION MAY HAVE BEEN TIRES.IF THE LUG NUTS WERE NOT TORQUED BY HAND BUT OVERTIGHTED W/AN AIR RATCHET THE ROTORS MAY HAVE BEEN WARPED.TAKE IT BACK TO WERE THE TIRES WERE INSTALLED AND ASK THEM TO CHECK IT OUT.

Apr 30, 2009 | 2001 Nissan Quest

2 Answers

2001 brake pad replacement 2001 nissan quest


The hard part is pressing the caliper piston abck into the caliper so you can get the new, thicker pads over the rotor. A large C Clamp works best.

SECTION 206-03: Front Disc Brake 2001 Villager Workshop Manual
REMOVAL AND INSTALLATION Pads —Front Disc Brake Removal
  1. Remove the wheel and tire assembly. For additional information, refer to Section 204-04 .
  1. Remove the front disc brake caliper bolts. torx bit. T20?
  1. Support the front disc brake caliper from the front strut and spring assembly using mechanics wire.
  1. Remove the front disc brake pads.
    1. Remove the outboard front disc brake pad.
    1. Remove the inboard front disc brake pad.
Installation
  1. s1v~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Make sure the master cylinder reservoir does not overfill and spill brake fluid while retracting the front disc brake caliper piston.
    NOTE: It is necessary to fully retract the front disc brake caliper piston in the bore before installing the front disc brake pads.
    Install the front disc brake pads.
    1. Install the inboard front disc brake pad.
    1. Install the outboard front disc brake pad.
Caution. The outer pads are left and right. put left on driver side.
  1. Position the front disc brake caliper on the front-wheel knuckle and install the brake caliper pin bolts.
  1. s1v~us~en~file=ani_caut.gif~gen~ref.gif WARNING: It is necessary to depress the brake pedal several times to position the front disc brake caliper piston before driving the vehicle.

Apr 23, 2009 | 2001 Nissan Quest

2 Answers

2001 nissan quest brakes


You need a scan tool to hold open the control valves in the ABS, air is trapped in it and you can't bleed the brakes until you have the ABS held open

Apr 12, 2009 | 1999 Nissan Quest

1 Answer

Front brakes pull hard to right when applied


MAKE SURE THAT THE CALIPER WAS PROPERLY BLED AFTER INSTALLATION. YOU NEED TWO PEOPLE TO DO THIS. ONE TO PUMP THE BRAKES AND ONE TO OPEN THE BLEEDER VALVE.

Dec 14, 2008 | 1994 Nissan Quest

2 Answers

1999 nissan quest brake pad replacement


Remove wheel & tire,
remove 2 torx bolts that go from the inside to the outside of the vehicle. They are on the inner side of the brake caliper.
lift the caliper out of the rotor.
remove the brake pads.
To install, you must first squeeze the caliper piston back inot its bore. Do this slowly to prevent damage to the piston. You are forcing excess brake fluid back into the master cylinder reservoir. Slow constant pressure will get the job done. Use a large c clamp or a wooden hammer handel if that's all you have.
Fit the new brake pads in the calipers and slide the assembly back over the rotor.
install the 2 torx bolts, size 40? head I think.
You are done.
If rotors are scored bad, replace them too.

Jun 07, 2008 | 1999 Nissan Quest

Not finding what you are looking for?
1999 Nissan Quest Logo

317 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

74241 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22082 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...