Question about 1998 Honda Accord

Open Question

How dix this code p1738 on a 98 honda accord?

Just recently had my transmission rebuilt and my right axle replaced.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 740 Answers

SOURCE: 1998 Honda Accord transmission problem

This transmission have shift solenoids that are mounted on the outside in my personal experience I have rectified shift problem with these transmissions by simply change a solenoid or two. My recommendation is to put this vehicle on a code scanner and find out what is at fault first. If its a solenoid just replace, they are a dealer only part and that should take care of your problem. Good Luck and thanks for using FIX YA

Posted on Jan 05, 2009

Ad
  • 3 Answers

SOURCE: reset transmission speed sensor 93 honda accord

I have been looking for help with the VSS on 88 prelude. Found this page,maybe it will help you.

.http://techauto.awardspace.com/vss.html

Posted on Aug 10, 2009

  • 122 Answers

SOURCE: honda accord lx 1996 6 transmission dipstick

For the V-6 model, the dipstick is located down low on the transaxle, on the drivers side of the car, if it is low, usually 1 pint of of fluid is needed to raise from low notch to high notch. also if it appears to be dark or burnt, smells burnt, you should replace the tranaxle fluid. Good Luck!

Posted on Sep 07, 2009

abauto
  • 353 Answers

SOURCE: 1998 honda accord rebuilt transmission

There is a break in period on new transmissions, however it should not be shifting like you described. Shifting is controlled by sensors and solenoids, it is the clutch disks and friction plates that need to be broken in. A number of things could cause a transmission to act like this. You should have them do a whole system scan and find out if there are any faults. It there are, correct them before you damage the transmission.

If it were normal for a car to shift poorly with a new transmission, Honda would never sell any new cars.

Check fluid level and color - If it is burned, take it back immediately.

Posted on Sep 15, 2009

  • 1 Answer

SOURCE: 4 Diagnostic Codes for 2002 Honda Accord

p1738 p0135

Posted on Jan 31, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the cost of overhauling transmission?


with a fault of "problem in transmission control " this is a very general fault , but a good transmission shop that deals with Honda's might have access to a borrowed control module to test it out , who knows you might have to only buy one of these not an entire transmission , accord to transmission's dot com a 2ooo Honda transmission lists for 1253.00 dollars rebuilt ones go for about 2/3 that price

Dec 01, 2015 | 2000 Honda Accord

1 Answer

Transmission solenoid


You can get a replacement solenoid at a place like MB Transmissions on 63 San Jose Avenue in San Jose, Ca. They run about 40-75 bucks each. If you need another transmission, you can get a used one or a rebuilt one. Do you have a check engine light? If you do, you need to put it on a computer and get the codes for it. The codes will tell you what to do next. Flashing D light means a trans code is stored. How To Pull Honda Codes Without Scanner EricTheCarGuy

Mar 28, 2014 | 2007 Honda Accord Sedan

1 Answer

1997 honda accord transmission was rebuilt transmission and the transmission silinoid keeps going bad


When you rebuild a trans--you replace all solenoids

Take it back to the shop you had work done

Nov 20, 2012 | 1997 Honda Accord

1 Answer

HOW DO I FIX THIS CODE P1738 AND P1456? RECENTLY HAD TRANSMISSION REBUILT AND RIGHT FRONT AXLE.


Best to clear the computer codes & see what codes if any come back. You will need a scanner that can clear codes to do it .. Or if there is an Auto Value around you they can do it.

If P1738 returns I would bring the car back to the transmission shop.

I put the code details below.

P1738: Problem in 2nd Clutch Pressure Switch Circuit

P1456: Evaporative Emission Control System Leak Detected Small Leak

- Missing Fuel cap
- Incorrect fuel filler cap used
- Fuel filler cap remains open or fails to close
- Foreign matter caught in fuel filler cap
- Incorrect fuel tank vacuum relief valve
- Leak is in line between intake manifold and EVAP canister purge volume control solenoid valve.

Feb 07, 2012 | 1998 Honda Accord

1 Answer

2004 accord v6 6spd cv axle removal


You really should have a repair manual for this. You also
need a 1/2 inch socket set with a breaker bar. The torque
on the hub nut alone could be 180 ft pounds. Basically
you remove the hub nut, separate the tie rod end and the
lower ball joint from the steering knuckle to swing it away
from the drive axle. Don't forget to drain the gear oil from
the transmission before you pry the axle out of it. Rebuilt
drive axles are fairly inexpensive to purchase and you may
be able to find a service station to remove and install it or
just let them handle the whole affair. I'm assuming it's a
manual transmission, hence the term gear oil.

Feb 09, 2011 | 2004 Honda Accord

1 Answer

How to take out a cv axel from a 1992 honda accord


take tire off undo the nut on the axle undo ball joint remove axle from tire end then with a large pry bar pop the other end of axle out of transmission......place end of new axle in transmission and **** it in push hard and quick till it pops in and reverse previous steps

Feb 08, 2011 | 1992 Honda Accord

1 Answer

Recently had the transmission on my 1998 accord rebuilt. Now, in the morning, it shifts hard into second and slips into third for about 5 to 8 minutes and then it shifts normally for the rest of the day....


hmm.. well a cold shift issue ....remember heat expands all things so most likley there was an error with your repair i would take it back to who serviced it asap before your warranty runs out....good luck

Nov 30, 2009 | 1998 Honda Accord

1 Answer

New Transmission


Don't replace it... get it rebuilt for about $1400. You should receive at least a 12 month warranty with a rebuilt as well. Otherwise, new transmission plus labor - $2600

Jun 08, 2009 | 1995 Honda Accord

1 Answer

Transmission


Iit could be your half shaft axles that need replacing rather than the tranny. Jack up the front of your vehicle and support it with jack stands (safety should be your first priority). Grab your wheels and try spinning it. If it spins freely, you'll need to replace your axle. If your able to spin your wheel and engage the opposite side axle, chances are your axles are okay and the tranny is shot. Good luck.

Feb 20, 2009 | 1996 Honda Accord

2 Answers

Drive 4 indicator blinks when engine turn on


you need to check trans codes and go from there.
might need a trans.

Dec 11, 2008 | 2002 Honda Accord

Not finding what you are looking for?
1998 Honda Accord Logo

Related Topics:

693 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...