Question about Ford Mondeo

Open Question

Brake lights stay on continuously ford mondeo 2006

My brake lights stay on continously when i turn lights of auto lights on head lights and side lights

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 65 Answers

SOURCE: Auto door locking on Ford Mondeo

It sounds like it has been deactivated so we are going to reactivate the auto lock.

The numbers I will be saying will have to do with getting this to work so:
you will need to put the key in to the ignition switch.

1= is back to listen to the radio
2= is to get key out
3= is just before you start
4= is for starting your car

When we do this 1 and 4 will not be used
Do this and we will hope that it works like it should:

1: Turn the ignition with you key up to on( don't start)

2: Press the power door lock control 3 times

3: now turn the key back once (to off position)

4: Press the power door unlock control 3 times

5: ok turn the ignition back up 1 time. (The horn should chirp)

6: Then press the unlock control, then press the lock control, again (horn will chirp 1's) If auto lock
was activated.

7: Turn the ignition back 1's, Then the horn should chirp once to confirm the procedure was completed.
Nikki2913

Posted on Nov 29, 2008

Ad
karding_1984
  • 76 Answers

SOURCE: clutch does not release

did you check your pedal freeplay check your adjustment you need to have not more thant 1 inch freeplay on the clutch pedal what it does is when you did not adjusted right it cannot release your release bearing also check your linkage aite..

Posted on Feb 23, 2009

  • 24 Answers

SOURCE: illustrations on how to fit front brake pads to 1999 ford mondeo

Just observe how you take the old ones off. Pads can only snap in one way. It may take some effort but clean the caliper of rust you shouldn't have any problem. Remember to crack open your brake fluid reservoir before compressing the caliper!

Posted on Mar 30, 2009

  • 202 Answers

SOURCE: how to replace rear brake pads

Jack up car, remove wheel. There are two bolts that hold the caliper on. Remove these. Caliper comes off, take old pads out. There is a special tool to compress the piston back into the caliper (do not use a C Clamp on the rears.) Put new pads back on, re-install the caliper, and put the wheel back on. Pump the brake pedal until it is firm. Done.

Posted on May 27, 2009

  • 677 Answers

SOURCE: sticking rear brake caliper 2002 mondeo 1.8

Is the piston sticking in the caliper or is the caliper sticking on the outside slides preventing it from moving to the disc?

Posted on Aug 31, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Turn signal lights come on when I hit the brake's just got a ticket for malfunction is it normal for the turn signal lights to come on with the brake lights Chrysler 300 touring 2006


Nope, not normal. Brake lights come on when you press the brake pedal. Turn signals come on when you use the turn signal lever.

First check all the bulbs for continuity (that they work) and then check every fuse for continuity. If they are ok, do a visual check for damaged or chaffed wires to the lights. If no joy, head to an auto electrician.

Nov 24, 2015 | Chrysler Cars & Trucks

1 Answer

2006 mondeo 1.8 petrol - when filling up It seems like a breather pipe is blocked as petrol continuously shuts off every 2.00 or so... So it tTakes long time to fill


You have a problem is a device called the vapor recovery system for the gas filler neck and tank. You will need a dealer to find the problem.

Feb 14, 2015 | 2006 Ford Mondeo 1.8

1 Answer

How do i change reversing light switch 2006 mondeo ?


a/t or M/T.

unscrew the switch from the tranny
the A/T is a PRNDL switch on the side , see it, with huge connector
and is at the end of the SHIFT rod passing through tranny?

if M/T they look like a spark plug, 2 wires, screws in.

Jun 17, 2014 | 2006 Ford Mondeo 1.8

1 Answer

2006 Dodge Ram 1500 mega cab abs and brake lights stay on


check the sensors and connections may have loosened or knocked one loose if they look ok than have truck scanned most auto stores such as auto zone/advanced auto scan for free the trouble code will narrow the problem

Mar 24, 2010 | 2006 Dodge Ram 1500

1 Answer

2006 Ford Ranger. Rear passenger side tail light


Bad earth connection.Clean or replce wire.

Jun 18, 2009 | 2004 Ford Ranger

1 Answer

Clutch does not release


did you check your pedal freeplay check your adjustment you need to have not more thant 1 inch freeplay on the clutch pedal what it does is when you did not adjusted right it cannot release your release bearing also check your linkage aite..

Feb 23, 2009 | 2005 Ford Fusion

1 Answer

Auto door locking on Ford Mondeo


It sounds like it has been deactivated so we are going to reactivate the auto lock.

The numbers I will be saying will have to do with getting this to work so:
you will need to put the key in to the ignition switch.

1= is back to listen to the radio
2= is to get key out
3= is just before you start
4= is for starting your car

When we do this 1 and 4 will not be used
Do this and we will hope that it works like it should:

1: Turn the ignition with you key up to on( don't start)

2: Press the power door lock control 3 times

3: now turn the key back once (to off position)

4: Press the power door unlock control 3 times

5: ok turn the ignition back up 1 time. (The horn should chirp)

6: Then press the unlock control, then press the lock control, again (horn will chirp 1's) If auto lock
was activated.

7: Turn the ignition back 1's, Then the horn should chirp once to confirm the procedure was completed.
Nikki2913

Nov 23, 2008 | 2006 Ford Focus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

118 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...