Question about 1994 Land Rover Range Rover County

1 Answer

Changing headlamp bulbs

How do I release the plastic covers to get access to the bulb units? I want to install brighter Philips bulbs, but am unsure how the covers are released from looking at the car handbook

Posted by on

  • Ghento Oct 24, 2008

    two round lamps set in an oblong fitment (probably a later fitment) with round black plastic covers inside the engine bay for whaihc I cannot see a means of opening

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 22 Answers

Which headlamps have you got , round or square?

Posted on Oct 23, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change headlight lamp in 2005 Pontiac g6


To change the bulbs you need to first remove the 5 plastic pop screws on the front bumper. They're spread out at the top of the bumper right under the hood. Once you get those out, you have to remove the two hex bolts on each headlight. Then it gets tricky. You need to pull the light towards the front of the car until it pops out of the ball-bearing type mount on the fender. Once that pops out, you have to pull the front bumper forward while maneuvering the headlight out towards the front.

As per the manual it says as follows:---

Open the hood.

Hold the headlamp to prevent damage to the headlamp or to the fascia. Remove the bolts from the headlamp assembly. Remove the push-in-retainers across the front fascia. Remove the headlamp assembly. Lift the headlamp upward to release the locating tab from the front edge of the fender.

Disconnect the electrical connector from the headlamp assembly.

Remove the headlamp bulb access cover by rotating the headlamp bulb access cover counterclockwise, if necessary.

Remove the headlamp bulb from the housing by rotating the socket counterclockwise, if necessary.

Disconnect the headlamp bulb electrical connector, if necessary.

Remove the park/turn bulb access cover by rotating the cover counterclockwise, if necessary.

Remove the park/turn bulb from the housing by rotating the socket counterclockwise, if necessary.

Gently pull the park/turn bulb from the socket, if necessary. Install the park/turn bulb into the bulb socket.

Install the park/turn bulb socket into the headlamp housing by rotating the socket clockwise.

Install the park/turn bulb access cover by rotating the cover clockwise.

Connect the headlamp bulb to the headlamp electrical connector.

Install the headlamp bulb into the headlamp housing. Rotate the socket clockwise until locked.

Install the headlamp bulb access cover by rotating the cover clockwise.

Position the headlamp assembly to the vehicle. Lift the headlamp upward to release the locating tab to the front edge of the fender.

Install the bolts to the headlamp assembly. Tighten the bolts to 2 N·m (18 lb in).

Install the push-in-retainers across the front fascia.

Close the hood.

----------This will help.thanks.Helpmech.

Dec 25, 2010 | Pontiac G6 Cars & Trucks

1 Answer

Need help changing out the low beam on drivers side of 2006 buick rainier


Removal & Installation
Bulb Replacement
To Remove:

CAUTION
Halogen bulbs contain pressurized gas.
Mishandling a bulb may result in the bulb shattering into flying glass
fragments.

CAUTION
Make sure to wear eye protection when
handling a halogen bulb.

CAUTION
Do not touch the glass of a halogen bulb,
only handle the bulb by the base.

CAUTION
Do not allow a halogen bulb to come into
contact with dirt or moisture.

CAUTION
Make sure to dispose of a used halogen bulb
properly.

CAUTION
Do not allow children to handle halogen
bulbs.


  1. Turn the lamp switch to the off position.
  2. Make sure the bulb is cool before changing.
  3. Remove the headlamp assembly from the headlamp panel.
  4. Remove the rear access cover from the headlamp assembly.
  5. Disconnect the headlamp connector.
  6. Remove the bulb from the headlamp assembly by rotating the bulb and socket
    counterclockwise.

To Install:


  1. Connect the headlamp connector.
  2. Install the bulb into the headlamp assembly by rotating the bulb and socket
    clockwise.
  3. Install the rear access cover onto the headlamp assembly.
  4. Install the headlamp assembly into the headlamp panel.

Headlamp Assembly
Chevrolet
To Remove:






Headlamp Assembly (Chevrolet)
gm-06-00-1591.gif




  1. Remove the grille from the front of the vehicle.
  2. Release the headlamp assembly retaining tabs.
  3. If equipped, disconnect the headlamp leveling motor connector.
  4. Disconnect the headlamp connector.
  5. Remove the park/turn and side marker bulb sockets from the headlamp
    assembly.
  6. Remove the headlamp assembly from the headlamp panel.

To Install:


  1. Place the headlamp assembly into the headlamp panel.
  2. Install the park/turn and side marker bulb sockets into the headlamp
    assembly.
  3. Connect the headlamp connector.
  4. If equipped, connect the headlamp leveling motor connector.
  5. Lock the headlamp assembly retaining tabs.
  6. Install the grille onto the front of the vehicle.

GMC, Oldsmobile, Buick, Isuzu, and Saab
To Remove:






Headlamp Assembly (GMC, Saab, Oldsmobile, and Buick)
gm-06-00-1590.gif




  1. Release the headlamp assembly retaining tabs.
  2. Disconnect the headlamp connector.
  3. Remove the park/turn bulb socket from the headlamp assembly.
  4. For GMC, Saab, Oldsmobile, and Isuzu vehicles, remove the side marker bulb
    socket from the headlamp assembly.
  5. Remove the headlamp assembly from the headlamp panel.

To Install:


  1. Place the headlamp assembly into the headlamp panel.
  2. For GMC, Saab, Oldsmobile, and Isuzu vehicles, install the side marker bulb
    socket into the headlamp assembly.
  3. Install the park/turn bulb socket into the headlamp assembly.
  4. Connect the headlamp connector.
  5. Lock the headlamp assembly retaining tabs.


prev.gif next.gif

Oct 28, 2010 | 2006 Buick Rainier

1 Answer

How to replace headlight bulb on 2002 chevy trailblazer


Headlamp Removal & Installation Bulb Replacement To Remove:
CAUTION
Halogen bulbs contain pressurized gas. Mishandling a bulb may result in the bulb shattering into flying glass fragments.
CAUTION
Make sure to wear eye protection when handling a halogen bulb.
CAUTION
Do not touch the glass of a halogen bulb, only handle the bulb by the base.
CAUTION
Do not allow a halogen bulb to come into contact with dirt or moisture.
CAUTION
Make sure to dispose of a used halogen bulb properly.
CAUTION
Do not allow children to handle halogen bulbs.
  1. Turn the lamp switch to the off position.
  2. Make sure the bulb is cool before changing.
  3. Remove the headlamp assembly from the headlamp panel.
  4. Remove the rear access cover from the headlamp assembly.
  5. Disconnect the headlamp connector.
  6. Remove the bulb from the headlamp assembly by rotating the bulb and socket counterclockwise.
To Install:
  1. Connect the headlamp connector.
  2. Install the bulb into the headlamp assembly by rotating the bulb and socket clockwise.
  3. Install the rear access cover onto the headlamp assembly.
  4. Install the headlamp assembly into the headlamp panel.
Headlamp Assembly Chevrolet To Remove:
Headlamp Assembly (Chevrolet) gm-06-00-1591.gif

  1. Remove the grille from the front of the vehicle.
  2. Release the headlamp assembly retaining tabs.
  3. If equipped, disconnect the headlamp leveling motor connector.
  4. Disconnect the headlamp connector.
  5. Remove the park/turn and side marker bulb sockets from the headlamp assembly.
  6. Remove the headlamp assembly from the headlamp panel.
To Install:
  1. Place the headlamp assembly into the headlamp panel.
  2. Install the park/turn and side marker bulb sockets into the headlamp assembly.
  3. Connect the headlamp connector.
  4. If equipped, connect the headlamp leveling motor connector.
  5. Lock the headlamp assembly retaining tabs.
  6. Install the grille onto the front of the vehicle.

Jul 20, 2010 | 2002 Chevrolet TrailBlazer

1 Answer

Change headlinght bulb


SECTION 417-01: Exterior Lighting 2005 Freestyle/Five Hundred/Montego Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 03/14/2005 Headlamp Bulb adobe.gif Printable View (327 KB) Freestyle, Five Hundredn0035265.gif
Item Part Number Description 1 — Headlamp bulb electrical connector (part of 14290) 2 13N021 Headlamp bulb

Montegon0035266.gif
Item Part Number Description 1 — Headlamp bulb access cover screws (6 required) (part of 13006) 2 13N019 Headlamp bulb access cover 3 — Spring retainer (part of 13006) 4 13N021 High intensity discharge (HID) bulb 5 14A411 HID bulb electrical harness 6 — High beam bulb electrical connector (part of 13006) 7 13N021 High beam bulb Removal and Installation
ani_caut.gif WARNING: The headlamp bulb contains gas under pressure. The bulb may shatter if the glass envelope is scratched or if the bulb is dropped. Handle the bulb only by its base. Avoid touching the glass envelope. Failure to follow these instructions may result in personal injury.
NOTE: The headlamp bulb should not be removed from the headlamp assembly until just before a new bulb is installed. Removing the bulb for an extended period of time may affect headlamp bulb performance. Contaminants may enter the headlamp assembly where they can settle on the lens and reflector. Never turn on the headlamps with the bulb removed from the headlamp assembly.
NOTE: Make sure the headlamp switch and ignition switch are in the OFF position.
Freestyle, Five Hundred
  1. Rotate the headlamp bulb 1/8-turn counterclockwise and remove the headlamp bulb.
    • Disconnect the electrical connector.
Montego
  1. Remove the headlamp assembly. For additional information, refer to Headlamp Assembly — Five Hundred, Montego in this section.
  1. Remove the 6 screws and the headlamp bulb access cover.
Montego high beam bulb
  1. Rotate the headlamp bulb 1/8-turn counterclockwise and remove the headlamp bulb.
    • Disconnect the electrical connector.
Montego HID bulb
  1. Release the spring retainer and remove the HID bulb.
    • Disconnect the electrical connector.
All vehicles
  1. To install, reverse the removal procedure.

2010&c18=modelyear&c20=n920901&c35=wsm%2cheadlamp%20bulb%2cs5f%2c417-01%2cremoval%20and%20installation&s=1600x900&c=32&j=1.3&v=y&k=y&bw=1171&bh=582&ct=lan&hp=n&[aqe]

Apr 02, 2010 | 2005 Ford Five Hundred

2 Answers

How do i change headlight on a 2003 Murano


To change the headlight bulbs, you will need to remove the wheel liner cover to gain access to the back of the headlamp assemblies. Then you can pull off the screw cap / cover that seals the bulb into the headlamp assembly for the bulb you want to change. Once the cap is off, you will need to disconnect the harness from the back of the bulb. With the harness off, you will then need to either twist a black lock ring to release the bulb, or you will need to push on a metal lever to release the bulb (this varies on models and high and low beams).
Install in the reverse order....

Nov 16, 2009 | 2003 Nissan Murano

1 Answer

How to change the headlight on a 2004 bmw 5 series


if you have an entire headlight assembly (in case of accident) remove bumper, there are 8mm screws on the inner lining of the fron wheel well where the fender plastics and the air dam connect to the bumper, undo the screws concerning the bumper on bot sides of the car. then remove the plastic cover under the bumper (either philips screw heads or 10mm) and then under the aluminum re-enforcement strip behind the bumper (access from under the car) remove the torx screws that hold the bumper aluminum to the car frame, get a friend to help you pull the bumper off evenly an then seek the 8mm screws that hold the headlamp in place. the headlamp comes off the car strait out the direction of the front. disconnect the wires and connect the new lamp and fasten to the car. then do the assempbly in reverse order for the bumper installation.
for just changing the bulb, there are some rubber seals behind the light where the bulb rests. there are metal clips than you depress to release the bulb. install a new bulb and then replace the rubber caps.

Nov 07, 2009 | 2004 BMW 5 Series

1 Answer

How is cornering lamp changed in 2002 Buick Regal.



 
 
Lighting
Headlight Assembly
Removal & Installation
To Remove:

Open the hood.
Apply light pressure to the headlamp lens to hold the headlamp in place while disconnecting the retainers.
Lift up the retainers to release and remove the retainers.
Remove the headlamp mounting tabs from the slots in the upper fascia support and fender reinforcement.
Disconnect the wiring harness from the headlamp assembly.
Remove headlamp.
Remove the rubber access cover from the appropriate bulb to be replaced.
Rotate the headlamp bulb/socket counterclockwise to remove from the headlamp assembly.
To Install:
Connect the wiring harness to the headlamp.
Install the headlamp bulb/socket to the headlamp assembly rotating the socket clockwise until fully seated.
Install the rubber access cover.
Position the headlamp mounting tabs to the slots in the upper fascia and fender reinforcement.
Apply light pressure to the headlamp lens to hold the headlamp in place while installing the retainers.
Align the headlamp assembly retainers and slide them over the headlamp mounting tabs.
Close the hood.

 
Top of Form 1
Bottom of Form 1

Mar 30, 2009 | 2002 Buick Regal

2 Answers

How to change headlight bulb on ford mondeo


Very easy, 2 or 3 minutes.
Remove radiator grille. 2 plastic fittings on top, quarter turn and lift out grille.
Remove complete headlight. Simply lift out 2 L shape retaining pins. Disconnect lead. Ease out complete headlamp unit.
Remove back of headlamp unit to access bulbs. Disconnect lead from bulb while bulb still held by clip. Then release clip to remove bulb.
Reverse process to fit.

Jan 02, 2009 | 2001 Ford Focus

1 Answer

Change headlamp on a 1999 chevrolet malibu


The headlamp assembly on each side comes out as a unit. Raise the hood. Remove black plastic cover that hides the assembly. This is done by prying up on the plastic tabs on the cover that hold them in place. (They look like inserts) Once you pull up on the center portion of tab, the whole fastener comes out. Once the cover is out of the way, you will see these square black (about an inch Sq.) horizonal plates of which are connected to ball like fixtures (ball and socket) you pull up on the plates which release the ball to come out of the socket. The headlight assembly will swing out at the top, then raise straight up once it clears top. The headlight bulbs will now be accessible. Turn light bulb socket (with the wiring) counterclockwise 1/4 turn to remove. replace bulb. wipe clean with paper towel or cloth before reinstalling, as acid from skin or other contaminates will destroy bulbs. reinstall in reverse.

Road

Please rate me so I know if I helped.

Dec 19, 2008 | 1999 Chevrolet Malibu

1 Answer

HOW TO REPLACE HEADLIGHTS ON 2000 CHRYSLER LHS


ATTN: NIKKICARROLL

here is how to replace the bulb in your vehicle


  1. Release the hood latch and open the hood.
  2. Remove the radiator closure panel sight shield as necessary to gain access to the headlamp.
  3. Remove the screws holding the headlamp module halves together.
  4. Separate the module halves.
  5. Disengage the wiring from the headlamp bulb.
  6. Remove the retaining ring from the back of the headlamp bulb.
  7. Pull the bulb from the lamp.
To install:
  1. Push the bulb into the lamp.
  2. Install the retaining ring to hold the bulb in the lamp.
  3. Engage the wire connector to the back of the headlamp bulb.
  4. Place the module into position on the vehicle.
  5. Install the screws to hold the module to the vehicle.
  6. Install the radiator closure panel sight shield.
  7. Check the headlamp alignment and operation.
88176gb1.gif Exploded view of the fog lamp with the bulb removed
Click to Enlarge

  1. Release the hood latch and open the hood.
  2. Remove the radiator closure panel sight shield as needed to gain access to the headlamps.
  3. Remove the screws holding the headlamp module halves together.
  4. Separate the halves.
  5. Remove the fog lamp wire connector cover.
  6. Disconnect the wires from the fog lamp bulb.
  7. Disengage the retainer clip holding the bulb to the fog lamp.
  8. Remove the bulb from the fog lamp.
To install:
  1. Place the bulb into position in the fog lamp.
  2. Engage the retainer clip to hold the bulb to the fog lamp assembly.
  3. Attach the wire connectors to the fog lamp bulb.
  4. Install the fog lamp wires connector cover.
  5. Place the module halves together.
  6. Install the screws to hold the headlamp module halves together.
  7. Install the radiator closure panel sight shield.
  8. Verify the fog lamp operation and alignment

ATTN: WDSNEED1

Removal & Installation 88176g87.gif Remove the screws retaining the headlamp module to the mount adapter
Click to Enlarge

  1. Release the hood latch and open the hood.
  2. Remove the radiator closure panel sight shield as necessary to gain access to the headlamp fasteners.
  3. Remove the screws holding the headlamp module to the mount adapter.
  4. Separate the headlamp module from the mount adapter.
  5. Disengage the wiring from the headlamp and foglamp.
  6. Remove the headlamp from the vehicle.
To install:
  1. Attach the wires to the headlamp and foglamp assembly.
  2. Place the headlamp module into position on the mount adapter.
  3. Install the screws to hold the headlamp module to the mount adapter.
  4. Install the radiator closure panel sight shield.
  5. Check the headlamp alignment and operation.

Jul 28, 2008 | 1994 Chrysler New Yorker

Not finding what you are looking for?
1994 Land Rover Range Rover County Logo

Related Topics:

73 people viewed this question

Ask a Question

Usually answered in minutes!

Top Land Rover Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

yadayada
yadayada

Level 3 Expert

70387 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6880 Answers

Are you a Land Rover Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...