Question about 2000 Buick LeSabre

Open Question

Replace motor mounts on 2000 buick lesabre

Motor mounts

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

erietrack
  • 37 Answers

SOURCE: 2000 Buick LeSabre Struts

Yes there are struts on the front and shocks on the back. 2 of each. They are around $50-100 for the fronts. $30-100 for the rears depending if the car has air ride or not.

Posted on Nov 08, 2008

  • 975 Answers

SOURCE: Can't find the pcv valve on a 2000 Buick LeSabre.

assume this is a 3800,pcv is on pass side of plastic intake manifold,small plastic locking collar has an arrow on it ,says pcv

Posted on Mar 01, 2009

  • 106 Answers

SOURCE: 2000 buick lesabre - water pump replacement

first disconnect the battery then check how the serpentine belt is lined up so u can take it off and put back on. Then the pump should be on the side of the motor with 9or12 bolts there could be more! after taking out take razorblad and skrap the old gasket clean wipe of then put new gasket and pump back on dont over tighten the screws cuase the pump my be aluminum.

Posted on Mar 19, 2009

  • 196 Answers

SOURCE: 2000 Buick Lesabre custom liscense plate bulb

kind of tricky, took me an hour to get it figured out, but you got to opend the trunk and take out the 10 or so 10mm nuts sticking out of the backside of the lid, then the whole solid piece where the lights are on the back will slide off, then you can change the bulbs above the license plate and put it all back together

Posted on Mar 20, 2010

c17hydro
  • 2984 Answers

SOURCE: blower motor replacement

Very easy!!!

Here ya go!!!

Removal & Installation

  1. Remove the right side sound insulator in the passenger compartment.
  2. Disconnect the electrical connector from the blower motor.
  3. Disconnect the blower ventilation tube from the module.
  4. Remove the blower motor screws.
  5. Remove the blower motor from the housing.
  6. Install the blower motor into the housing.
To install:
  1. Install the blower motor screws and tighten to 15 inch lbs. (1.5 Nm).
  2. Install the blower ventilation tube to the module.
  3. Connect the blower motor electrical connector.
  4. Install the right side sound insulator.

Posted on Jun 03, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I own a 2003 buick lesabre. Why does the motor move when you push on it?


To check motor mounts transmission in drive parking brake on accelerate lightly if a mount is worn the engine will raise up. also check in reverse.

Oct 18, 2014 | 2003 Buick LeSabre

1 Answer

How do you replace engine mount on 2000 buick


Put car on jackstands so you can work under car. Put 2 inch thick 5": x 5" wood board on jack under oil pan. Jack up slightly. Unbolt broken mount & replace with new one.

Oct 22, 2013 | 2000 Buick LeSabre

2 Answers

Locate canister purge solenoid for 2000 Buick lesebra


The evaporative canister purge valve is found between the upper intake manifold and the rear valve cover.

Nov 01, 2009 | 2000 Buick LeSabre

1 Answer

2000 buick lesabre Heat control will not switch


their is a little motor on your duct work that moves a door open and closed to switch from heat to cool,it is called actuator motor.watch it and have someone to switch it from cool to heat to Se if the motor is turning.

Oct 10, 2009 | 2000 Buick LeSabre

2 Answers

Engine temp is fine - thermostat OK - no heat


The blend motor to go from cold to hot is located on the blower motor housing. They are usually mounted close to the blower motor.

Oct 02, 2009 | 2000 Buick LeSabre

1 Answer

Trying to reach my back plugs on a 2001 buick lesabre


The technical term for those "dog bones" are lateral torque struts. The motor mounts hold and support the power train vertically.
Hope this helps, let me know.
Regards,

Apr 06, 2009 | 2001 Buick LeSabre

1 Answer

2000 buick lesabre - water pump replacement


first disconnect the battery then check how the serpentine belt is lined up so u can take it off and put back on. Then the pump should be on the side of the motor with 9or12 bolts there could be more! after taking out take razorblad and skrap the old gasket clean wipe of then put new gasket and pump back on dont over tighten the screws cuase the pump my be aluminum.

Mar 17, 2009 | 2000 Buick LeSabre

1 Answer

Motor and transmission mounts


Did you reconnect the shift link on the transmission?

Aug 14, 2008 | 2000 Buick LeSabre

3 Answers

2000 Buick LeSabre Struts


Yes there are struts on the front and shocks on the back. 2 of each. They are around $50-100 for the fronts. $30-100 for the rears depending if the car has air ride or not.

Jul 17, 2008 | 2000 Buick LeSabre

Not finding what you are looking for?
2000 Buick LeSabre Logo

Related Topics:

367 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...