Question about 1999 Ford Explorer

2 Answers

How do i get my entrey code for the doors - 1999 Ford Explorer

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Ford Master
  • 75,822 Answers

The codes are on the keyless entry module, it is a tag. The module is behind the rear driver side interior quarter panel trim panel, that is the huge cover on the rear deck over the weheel whell humps. It is at the front near the roof "B" pillar.

Posted on Feb 07, 2012

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 17,970 Answers

Hi Joe:
You can use the keyless entry keypad to Lock or unlock the doors without using a key.
Open the liftgate window. Activate or deactivate the autolock feature.

This code is located on the owner's wallet card in the glove box, is available from your authorized dealer via scan code or is marked on the computer module.

Computer Module location
1995 thru 2001 is located in the jack storage compartment in the rear of your Explorer. First remove the panel to the jack storage compartment. Towards the front of this area you should see a metal box this is your auto-lock module (way up front next to your rear left passenger seat - Image 01). On the back side of this is your 5 digit code factory preset code (Image 02). It is hard to get to. To see it you will have to loosen, pull, use a flashlight or a mirror but it can be done.


how do i get my entrey code for the doors - 2_7_2012_7_54_27_pm.jpg
Image 01

2_7_2012_7_54_51_pm.jpg

Image 02

I have one 1997 Explorer XLT and I find it there; if you need some additional details, images or others, just CLICK HERE to contact us

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Posted on Feb 07, 2012

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

After about 20 tries locking and unlocking with keyfob. It will will blow fuse.


Blown fuses indicate a short either in the wiring or in the module.

May 10, 2015 | 2003 Chevrolet Impala

1 Answer

Cannot open drivers door of my 1996 honda crv automatic using key or from inside. having to climb over from passenger side to drive and get out again.


Sue we arn't talking keyless entrey here .
Then if the key works in the other locks it must be good not worn out .
Witch leaves the lock cylinder on the drivers door or the mechinizam that moves the rods inside of the door to lock and unlock it .
Dose the key feel like it fits ok and the lock turn normally .If so that leaves the mechinizam inside the door .
Its not the end of the world likely something popped off or a little plastic clip broke that holds the rod in place .
The door needs to be taken apart from the inside witch means it needs to be open to repair .Its like a caught 22 can't fix it unless its open but can't open it .
There are ways slim jim or the old coat hanger way if you can roll the window down think about it do a little reserach it can be opened with out distroying the door

Apr 24, 2015 | Honda CR-V Cars & Trucks

1 Answer

Where is the door code for my 2005 ford 500 so I can reset it


Your door code should be on a sticker inside the trunk lid. That's where Ford put it on my several different models.

Sep 17, 2014 | Cars & Trucks

1 Answer

My keyless entrey will not work has new battery?


Hi, please try reprogramming the fob using these procedures, and thankd for using FixYa:
Close all doors
2. Insert key into ignition
3. Hold down the power UNLOCK button on the driver's door panel, continue to hold down
until instructed to release in step 9.

4. Perform steps 5 through 8 in a fairly rapid succession.
5. Turn the ignition to the ON position (as far as you can go without starting the engine.)
6. Turn the ignition to the OFF position.
7. Turn the ignition to the ON position (as far as you can go without starting the engine.)
8. Turn the ignition to the OFF position.
9. Release the power UNLOCK button on the door panel. The vehicle should respond by
door locks locking and unlocking automatically. (If locks do not cycle after you let go,
not before you let go of the unlock button, then the vehicle has not entered programming
mode and you must start procedure over. Remove key from ignition, open drivers door
and return to step 1 ). If the locks do cycle automatically then proceed to step 10.

10. Hold down the LOCK and UNLOCK buttons on the remote until the doors lock and
unlock. This may take up to 30 seconds.

11. Repeat step 10 NOW for each additional remote. (Including any existing remotes).
12. Turn the ignition to the ON position to exit the programming mode.
13. Test remote(s).

Jan 14, 2011 | 2003 GMC Sierra 1500

3 Answers

Lost keys for 1999 jeep grand cherokee how do i


only the dealer can repair this, the Body control computer must be programmed to the new lock cylinder, there is no way around this.

Aug 16, 2010 | 1999 Jeep Grand Cherokee

1 Answer

My key died for my 2005 GTO. Can the battery be


your key died? your remote keyless entrey? or the key won't start it no more? if the key won't start it no more try this before wasting money. turn the ingintion switch to the on postion for about 1 sec,. turn off then turn it right back on wait about 30 mins,. then try to start the car. we have alot of problems with them losing the programing for the transponder in the key with the halls effect,. this will usually fix this problem. hope it helps. thanks. and have a great week.

Mar 10, 2010 | 2005 Pontiac GTO

3 Answers

LHJ001 WIRING


I have the 1995-97 Lincoln Continental Alarm, Remote Starter, Keyless Entry Wiring, review it:

b94b6e9.png


Hope helped.

Oct 30, 2009 | 1996 Lincoln Continental

1 Answer

Keyless entry does not work outside the car have to use key to enter the car but once inside the keyless entrey works fine


have you changed the battery in it ever?
if not try changing the battery out then it should all be ok.

keep me posted.
thank you
jm

Jul 29, 2009 | 2007 Chevrolet Impala LS Sedan New Cars

1 Answer

HOW TO OPEN THE DOOR USING THE NUMBER PAD ON THE DOOR


this from the owners manual
Programming your own personal entry code
To program your own code:
1. Enter factory set code (keypad will illuminate when pressed).
2. Press 1/2 control within five
seconds of step 1.
3. Enter your personal 5 digit code.
Enter each digit within five seconds
of previous one.
Do not set a code that includes five
of the same number or presents
them in sequential order. Thieves
can easily figure out these types of codes.
Your personal code does not replace the permanent code that the
dealership gave you. You can use either code to unlock your vehicle. If a
second personal code is entered, the module will erase it in favor of the
new code.
If you wish to erase your personal code, use the following instructions:
1. Enter factory set code.
1 2 3 4 5 6 7 8 9 0
Controls and features
90
2. Press 1/2 control within five
seconds of step one.
3. Press 7/8 control and 9/0 control
at the same time within five seconds
of step 2.
The system will now only respond
to the factory set code.
Unlocking the doors with the keyless entry system
To unlock the driver door, enter either the factory set code or the
personal code (each digit must be pressed within five seconds of the
prior digit). The interior lamps will also illuminate.
To unlock all doors, enter the factory set code or personal code (driver
door unlocks) and press the 3/4 control within five seconds.
Locking the doors with the keyless entry system
It is not necessary to enter the factory or personal code prior to locking
all doors. To lock the doors:
² Press the 7/8 control and the 9/0 control at the same time.
Activating/deactivating
.

May 19, 2009 | 2000 Ford Expedition

Not finding what you are looking for?
1999 Ford Explorer Logo

136 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...