Question about Ford Taurus

Open Question

How to remove the gear shift knob 2003 taurus

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 85 Answers

SOURCE: removal of gear shift knob

There are two types of shift knobs. One that unscrews and one that the lower trim of the shift knob separates from the knob using a trim stick. After separating the lower trim from the knob pull upward to release the knob from the shift lever. If a new shifter assembly is being installed, unscrew the original shift knob or separate the lower trim from the knob and pull up to remove the knob from the shift lever. Screw the knob onto the new shifter assembly's lever no more than 14 turns or install the lower trim onto the shift lever then push the knob onto the shift lever and install the lower trim piece onto the shift knob.

Posted on Jul 03, 2008

Ad
  • 13 Answers

SOURCE: 1998 camaro, v6 automatic, gear shift knob ??

If it is neither suggestion by bunnydawg, try looking on the back of the shifter for a metal staple that needs to be pulled out.

Posted on Oct 30, 2008

jschoon77
  • 55 Answers

SOURCE: Gear shift knob

The shifter knobs on these vehicles is installed very very tightly.

I have never been able to remove one without ruining it by tearing the cover, which should not be a big issue since you're replacing it.

The knob threads on like a nut would (lefty-loosy, righty-tighty). I use a large set of channel-lock pliers and they are still tough to break loose.

Good luck and I hope that this is helpful!



Nissan Scope Technician- 10+ years experience in Nissan dealership.

Posted on Nov 04, 2008

  • 217 Answers

SOURCE: I need to remove the gear shift knob on a 1993 Pontiac grand am

have to shift out of park engine off key on and their will be a pin or screw on the front side of gear shifter

Posted on Jan 17, 2009

  • 1 Answer

SOURCE: Removing Factory Gear Shift Knob for 2001 Jetta

On my 2000 jetta glx, I had to replace both the shift knob and boot as one. It is built as one unit. You have to pull the boot up over the shift knob, break/bend a clip to "unlock" the shift knob then pull up. I hope the new knob you got has the boot built in and comes with a new clip.

Posted on Mar 27, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need to remove a gear shifter from a 2003VW passat


gear shifter as transmission inside it. well best replace transmission or you'll need a pulley and few sockets. as the shift. the shift you pull the knob or act as if you are prying it out it stay out. once out far enough push down on the bottom sparkling part of the stick. once down pull knob. then fallow the screw on side for removal.

Mar 15, 2014 | 2003 Volkswagen Passat

1 Answer

How to install original gear shift knob on my 2003 eclipse gts


Carefully check the button and stick. I suspect that there may be a piece broken off of the button so it doesn't reach into the slot properly.

Feb 12, 2018 | Cars & Trucks

1 Answer

I took my 2003 pontiac grand am to get a paint job. They broke my gear shift knob. In order for me to go into gear I had to put the broken gear shift knob in. Then I took it to wal-mart for an oil...


Contact an automotive recycler (junkyard) to see if they will sell you one. Often you can buy one that fits (but looks different) from an auto parts store like AutoZone or Checker.

Aug 29, 2010 | 2004 Pontiac Grand Am

1 Answer

How can I remove gear shift knob on a 2003 Navigator?


it looks like you disconnect the shift cable and remove the center console finish panel with the shifter.


SECTION 501-12: Instrument Panel and Console 2003 Expedition/Navigator Workshop Manual
REMOVAL AND INSTALLATION Floor Console —Front, Navigator Removal and Installation
  1. Apply the parking brake.
  1. Position the front seat forward.
  1. Remove the two front floor console rear bolts.
  1. Position the front seats rearward.
  1. Disconnect the battery. For additional information, refer to Section 414-01 .
  1. Remove the pin-typ retainer and the window control switch panel.
    • Disconnect the electrical connectors.
  1. Move the shift lever to NEUTRAL and position the shift indicator bezel aside.
  1. Remove the screws and the center console finish panel.
    • Disconnect the electrical connectors.
  1. Disconnect the shift cable.
  1. Disconnect the front floor console electrical connectors.
    1. Loosen the electrical connector bolt.
    1. Disconnect the connector.
    1. Disconnect the electrical connector.
  1. Remove the front floor console side finish panel.
    • If equipped, disconnect the electrical connector.
  1. Remove the front floor console front bolts.
  1. Remove the floor console.

Apr 17, 2009 | 2003 Lincoln Navigator

2 Answers

04 Navigator gear shift button broken


I only have 2003 Nav procedure. Maybe get used part at car-part.com. Page with * is lowest price.

SECTION 307-05: Automatic Transaxle/Transmission External Controls 2003 Expedition/Navigator Workshop Manual
REMOVAL AND INSTALLATION Selector Lever —Floor Shift Removal and Installation
  1. Lift the floor shift PRNDL bezel.
  1. Disconnect the PRNDL bezel wire harness connector.
  1. Remove the shift lever handle and cover.
    1. Slide the handle bezel down.
    1. Remove the screw.
    1. Disconnect the TCS wire harness.
    1. Lift assembly from the shifter lever.
b038436.gif
  1. Position the window regulator control panel aside.
  1. Remove the screws and the console finish panel.
  1. Remove the left side console access panel.
  1. Disconnect the transmission shift cable from the transmission selector arm.
  1. Remove the transmission shift cable retaining clip from the floor shift mechanism through the console access.
  1. Remove the four bolts retaining the floor shift mechanism to the floor.
  1. Disconnect the floor shift mechanism wire harness connector.
  1. Remove the floor shift mechanism from the console.
  1. Remove the brake shift interlock actuator, parking brake release mechanism and harness.
    • Remove the wire harness retainers.
    • Remove the wire harness retainers.
    • Remove the two screws retaining the brake shift interlock assembly.
    • Remove the two screws retaining the parking brake controller.

Mar 15, 2009 | 2004 Lincoln Navigator

1 Answer

2002 VOLVO S60 automatic


I want to change the boot on my 2003 Pasatt..It seems to be connected to the gear shift knob...How do I get the knob off ??

Jun 29, 2008 | 2002 Volvo S60

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

268 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

80637 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

fordexpert

Level 3 Expert

5687 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...