Question about Cars & Trucks

1 Answer

The turning dance floor in fezziwig's ballroom doesn't turn and makes a grinding noise. can i repair it?

Posted by Anonymous on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 2 Answers

I can replace your Fezziwig ballroom motor! I have done hundreds of them. Stratford Band Instrument Services 203 260 5247

We can rebuild your Fezziwigs ballroom motor! We finally located the parts! Send your motor I will replace the broken motor with a new one- to remove the old one heat the silicone with a blow driver, gently use a razor to cut through and carefully remove! To replace it- clear silicone it back in. I need the entire unit so I can test it before sending it back - I have done a dozen of these. I can also send a replacement motor - see my web store

Posted on Jan 16, 2015

  • frank block
    frank block Nov 24, 2016

    what type of tool is available to get the back off phillips no good

×

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
Larrysito
  • 73 Answers

SOURCE: Grinding noise from rear end when making sharp turns.

rear diff damage ...check

Posted on Aug 30, 2009

ghost45
  • 1280 Answers

SOURCE: Grinding noise when making right turns.

CV joint. Take/Tow your vehicle to an authorized Hyundai dealership and pay the diagnostic fee... they will tell you exactly what the problem is and the cost of parts/labor to fix it... at least this way you'll know what the problem is and what's required to fix it.

Posted on Oct 03, 2009

  • 14036 Answers

SOURCE: grinding noise when i make right turn

sound like rear axle bearings.

Posted on Apr 16, 2009

alicantecoli
  • 22246 Answers

SOURCE: when brake are applied petel goes to floor, grinds, shakes

Take to a garage right now ,do not drive or evan think about using this vehicle.Call a tow truck ,Has this vehicle passed its annual mechanical vehicle inspection ??

Posted on Jan 01, 2010

Testimonial: "Thank U! Very Much, I Did Not Buy This Truck Because To Many Things Did Not Feel Right. Dave"

01fordeb
  • 1033 Answers

SOURCE: 2000 chevy cavalier, when turning left makes

Check the under fender. Sometimes the black plastic will come loose around the wheel area. Turn your wheels to the left and see if the tire are rubbing close to any part of the fender area.

Posted on May 10, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Full lock grinding noise micra


A "CLICKING" NOISE WHEN TURNING USUALLY INDICATES A BAD CV JOINT. LOOK AT SIDE MAKING NOISE AT INNER AND OUTER CV RUBBER BOOTS...IF CRACKED OR TORN....PROBABLY NEED NEW CV JOINT

Jul 30, 2012 | Cars & Trucks

1 Answer

Have 93u honda civic sedan replaced rack and powersteering pumping when turning make grinding noise what would cause that?


Was the noise there prior to the repairs you had done? If yes check your wheel bearings. If loose it is possible that the rotor may contact the caliper bracket making a grinding noise.

May 09, 2012 | 1993 Honda Civic 4 Door

3 Answers

Front right turn dragging/grinding noise


Possibly a broken wheel bearing. Have a mechanic check it out.

Jul 23, 2017 | 2000 Oldsmobile Alero

1 Answer

I have a 2000 chevy cavalier and there is this grinding noise in the front end. it sounds like its in the middle but the noise is in perfect rotation with the tires. it just started with grinding but now...


From what you described, it sounds like you may have a CV axle going bad. The tripods are located somewhat near the center of the vehicle, near the transmission, and the fact that it gets worse in turns helps to reinforce my guess. Try this. Go into a large parking lot where you can make a minimum radius turn ( with your wheel turned as hard as it will go.) Do a few circles in each direction. If the sound gets substantially worse while turning than it is while driving straight, this is a good indicator that your CV axle is going bad. If that's the case, don't delay in getting it repaired. If it goes out, it will leave you stranded.

May 10, 2011 | 2000 Chevrolet Cavalier

1 Answer

Grinding noise when turning wheel


I have heard a lot of dry outer tie rod ends and ball joints causing this problem. Ford used non greasable front end parts in those years.Could also be in the strut mounts. Get a second opinion. If it makes the noise sitting still it should be easy to find with stethascope or chassi ear.

May 22, 2010 | 1997 Lincoln Continental

1 Answer

Grinding noise when making right turns.


CV joint. Take/Tow your vehicle to an authorized Hyundai dealership and pay the diagnostic fee... they will tell you exactly what the problem is and the cost of parts/labor to fix it... at least this way you'll know what the problem is and what's required to fix it.

Sep 30, 2009 | 2004 Hyundai Elantra

1 Answer

Pontiac G5 Grinding noise while turning left.


your axle is making noise,will need to be repaired.if my info was of any help to you please leave a comment ,vote,note.thankyou

Sep 04, 2009 | 2006 Chevrolet Cobalt

3 Answers

I accelerate my 2000 neon, and it vibrates and get grinding noise


Check the front drive axles and boots. A bad cv (constant velocity) joint can cause this.

May 09, 2009 | 2004 Dodge Ram 1500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

516 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...