Question about Cars & Trucks

Open Question

How to replace the starter on 2007 buick lucerne

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
emissionwiz
  • 77514 Answers

SOURCE: 2007 Buick Lucerne

it is released by means of a vacuum motor, if that is not working u can go under the dash and manually release it by pulling the small lever that the vacuum actuator is attached to..

Posted on Jan 10, 2009

Ad
honeymokey
  • 3113 Answers

SOURCE: 2007 buick lucerne has water leaking into the

Remove trunk trim and covers , close trunk and wet car now look for leak source.

Posted on Jun 16, 2009

duane_wong
  • 6826 Answers

SOURCE: How do you jump start A battery on the 2007 buick

Very simple.

First hook up Positive Red and Negative Black terminals to the battery in the known good car. Then hook the Red terminal on the opposite end of the jumper cables to the positive Red terminal of the battery in the known bad car. Then, carefully, without shorting out the connectors, connect the final black jumper cable to the 'frame' of the known bad car.

Hope this helps.

Posted on Jul 13, 2010

  • 565 Answers

SOURCE: My 2007 Buick Lucerne drivers

first purchase the door handle assembly then remove the door panel. make sure the window is up and reach in and disconnect the rods making a note of which one goes to which one. unbolt the door handle and remove. the new door handle may come with a new rubber seal for it. position over new handle and reinstall. make sure to search the door panel for hidden screws holding it on before you pop the clips.. hope this helps

Posted on Feb 05, 2011

clifford224
  • 1975 Answers

SOURCE: I have a 2006 Buick Lucerne CXS and I'm wondering

There are 2 different engines that came in the Lucerne in 2006 and I am not sure which one the CXS had. In any case below are pictures of both engines as well as locations. If you have the 3.8 liter (6 cylinder) engine you can add coolant directly to the radiator in the spot marked "A". But on your regular fluid checks you want to make sure that where the "B" is marked that the overflow tank there has fluid up to the line that says "full". If you have the 4.6 liter (8 cylinder) engine the overflow tank and where you fill up the radiator are the same (location "A") so that is the location you would fill the radiator as well as check to make sure there is coolant to the "full" line on the tank on your regular fluid checks, When you look at the pictures below you will understand easier. I hope this helps and good luck.

clifford224_823.gif


clifford224_824.gif

Posted on Jun 15, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you take apart the dashboard to replace the ambient air temperature sensor on a 2007 Buick Lucerne?


ambient air temperature is the air outside the cabin not inside it, otherwise it would rise as the car warmed up. Or do you mean the temperature that the heater works from? In which case, Google

Buick Lucerne Remove Dashboard.

Someone will have a YouTube video.

Feb 04, 2016 | 2007 Buick Lucerne

1 Answer

How long does it take to remove and replace rear hub bearing in 2007 Buick Lucerne


My info says 2 1/2 hours, both sides. I have to be honest, I doubt I could do that in 2 1/2 hours.

Dec 15, 2014 | 2007 Buick Lucerne

3 Answers

How do I replace a headlight assembly on a 2007 Buick Lucerne?


ouch on this buick...
requires a little more work..
1.6 hrs with headlamp alignment.
replace-headlight-assembly-2007-buick#solution-section-eiq04jcqehklpmop1towry5q-4-9.jpg
replace-headlight-assembly-2007-buick#solution-section-eiq04jcqehklpmop1towry5q-4-20.jpg

Nov 12, 2014 | 2007 Buick Lucerne

1 Answer

Replace front wheel bearing hub torque


front wheel bearing hub nut torque - 2007 Buick Lucerne CXS Sedan is 118 Ft. pounds

Jan 28, 2014 | 2007 Buick Lucerne CXS Sedan

1 Answer

Replace headlight assembly on 2007 buick lucerne


To change the headlight get under the car and reach up behind the bumper to change the bulb very easy took me 3min

Jul 12, 2011 | 2007 Buick Lucerne CXS Sedan

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

89 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

77514 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14398 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...