Question about Subaru Impreza

Open Question

Intake valve control solenoid location

Check engine light on and cruise light on

Posted by Anonymous on

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
johnjnail
  • 1702 Answers

SOURCE: check engine light on, traction

there is a lot of questions here so i will start with the codes P0028 & P0026 both are verable valve timing codes first we should talk about how this system works, the engine is equiped with veriable valve lift units that when oil is pushed into the units they push on the camshaft, basicaly they roll the shafts in there saddles witch changes the lift and duration of the camshaft this is done to maxamise the performance of the engine, basickly alowes the engine to be tuned down at low RPM and load but when there is a demand for power the cames are advanced to give the engine more power. when we see these codes the mose common problem is the engine has not been serviced reguarly and their is gunk built up in the oil passages to the veriable valve units, most of the time changing the oil and adding some addative like marvel mistery oil will fix the problem, if not then you may have to replace the veriable valve lift units.

the skip under load might be the verable valve units advanceing one cam and not the other, this would cause a surge and maybe an engine miss fire, but i would change the spark plugs as will as the oil ( it never hurts to replace the plugs ) but make sure to use what the factory used don't chepen it up spend the few extra dollers to get the right plugs.

the check engine light is the verable valve units.

now the flashing cruse and the TCL these are most likely related, and you should be able to get a code from the BCM that will leed you down the right path, but best guess is a speed sensor is not working, all 4 wheel have to be within 1% of each other or the cruse will not work, and the TC wont work and probly the ABS.

its a lot of info but i hope this helps.

Posted on Mar 12, 2011

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need to know code p0028 is making. Check engine. Light stay on and engine will not idle


code p 0028 refers to intake valve control solenoid circuit , bank 2 ---range performance problem===causes--wiring ---intake valve control solenoid
this solenoid controls the advance / retard of the valve timing for the inlet valve camshaft and will account for the idle problem and the engine light
take it to an accredited service center who has experience on your make of vehicle and have the wiring checked or the solenoid replaced

Dec 01, 2016 | Cars & Trucks

1 Answer

0083


P0083 - Intake Valve Control Solenoid Circuit High Bank 2Possible causes - Faulty Intake Valve Control Solenoid Valve
- Intake Valve Control Solenoid Circuit harness is open or shorted
- Intake Valve Control Solenoid Circuit circuit poor electrical connection help.png Help with this Symptoms- Engine Light ON (or Service Engine Soon Warning Light) P0083 Description Intake Valve Control Solenoid Circuit High Bank 2 is the generic definition for the P0083; however your vehicle's manufacturer may have a different definition and information for the P0083 code.

Apr 14, 2013 | 1999 Chevrolet Lumina

1 Answer

Quest code p1136


P1136 NISSAN - Intake Valve Timing Control Solenoid Valve Circuit Bank 2
Possible causes- Intake valve timing control solenoid valve bank 2 circuit is open or shorted.
- Intake valve timing control solenoid valve bank 2 circuit connectors
- Intake valve timing control solenoid valve bank 2 Tech notes Since the Intake valve timing control solenoid valve uses oil flow to control timing, dirty oil can cause the valve to stuck open or close. Before replacing the valve, change engine oil and filter and reset engine code.

Aug 29, 2012 | 2005 Nissan Quest

1 Answer

P0011 code. My car started jurking in the middle of traffic about a month ago. The first week, I replaced the cam sensor and it drove smooth for 2 weeks but the jurking came back. I got the cam sensor from...


PLEASE READ ALL THIS INFO.

MAKE SURE THE ENGINE OIL IS CLEAN AND CHANGED AT PROPER INTERVALS
P0011 NISSAN - Intake Valve Timing Control Performance Bank 1

Symptoms - Engine Light ON (or Service Engine Soon Warning Light)
- Possible engine lack/loss of power
- Posssible engine rough idle
Possible causes - Harness or connectors
- Intake valve timing control solenoid valve circuit is open or shorted
- Intake valve timing control solenoid valve may be faulty
- Crankshaft position sensor (POS) may be faulty
- Camshaft position sensor
Tech notes Since the Intake valve timing control solenoid valve uses oil flow to control timing, dirty oil can cause the valve to stuck open or close. Before replacing the valve, change engine oil and filter and reset engine code. When is the code detected? When there is a gap between angle of target and phase-control angle degree, the valve will stop working and the ECM will trigger the P0011 code. P0011 NISSAN Description This mechanism hydraulically controls cam phases continuously with the fixed operating angle of the intake valve.

The ECM receives signals such as crankshaft position, camshaft position, engine speed, and engine coolant temperature. Then, the ECM sends ON/OFF pulse duty signals to the intake valve timing control solenoid valve depending on driving status. This makes it possible to control the shut/open timing of the intake valve to increase engine torque in low/mid speed range and output in high-speed range.

The intake valve timing control solenoid valve changes the oil amount and direction of flow through intake valve timing control unit or stops oil flow. The longer pulse width advances valve angle. The shorter pulse width retards valve angle. When ON and OFF pulse widths become equal, the solenoid valve stops oil pressure flow to fix the intake valve angle at the control position.
MAKE SURE YOUR OIL IS CLEAN AND CHANGED AT PROPER INTERVALS.

Sep 07, 2011 | 2006 Nissan Altima

1 Answer

What fuse is speed control


First, Please review these articles:

Where's The Fuse?

What Else Could Be Wrong?

Then to answer the question you asked...

There are actually three fuses involved in your cruise control system.

> The first is the "Cruise Control, EAT ECU" fuse. it is Fuse #4 in the Underdash Fuse And Relay Box. it is a 7.5 Amp fuse. This fuse also powers the gauge assembly, the alternator control circuit, the Radiator Fan Control Module, the Intake Air Bypass Control Solenoid Valve, The EGR Control Solenoid Valve, The EVAP Canister Bypass Solenoid Valve, the EVAP Canister Vent Control Solenoid and the Heated Oxygen Sensor Heater circuits. If this fuse is blown, the engine will not idle, The alternator will not charge the battery and the transmission will not shift properly. In general, a whole bunch of stuff will not be working.

> Next is the "Backup, Metering Lights, Turn Signals" fuse. It is Fuse #1 in the Underdash Fuse And Relay Box. It is a 10 Amp fuse. As you can tell by the description, your backup lights, dash warning lights and turn signals will also not be working if this fuse is blown.

> Last there is the "Stop Light, Horn" fuse. It is Fuse #30 in the Underhood Fuse And Relay Box located at the right rear of the engine compartment. It is a 20 Amp fuse. As you might guess, your horn and stop lamps will also not be working if this fuse is blown.

Jun 04, 2011 | 1995 Honda Accord

2 Answers

Getting code poo11 on a 03 nissan maxima. which bank is it?


When there is a gap between angle of target and phase-control angle degree, the valve will stop working and the ECM will trigger the P0011 code.

P0011 NISSAN - Intake Valve Timing Control Performance Bank 1
This mechanism hydraulically controls cam phases continuously with the fixed operating angle of the intake valve.

The ECM receives signals such as crankshaft position, camshaft position, engine speed, and engine coolant temperature. Then, the ECM sends ON/OFF pulse duty signals to the intake valve timing control solenoid valve depending on driving status. This makes it possible to control the shut/open timing of the intake valve to increase engine torque in low/mid speed range and output in high-speed range.

The intake valve timing control solenoid valve changes the oil amount and direction of flow through intake valve timing control unit or stops oil flow. The longer pulse width advances valve angle. The shorter pulse width retards valve angle. When ON and OFF pulse widths become equal, the solenoid valve stops oil pressure flow to fix the intake valve angle at the control position.

Symptoms
- Engine Light ON (or Service Engine Soon Warning Light)
- Possible engine lack/loss of power
- Posssible engine rough idle

Possible causes
- Harness or connectors
- Intake valve timing control solenoid valve circuit is open or shorted
- Intake valve timing control solenoid valve may be faulty
- Crankshaft position sensor (POS) may be faulty
- Camshaft position sensor

Tech notes
Since the Intake valve timing control solenoid valve uses oil flow to control timing, dirty oil can cause the valve to stuck open or close. Before replacing the valve, change engine oil and filter and reset engine code.


Hope thsis helps (remember to rate this answer).

May 11, 2011 | Nissan Maxima Cars & Trucks

1 Answer

2006 subaru forester,check engine light is on and cruise light is flashing, diagnoses code P0026


Possible causes are:-
- Dirty engine oil
- Low engine oil level
- Intake valve control solenoid circuit open or shorted
- Intake valve control solenoid circuit poor electrical connection
- Faulty intake valve control solenoid

May 02, 2011 | 2007 Subaru Forester Sports 2.5XT

1 Answer

I have a 2003 a4/b6 1.8 turbo and the engine light is on. The DTC codes says random misfire, misfire on cylinder #2 and #3 also, Oxygen (Lambda) Sensor Regulation: Bank 1: System too Lean : P1111. Any...


If you can supply me with all the codes your vehicle is showing, I can assist you. As far as the P1111 DTC goes I have listed the info below with some possible solutions.

P1111- Intake Valve Timing Control Solenoid Valve Circuit Bank 1

Intake valve timing control solenoid valve is activated by ON/OFF pulse duty (ratio) signals from the ECM. The intake valve timing control solenoid valve changes the oil amount and direction of flow through intake valve timing control unit or stops oil flow. The longer pulse width advances valve angle. The shorter pulse width retards valve angle. When ON and OFF pulse widths become equal, the solenoid valve stops oil pressure flow to fix the intake valve angle at the control position. The code is triggered when an improper voltage is sent to the ECM through intake valve timing control solenoid valve. Since the Intake valve timing control solenoid valve uses oil flow to control timing, dirty oil can cause the valve to stuck open or close. Before replacing the valve, change engine oil and filter and reset engine code.

Possible Causes:
- Intake valve timing control solenoid valve bank 1 circuit is open or shorted.
- Intake valve timing control solenoid valve bank 1 circuit connectors
- Intake valve timing control solenoid valve bank 1
- Dirty Oil

Possible Solutions:
- Change Oil
- Replace Intake valve timing control solenoid valve

Jan 20, 2011 | 2003 Audi A4 Cabriolet

2 Answers

I have my check engine light on my 2003 Ford F150 supercrew truck, with 141000 mil, engine is the v8 4.9L my temp gauge pegs out to the hot when i drive a bit and the engine light comes on i am told its a...


here are all poss causes of check engine light.
Generic Trouble Codes

P0001-P0099 – Fuel and Air Metering and Auxiliary Emission Controls

Code Description
P0001 Fuel Volume Regulator Control Circuit/Open
P0002 Fuel Volume Regulator Control Circuit Range/Performance
P0003 Fuel Volume Regulator Control Circuit Low
P0004 Fuel Volume Regulator Control Circuit High
P0005 Fuel Shutoff Valve Control Circuit/Open
P0006 Fuel Shutoff Valve Control Circuit Low
P0007 Fuel Shutoff Valve Control Circuit High
P0008 Engine Position System Performance (Bank 1)
P0009 Engine Position System Performance (Bank 2)
P0010 A Camshaft Position Actuator Circuit (Bank 1)
P0011 A Camshaft Position - Timing Over - Advanced or System Performance (Bank 1)
P0012 A Camshaft Position - Timing Over - Retarded (Bank 1)
P0013 B Camshaft Position - Actuator Circuit (Bank 1)
P0014 B Camshaft Position - Timing Over - Advanced or System Performance (Bank 1)
P0015 B Camshaft Position - Timing Over - Retarded (Bank 1)
P0016 Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor A)
P0017 Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor B)
P0018 Crankshaft Position - Camshaft Position Correlation (Bank 2 Sensor A)
P0019 Crankshaft Position - Camshaft Position Correlation (Bank 2 Sensor B)
P0020 A Camshaft Position Actuator Circuit (Bank 2)
P0021 A Camshaft Position - Timing Over - Advanced or System Performance (Bank 2)
P0022 A Camshaft Position - Timing Over-Retarded (Bank 2)
P0023 B Camshaft Position - Actuator Circuit (Bank 2)
P0024 B Camshaft Position - Timing Over - Advanced or System Performance (Bank 2)
P0025 B Camshaft Position - Timing Over - Retarded (Bank 2)
P0026 Intake Valve Control Solenoid Circuit Range/Performance (Bank 1)
P0027 Exhaust Valve Control Solenoid Circuit Range/Performance (Bank 1)
P0028 Intake Valve Control Solenoid Circuit Range/Performance (Bank 2)
P0029 Exhaust Valve Control Solenoid Circuit Range/Performance (Bank 2)
P0030 HO2S Heater Control Circuit (Bank 1 Sensor 1)
P0031 HO2S Heater Control Circuit Low (Bank 1 Sensor 1)
P0032 HO2S Heater Control Circuit High (Bank 1 Sensor 1)
P0033 Turbo Charger Bypass Valve Control Circuit
P0034 Turbo Charger Bypass Valve Control Circuit Low
P0035 Turbo Charger Bypass Valve Control Circuit High
P0036 HO2S Heater Control Circuit (Bank 1 Sensor 2)
P0037 HO2S Heater Control Circuit Low (Bank 1 Sensor 2)
P0038 HO2S Heater Control Circuit High (Bank 1 Sensor 2)
P0039 Turbo/Super Charger Bypass Valve Control Circuit Range/Performance
P0040 O2 Sensor Signals Swapped Bank 1 Sensor 1/ Bank 2 Sensor 1
P0041 O2 Sensor Signals Swapped Bank 1 Sensor 2/ Bank 2 Sensor 2
P0042 HO2S Heater Control Circuit (Bank 1 Sensor 3)
P0043 HO2S Heater Control Circuit Low (Bank 1 Sensor 3)
P0044 HO2S Heater Control Circuit High (Bank 1 Sensor 3)
P0045 Turbo/Super Charger Boost Control Solenoid Circuit/Open
P0046 Turbo/Super Charger Boost Control Solenoid Circuit Range/Performance
P0047 Turbo/Super Charger Boost Control Solenoid Circuit Low
P0048 Turbo/Super Charger Boost Control Solenoid Circuit High
P0049 Turbo/Super Charger Turbine Overspeed
P0050 HO2S Heater Control Circuit (Bank 2 Sensor 1)
P0051 HO2S Heater Control Circuit Low (Bank 2 Sensor 1)
P0052 HO2S Heater Control Circuit High (Bank 2 Sensor 1)
P0053 HO2S Heater Resistance (Bank 1 Sensor 1)
P0054 HO2S Heater Resistance (Bank 1 Sensor 2)
P0055 HO2S Heater Resistance (Bank 1 Sensor 3)
P0056 HO2S Heater Control Circuit (Bank 2 Sensor 2)
P0057 HO2S Heater Control Circuit Low (Bank 2 Sensor 2)
P0058 HO2S Heater Control Circuit High (Bank 2 Sensor 2)
P0059 HO2S Heater Resistance (Bank 2 Sensor 1)
P0060 HO2S Heater Resistance (Bank 2 Sensor 2)
P0061 HO2S Heater Resistance (Bank 2 Sensor 3)
P0062 HO2S Heater Control Circuit (Bank 2 Sensor 3)
P0063 HO2S Heater Control Circuit Low (Bank 2 Sensor 3)
P0064 HO2S Heater Control Circuit High (Bank 2 Sensor 3)
P0065 Air Assisted Injector Control Range/Performance
P0066 Air Assisted Injector Control Circuit or Circuit Low
P0067 Air Assisted Injector Control Circuit High
P0068 MAP/MAF - Throttle Position Correlation
P0069 Manifold Absolute Pressure - Barometric Pressure Correlation
P0070 Ambient Air Temperature Sensor Circuit
P0071 Ambient Air Temperature Sensor Range/Performance
P0072 Ambient Air Temperature Sensor Circuit Low
P0073 Ambient Air Temperature Sensor Circuit High
P0074 Ambient Air Temperature Sensor Circuit Intermittent
P0075 Intake Valve Control Solenoid Circuit (Bank 1)
P0076 Intake Valve Control Solenoid Circuit Low (Bank 1)
P0077 Intake Valve Control Solenoid Circuit High (Bank 1)
P0078 Exhaust Valve Control Solenoid Circuit (Bank 1)
P0079 Exhaust Valve Control Solenoid Circuit Low (Bank 1)
P0080 Exhaust Valve Control Solenoid Circuit High (Bank 1)
P0081 Intake Valve Control Solenoid Circuit (Bank 2)
P0082 Intake Valve Control Solenoid Circuit Low (Bank 2)
P0083 Intake Valve Control Solenoid Circuit High (Bank 2)
P0084 Exhaust Valve Control Solenoid Circuit (Bank 2)
P0085 Exhaust Valve Control Solenoid Circuit Low (Bank 2)
P0086 Exhaust Valve Control Solenoid Circuit High (Bank 2)
P0087 Fuel Rail/System Pressure - Too Low
P0088 Fuel Rail/System Pressure - Too High
P0089 Fuel Pressure Regulator 1 Performance
P0090 Fuel Pressure Regulator 1 Control Circuit
P0091 Fuel Pressure Regulator 1 Control Circuit Low
P0092 Fuel Pressure Regulator 1 Control Circuit High
P0093 Fuel System Leak Detected - Large Leak
P0094 Fuel System Leak Detected - Small Leak
P0095 Intake Air Temperature Sensor 2 Circuit
P0096 Intake Air Temperature Sensor 2 Circuit Range/Performance
P0097 Intake Air Temperature Sensor 2 Circuit Low
P0098 Intake Air Temperature Sensor 2 Circuit High
P0099 Intake Air Temperature Sensor 2 Circuit Intermittent/Erratic

Dec 01, 2009 | 2003 Ford F150 Regular Cab

2 Answers

P0440 Evaporative Emission Control System Malfunction P0446 Evaporative Emission Control System Vent Control Circuit Malfunction P1400 EGRC Solenoid Valve My car won't pass inspection because of...


You need a charcoal canister and vent control valve.

You also need the EGR solenoid valve (I think it the brown one).

Valve is located in the valley of the V, towards the transmission side of engine.

Do these 1st and reset light. You may have other issues but you have to start here.

Aug 02, 2008 | Nissan Maxima Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

1,034 people viewed this question

Ask a Question

Usually answered in minutes!

Top Subaru Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Subaru Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...