Question about 1988 Mazda B2200

Open Question

Where is the fuel filter on a 1989 Mazda b2200 pickup

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
Ajkill
  • 2035 Answers

SOURCE: changing fuel filter on 2002 Mazda pickup

Clean all dirt and/or grease from the fuel filter fittings. "Quick Connect" fittings are used on models equipped with a pressurized fuel system. These fittings must be disconnected using the proper procedure or the fittings may be damaged. The fuel filter uses a "hairpin" clip retainer. Spread the two hairpin clip legs about 1/8 in. (3mm) each to disengage it from the fitting, then pull the clip outward. Use finger pressure only; do not use any tools. Push the quick connect fittings onto the filter ends. Mazda recommends that the retaining clips be replaced whenever removed. The fuel tubes used on these fuel systems are manufactured in 5/16 in. and 3/8 in. diameters. Each fuel tube takes a different size hairpin clip, so keep this in mind when purchasing new clips. A click will be heard when the hairpin clip snaps into its proper position. Pull on the lines with moderate pressure to ensure proper connection. Start the engine and check for fuel leaks. If the inertia switch (reset switch) was disconnected to relieve the fuel system pressure, cycle the ignition switch from the OFF to ON position several times to re-charge the fuel system before attempting to start the engine.
0900c15280192eed.jpgRemove the "hairpin" clip retainers to access the fuel line fittingsThe inline reservoir type fuel filter should last the life of the vehicle under normal driving conditions. If the filter does need to be replaced, proceed as follows:
CAUTIONIf the fuel filter is being serviced with the rear of the vehicle higher than the front, or if the tank is pressurized, fuel leakage or siphoning from the tank fuel lines could occur. to prevent this condition, maintain the vehicle front end at or above the level of the rear of vehicle. also, relieve tank pressure by loosening the fuel fill cap. cap should be tightened after pressure is relieved.

  1. Shut the engine off. Depressurize the fuel system.
  2. Raise and support the vehicle safely.
  3. Detach the fuel lines from both ends of the fuel filter by disengaging both push connect fittings. Install new retainer clips in each push connect fitting.
  4. Note which way the flow direction arrow points on the old filter.
  5. Remove the filter from the bracket by loosening the filter retaining clamp enough to allow the filter to pass through.
The flow direction arrow should be positioned as installed in the bracket to ensure proper flow of fuel through the replacement filter.
  1. Install the filter in the bracket, ensuring proper direction of flow as noted by arrow. Tighten clamp to 15-25 inch lbs.
  2. Install the push connect fittings at both ends of the filter.
  3. Lower the vehicle.
  4. Start the engine and check for leaks.
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Properly relieve the fuel system pressure.
  3. Remove or disconnect the following:
    • Negative battery cable
    • Push connect and R-clip fittings from the fuel filter
    • Fuel filter 0900c15280192eee.jpgFuel filter location and connections–2002–2006
To install:
  1. Install or connect the following:
    • Fuel filter. Torque the nut to 17 ft. lbs. (23 Nm).
    • R-clip and push connect fittings
    • Negative battery cable
  2. Start the vehicle, check for leaks and repair if necessary.

Posted on Oct 17, 2008

Ad
jingB
  • 19 Answers

SOURCE: mazda engine bad

yes, i believe you could put any engine on your pick-up provided it is the rear wheel type set-up and the engine comes with its own tranny. problem is, if changing the engine mounts, tranny mounts, wiring set-up and exhaust system layout would not be of any problem to you. might as well look for the same mazda engine you have as a replacement to ease installation.

Posted on Apr 14, 2009

soc21610k
  • 215 Answers

SOURCE: price on a 1991 B2200 Mazda Pickup truck carburetor

Depends if you want new or used, Location, and a few other variables

Posted on Jun 04, 2009

  • 1 Answer

SOURCE: 1989 mazda b2200 can not set timing

i have a 1988 mazda b2200 and i was sittin still runnin and it was a lil low in water and i was just ab to take off when it cut off. it made steam *** out the hood. the thing is its gettin eletric to the plugs and its gettin gas and i even tried a lil eather and its turnin over it just want crank. do u have a idea wat it could b? im thinkin it jump timeing.

Posted on Feb 25, 2010

ZJLimited
  • 17970 Answers

SOURCE: i need a duagram on replacing a thermostat 1994

Mazda Trucks 1987-1993 Repair Guide
Thermostat

printpage_icon.gif

REMOVAL AND INSTALLATION

If the replacement thermostat is equipped with a &inch;jiggle pin&inch;, the pin must be install facing upwards toward the top of the engine (12 o'clock), and should be on the side facing the water outlet. When installing the thermostat gasket, the seal print side should face the cylinder head.
2.2L Engine
See Figure 1
  1. Drain enough coolant to bring the coolant level down below the thermostat housing. the thermostat housing is located on the left front side of the cylinder block.


CAUTION When draining the coolant, keep in mind that cats and dogs are attracted by the ethelyne glycol antifreeze, and are quite likely to drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantity. Always drain the coolant into a sealable container. Coolant should be reused unless it is contaminated or several years old.
  1. Disconnect the temperature sending unit wire.
  2. Remove the coolant outlet elbow.
  3. If so equipped, position the vacuum control valve out of the way. The vacuum control valve is not used on California trucks.
  4. Disconnect the coolant by-pass hose from the thermostat housing.
  5. Remove the thermostat and housing from the engine.
  6. Note the position of the jiggle pin and remove the thermostat from the housing.
  7. Remove all gasket material from the parts.
e0283c4.jpg

Fig. 1: Thermostat installation

To install:

  1. Position the thermostat in the housing with the jiggle pin up. Coat a new gasket with sealer and install it on the thermostat housing.
  2. Install the thermostat housing using a new gasket with water resistant sealer. Tighten the bolts to 14-19 ft. lbs. (19-25 Nm).
  3. Install the coolant outlet elbow and vacuum control valve (if equipped).
  4. Connect the by-pass and radiator hoses.
  5. Connect the temperature sending unit wire.
  6. Fill the cooling system with the proper coolant. Operate the engine and check the coolant lever. Check for leaks.

Hope helps with this (remember rated this).

Posted on May 30, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1990 mazda b2200 2.2l fuel injected won't accelerate just bogs down idles fine


I think you have established that it is getting fuel but I guess what I would do is check into the throttle body itself.

May 20, 2014 | 1988 Mazda B2200

1 Answer

I have an 1989 mazda b2200 pickup it just started blowing fuses every time i turn on my park lights.


check tail & park light circuits for short to ground. best place to start is at trailer wiring harness. (if equiped) i might want to purchase a "short finder" tool. (fairly cheap at harbor freight.) to help locate area of short. good luck.

Oct 21, 2011 | 1988 Mazda B2200

1 Answer

How do i lower the spare tire on 1989 Mazda b2200 pickup?


will need the original wheel tools is about 4 foot long with hook on one end and square solid tool joint on the other which takes the handle supplied. go to the rear of the vehicle and insert the tool into the slot on top of the spare wheel and wind anti clockwise until the wheel is onthe ground

Jul 27, 2010 | 1988 Mazda B2200

1 Answer

I have a 1989 Mazda b2200 and I need to change the fuel filter how do I do that?


Its pretty simple, just 2 hoses to take off, and put them on the new filter.

May 08, 2010 | 1988 Mazda B2200

1 Answer

How to quiet noisey lifters


replace lifters or run diesel fuel thru engine at next oil change to remove sludge and coating on lifters

Mar 03, 2010 | 1988 Mazda B2200

2 Answers

1989 mazda b2200 can not set timing


i have a 1988 mazda b2200 and i was sittin still runnin and it was a lil low in water and i was just ab to take off when it cut off. it made steam *** out the hood. the thing is its gettin eletric to the plugs and its gettin gas and i even tried a lil eather and its turnin over it just want crank. do u have a idea wat it could b? im thinkin it jump timeing.

Feb 17, 2010 | 1988 Mazda B2200

1 Answer

My 1992 Mazda B2200 Pickup doesn't heat the cab anymore


feel heater core to see if it is getting and staying hot when fan is on, if not could be obstruction in heater core or valve

Oct 09, 2009 | 1989 Mazda 323

1 Answer

1988 Mazda B2200 starts well, but as it warms up, the gas flow stops. I changed the fuel pump and the problem still persists. Always starts.


I would trying to either checked fuel filter or if that dosent work chang the fuel pressure regulator.

Jul 19, 2009 | 1988 Mazda B2200

1 Answer

Price on a 1991 B2200 Mazda Pickup truck carburetor


Depends if you want new or used, Location, and a few other variables

Jun 04, 2009 | 1988 Mazda B2200

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

223 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...