Question about Pontiac Grand Prix

Open Question

How to remove the front seats on 1997 Pontiac grand prix

Front driver seat is power operated

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: 2001 jeep grand cherokee seat removal

i actually removed my 2 front seats very easily as a novice. There really is only i think 4 bolts that need to come out 2 in front and 2 in back. If i can remember correctly i believe it was a larger metric size. Although i dont have power seats, if you do just look for the clip connector and disengage

Posted on Jul 07, 2008

  • 5 Answers

SOURCE: srs airbag light is on on my 99 pontiac grand prix

If the seat belt light comes on intermittently with the belt buckled, it may have a bad switch in the buckle or a loose connection @ the switch. This may also set a diagnostic trouble code in the srs control module & keep the srs airbag light on.

Posted on Mar 27, 2009

  • 1 Answer

SOURCE: 1997 PONTIAC GRAND AM

firewall corroded and perforated like mine had to remove entire dash to repair

Posted on Apr 15, 2009

ZJLimited
  • 17970 Answers

SOURCE: how do i remove the front seats of a 1998 Pontiac

On W-Body vehicles, the front seats are secured to the floorpan by two front hook attachments and two rear bolts installed to nuts welded to the floorpan.
The manually operated two-way front adjusters provides only fore and aft movement of the seat. When the seat adjuster handle located on the front seat is pulled up, the seat adjusters unlock, permitting travel of the seat. When the seat is in the desired position and the seat adjuster handle is released, the seat locks in place.
A power operated six-way seat adjuster is available. The adjusters are activated by three 12 volt, reversible, permanent magnet motors with a built-in circuit breaker. The motors are energized by a switch bolted on the seat side panel.
The three motors drive the front seat and rear vertical actuators and a horizontal actuator. When the adjusters reach the limit of travel, torque is absorbed through the rubber mounted grommets located between the motor and the support. An overload relay is provided in the circuit and will open should excessive stall be applied.
The optional 60/40 split bench front seats have seat back head restraints on the driver's and passenger's seat back. The head restraints are designed so they cannot be removed from the seat back without first inserting a small rounded tool inside the head restraint support tube to release the locking tab. The 60/40 split bench seat is equipped with a reclining mechanism on both the driver's and passenger's side. The recliner lever is located on the outboard side of the spring cushion. When the lever is pulled upward, the spring loaded dual linear reclining unit located in the cushion frame is released, allowing the seat back to be pushed rearward or allowing the spring loaded reclining unit to bring the seat back forward.
Bucket seats are equipped with manual reclining mechanisms. An optional six-way power seat adjuster is available. Some bucket seats are equipped with inertia seat back locks. This system allows the seat back to fold forward without requiring the occupant to release a locking lever or access to the rear seat area. During a sudden stop or deceleration, or if the front of the vehicle is nose down, the inertia system of the seat back lock will engage, holding the seat back in its rest position. A release lever is provided to allow manual release of the seat back lock when the vehicle is in the nose down position. The release lever is located at the lower rear outboard corner of the seat back.
Some W-Body vehicles (notably Pontiac coupes) have passenger front seats equipped with an E-Z Entry device. This is actuated, in an unoccupied seat, by completely folding the seat back forward disengaging the adjuster, and sliding the front seat forward to gain access to the rear seat area. To return the seat to its normal position, return the seat back to its rest position, and slide the entire seat rearward, engaging the adjuster.
W-Body rear seats are available in several styles including a rear seat with an integral child restraint device.

Posted on Sep 01, 2009

  • 163 Answers

SOURCE: front seat removal - 2004 pontiac GTO

Unplug and unbolt them nothing special.

Posted on Sep 18, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can't remove driver front seat of Pontiac grand prix 06 as the seat is stuck all the way back and I don't have access to the rear bolts


you have to use an open end wrench and go under the seat at the back-a good job for a contortionist-cheers Denny

Nov 01, 2013 | Cars & Trucks

1 Answer

Can I replace my 98 grand prix driver's seat with


You can replace it as long as the one you are replacing is the same set-up. If you have a manual adjusting seat and replace it with a power seat it will fit but you wont have the hook ups for it. Also make sure if it is a bucket seat (single person) you dont replace it with a bench (3 persons fit in front) seat or you will run into problems with the center console and shifter. vice versa may bolt up but there will be a gap between the 2 front seats

Nov 22, 2011 | 1998 Pontiac Grand Prix

1 Answer

I need to now how to take the driver and passanger seats out of a 1997 pontiac grand prix


There are four bolts that mount them to the body, you might have to move the seat forwards or backwards in order to access them. You'll need a ratchet and I believe a 1/2 inch socket. Also you'll need to unplug the electrical connection if there powered seats.

Aug 31, 2010 | 1997 Pontiac Grand Prix

1 Answer

I have a 2000 Pontiac Grand Prix se. Both the drivers side windows will not go up/down. I removed the rear door panel of both doors and the small metal cable has come off. Is there a diagram or a fix to...


I had a problem similar to this but mine was in a GT and they would just work when they wanted to. I just had all the wires cut leading to the front passenger seat, back driver seat, and back passenger seat. And left the wires on the main. They all work perfect now. But the downside is that the driver is the only one who can put the windows down. (Which isn't always a bad thing) Hope I could help!

Jul 01, 2010 | 2000 Pontiac Grand Prix

1 Answer

Stuck seat belt


Remove the panels to the belt, normally these can miss roll and get stuck. Unbolt the unit so you can get some slack that should be enough to release and pull it back out to correct it. If that will not do it get a replacement from a junkyard and replace.

May 20, 2010 | 1990 Pontiac Grand Prix

2 Answers

How do you take out the front seats on a 2004 grand prix gt?


You will need to crawl under the vehicle. The bolts holding them down are located there. You may need two people. One to hold the bolt secure insde the car and one to turn the bolt from underneith. There maybe as many as 6 bolts per seat. I am assuming these are bucket style seats. Tell me how it turns out, Raz

Apr 18, 2010 | 2004 Pontiac Grand Prix

1 Answer

Is there a manual override for the electric seat in a 2000 Pontiac Grand Prix? the seat is forward and won't go back


No its electric only. Check the fuse first. If the fuse is good, check to see the seat controls are getting power. If power is at the controls, check to see if power is available at the seat motor. If there is then the seat motor is bad.

Jan 15, 2010 | 2000 Pontiac Grand Prix

1 Answer

2003 pontiac grand prix power seat will not go forward or backward but it will go up and down


Check the connector on the cylindrical motor under the seat. You can see it from the back seat well. The connector has a tendency to come loose because of stuff pushed underneath the seat.

Dec 28, 2009 | 2003 Pontiac Grand Prix

1 Answer

How do i remove the front seats of a 1998 Pontiac Grand Prix?


On W-Body vehicles, the front seats are secured to the floorpan by two front hook attachments and two rear bolts installed to nuts welded to the floorpan.
The manually operated two-way front adjusters provides only fore and aft movement of the seat. When the seat adjuster handle located on the front seat is pulled up, the seat adjusters unlock, permitting travel of the seat. When the seat is in the desired position and the seat adjuster handle is released, the seat locks in place.
A power operated six-way seat adjuster is available. The adjusters are activated by three 12 volt, reversible, permanent magnet motors with a built-in circuit breaker. The motors are energized by a switch bolted on the seat side panel.
The three motors drive the front seat and rear vertical actuators and a horizontal actuator. When the adjusters reach the limit of travel, torque is absorbed through the rubber mounted grommets located between the motor and the support. An overload relay is provided in the circuit and will open should excessive stall be applied.
The optional 60/40 split bench front seats have seat back head restraints on the driver's and passenger's seat back. The head restraints are designed so they cannot be removed from the seat back without first inserting a small rounded tool inside the head restraint support tube to release the locking tab. The 60/40 split bench seat is equipped with a reclining mechanism on both the driver's and passenger's side. The recliner lever is located on the outboard side of the spring cushion. When the lever is pulled upward, the spring loaded dual linear reclining unit located in the cushion frame is released, allowing the seat back to be pushed rearward or allowing the spring loaded reclining unit to bring the seat back forward.
Bucket seats are equipped with manual reclining mechanisms. An optional six-way power seat adjuster is available. Some bucket seats are equipped with inertia seat back locks. This system allows the seat back to fold forward without requiring the occupant to release a locking lever or access to the rear seat area. During a sudden stop or deceleration, or if the front of the vehicle is nose down, the inertia system of the seat back lock will engage, holding the seat back in its rest position. A release lever is provided to allow manual release of the seat back lock when the vehicle is in the nose down position. The release lever is located at the lower rear outboard corner of the seat back.
Some W-Body vehicles (notably Pontiac coupes) have passenger front seats equipped with an E-Z Entry device. This is actuated, in an unoccupied seat, by completely folding the seat back forward disengaging the adjuster, and sliding the front seat forward to gain access to the rear seat area. To return the seat to its normal position, return the seat back to its rest position, and slide the entire seat rearward, engaging the adjuster.
W-Body rear seats are available in several styles including a rear seat with an integral child restraint device.

Sep 01, 2009 | 1998 Pontiac Grand Prix

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

134 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...