Question about Cars & Trucks

Open Question

Where is the IAT sensor on a L67 supercharged VX commodore

L67 supercharged engine

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
jimmymac725
  • 34 Answers

SOURCE: IAT sensor

The IAT has been integrated with the MAF and cannot be accessed seperatley,

Jim

Posted on Oct 09, 2008

Ad
Molson02536
  • 3854 Answers

SOURCE: cnt find iat sensor on 2005 chevy cobalt ss supercharged

The IAT sensor is most of the time located along the intake tube right after Between the throttle body and MAP sensor. Just follow your air intake tube from your air filter housing to the Throttle body.
Good luck. 

Posted on Apr 10, 2009

Molson02536
  • 3854 Answers

SOURCE: locating the iat sensor on a 2003 dodge 5.9

The IAT sensor is along the intake tube before the throttle body. If your planing to buy the performance chip from EBAY or any other place, save your money. You can go to Radio shack and it will cost you less then $3.00 for the resistor needed to make your own "performance Chip" IF you like you can use and 10K ohm potentiometer wire it through to the IAT sensor wire harness so you can adjust your timing for the type of fuel you want to use or how much performance you want out of your engine. Here is a link to the installation of the resistors and the different resistor's you can use or like me use a Potentiometer. Note if the timing is to high on hot days, the knock sensor may trigger and the engine will power down 15% till next start up. Good luck and hope this helps. http://kingenterprises.net/IAT-Timing-Tricker.htm

Posted on Jun 15, 2009

  • 107 Answers

SOURCE: code came back as iat sensor reading high

the iat sensor is located either in the air cleaner housing or in the ducting that goes from the air cleaner to the throttle body

Posted on Jul 15, 2009

  • 408 Answers

SOURCE: code came back as iat sensor reading high

IAT stands for Air Intake Temperature Sensor and it is located in the intake tube coming from the air filter box tot he engine. Easiest way to find it is look at the top of your engine where it says 2200. Coming right out of that manifold is a black ribbed tube about the size of a baseball to softball. It should be going towards the direction on the front drivers side. on the back side of that tube, about 4 inches away from the intake manifold (the things that says 2200) is a plug with wires. That is your IAT Sensor. If it is unplugged, plug it back in. Otherwise unplug it and replace it. Make sure to disconnect the battery while you do this so the computer resets itself after the new one is installed. Thanks and please don't forget to rate!

Posted on Jul 15, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Wat kind of v8 is suitable for a 1997 3.8 v6 holden commodore excutive


your VT /VX came out with a V8 engine
you need the engines ECU and the V8 gearbox
manual diff ratios can be optional

1997 -2002 engines will bolt in

you could go up the next commy V8 model it has roller rockers
you can have a v6 or v8 supercharged if you like

once all bolted in you need a mutt 2 diagnostic reader to reset all the keys and modules and immobilizer for it to start and run

http://forums.justcommodores.com.au/vt-vx-holden-commodore-1997-2002





26317726-igf4vixkefavsop0s5kuy20y-4-0.jpg

26317726-igf4vixkefavsop0s5kuy20y-4-1.jpg

26317726-igf4vixkefavsop0s5kuy20y-4-3.jpg

Oct 19, 2016 | Holden Cars & Trucks

1 Answer

Will ls1 go in vx commodore s 2000


yes VX V8s were fitted
depends on what state you live in
LS1 fitted may need a modification plate
needs the LS1 engine ecu and
and a few extra wiring and
join the just commodore forum for loads of helpful information
http://forums.justcommodores.com.au/vt-vx-holden-commodore-1997-2002

Jul 29, 2016 | Cars & Trucks

1 Answer

Vacuum diagram wh L67 1999 holden statesman ?


I've just put L67 vacuum lines into "images" on bing and got all sorts of pictures, start there?

Nov 15, 2014 | Cars & Trucks

2 Answers

What is the vaccume routing on a 98 statesman with factory supercharged engine.


Go to library and see if they have repair manual for this car. Otherwise buy one at dealer.

Jun 29, 2014 | Holden Caprice Cars & Trucks

1 Answer

How does the vaccume routing go on the L67 supercharged v6 if at all possible a diagram would be great thank you


first off , vacuum lines vary by engine. and country
in 1992 there are many SMOG vacuum lines that vary by the laws of your country, .
IS this a HOLDEN CAR, WITH l67 ENGINE>? 1992.
the only way to get this is at HOLDEN and buy the FSM.
sure way.
Down under you are, right>? land of AUZ./

Jun 29, 2014 | 1992 Holden VQ Statesman

1 Answer

Transmission Compatibility


As you see I provided you the models you can apply the transmission :The 4T65E-HD (code MN7) is a heavy duty version of the 4T65-E used with more powerful engines such as the LS4 V8 and L67/L32 supercharged V6. Applications: 2.93:1 MN7 Pontiac Bonneville SSEi L67 Chevrolet Impala L67 Chevrolet Monte Carlo L67 Pontiac Grand Prix GTP/GXP Buick Regal GS Buick Riviera L67 (97-99) So ,yes you can!

May 28, 2013 | 1998 Pontiac Grand Prix

1 Answer

How to put on the serpentine belt


Hello! I'm not sure if you have the supercharged, or non-supercharged version of the 3.8 liter V6 - so I've posted both for you.

Supercharged L67 motor - Supercharger belt:



5d6b27a.gif

Supercharged L67 motor - Accessory drive belt:

661b42d.gif

Non-Supercharged L36 motor:


c9c9d7b.jpg

Hope this helps, and thanks for using FixYa!

-KCGTODAD

Feb 02, 2010 | 1997 Pontiac Bonneville

1 Answer

Drive belt diagram


Hello! I'm not sure if you have a N/A or Supercharged 3.8 - so I've put both diagrams below.
You'll need a 15mm wrench to move the tensioner pulley.

SE, GT models with 3.8:

9f42718.jpg
97-03 with L67 (Supercharged)

Accessory drive belt:

6dda6e1.gif
Supercharger belt:


89a45fe.gif



Hope this helps. Thanks for using FixYa!

Oct 14, 2009 | 1997 Pontiac Grand Prix

1 Answer

What car share 1997 grand prix parts


97 Grand Prix has an L36 Engine if N/A, L67 if Supercharged

Transmission is a 4T65E (-HD if supercharged)

Buick Regals, and Monte Carlo's share the powertrain and driveline along with a handful of other vehicles.

Jun 06, 2009 | 1997 Pontiac Grand Prix

1 Answer

Cnt find iat sensor on 2005 chevy cobalt ss supercharged


The IAT sensor is most of the time located along the intake tube right after Between the throttle body and MAP sensor. Just follow your air intake tube from your air filter housing to the Throttle body.
Good luck. 

Apr 09, 2009 | 2005 Chevrolet Cobalt

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

66 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

77514 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14398 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...