Question about 2008 Chevrolet Impala

1 Answer

Engine oil pressure low turn off engine - 2008 Chevrolet Impala

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 14,036 Answers

Change engine oil and oil filter,if oil pressure light still come on,check engine oil pressure should be 30 - 45 psi @ 1850 rpm for the 3.5 and 3.9 engine for the 5.3 engine oil pressure should be 18 psi. @ 2000 rpm.if oil pressure okay, more likely oil pressure sending unit faulty.if oil pressure is low you have faulty oil pump,worn engine bearings.damage camshaft oil pump drive gear.

Posted on Feb 07, 2012

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: Reset my engine oil low in 2007 chevy impala

you sould be able to reset that from the dash ,these options beside the dash go to the end and when you get to oil and % press on the checkmark and that would do the trick.

Posted on Jul 18, 2009

  • 335 Answers

SOURCE: like 3 days after i got my oil changed in my 2006

This is an idication of a severe oil leak. Check the oil level in your engine to see if there is any in it. Add to the full mark and return to the oil change shop and ask them to see where the leak is. Do not operate without oil. Severe engine damage will occur. Hope this helps Moe

Posted on Apr 28, 2009

  • 49 Answers

SOURCE: ticking noise and low oil pressure

DOES IT HAVE A LOT OF MILES ON IT OR MAY BE THE OIL PUMP IS IS GOING OUT? THERE IS A SPRING IN THE PUMP THAT IS A BYPASS FOR HOW HIGH PSI IT MAY HAVE BROKE THAT WILL GIVE YOU LOW PSI.

Posted on Jan 18, 2009

  • 118 Answers

SOURCE: Have a 1999 Z71 chev truck with 5.3 L engine that

In some cases where the oil is not changed properly, the oil pump screen maybe plugging or your oil filter is defective. Fram is a good filter. If there is no problem found, replace the pressure sensor.

Posted on Jul 27, 2009

muntejaya
  • 10421 Answers

SOURCE: The "low oil pressure -

It could be. The best is just follow your instruction manual on what type the oil should used on your car. But since your car is has the year 2006, it should use specs. API... SL or SM. The viscosity will has range 5W30 -10W40. Again don't get be cheated by the newest oil products, The best oil for your car is the one recommended on your manual in many aspects.
Regards, Jay

Posted on Feb 06, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the oil sending unit on a 1996 mercury cougar xr7 ? Its cause my oil pressure gauge is bouncing up and down...i dont know why...can anybody please help me thank you so much


26147240-wuoh52pvdxpwqpeytk4hf153-3-0.gif
The low oil pressure warning lamp will illuminate anytime the ignition switch is turned to the ON position without the engine running. When the engine is running, the light also illuminates if the engine oil pressure drops below a safe oil pressure level. To test the system, perform the following:
If the oil pressure light does not work, perform the following:
  1. Turn the ignition switch to the ON position.
  2. If the lamp does not light, check for a broken or disconnected wire around the engine and oil pressure sending unit switch.
  3. If the wire at the connector checks out OK, pull the connector loose from the switch and, with a jumper wire, ground the connector to the engine.
  4. With the ignition switch turned to the ON position, check the warning lamp. If the lamp lights, make sure the oil pressure switch is properly grounded in the cylinder block, and if so replace the oil pressure switch. If the lamp still fails to light, check for a burned out lamp or disconnected socket in the instrument cluster.
To diagnose an oil pressure light that stays on, perform the following:
  1. Check the engine oil level and top off as necessary. If the engine was 2 or more quarts low on oil, test start the engine after topping off the oil level and recheck the oil pressure light operation. If the light stays on, stop the engine immediately and go to the next step.
  2. Disconnect the wire at the sending unit, then turn the ignition switch to theON position. If the light remains on, check the wire from the sending unit to the gauge for being shorted to ground and repair as necessary. If the light goes out, turn the ignition switch OFF and go to the next step.
  3. Replace the oil pressure sending switch with a known good switch.
  4. Start the engine and check the oil pressure light operation. If the light stays on with the engine running, stop the engine immediately to avoid severe engine damage until the cause of the problem can be determined.

WARNING
If the oil pressure light remains on while the engine is started, stop the engine immediately. Do not operate the engine until the cause of the problem can be determined. Operating an engine with low oil pressure will cause severe internal damage.

Possible causes for an oil pressure light to stay on are:


Pinched or grounded sensor wireDefective oil pressure sending unitRestricted or severely leaking oil filterExcessive internal engine bearing clearance.Insufficient or severely contaminated engine oilBlocked oil pump pickup screen or severely worn oil pump

Mar 31, 2016 | Mercury Cars & Trucks

1 Answer

Has 358000 miles, just had leaks repaired. Twice since my oil pressure gauge reads no pressure but not all the time? Why


1. Oil Pressure Gauge Not Working You will notice this happens when your oil pressure gauge is not reading, whether the engine is turned off, idle or running. Try to step on the gas to rev up the engine. If the oil pressure gauge still doesn't change its reading, your gauge is busted. It's best to replace it as soon as possible because you won't have any idea if your car is already overheating or not.
2. Oil Pressure Gauge Reading Too Low When your engine is idle, the oil pressure gauge will have a low reading. When the engine starts running or when you're already cruising or on the freeway, your gauge's reading should have increased. If it stays on a low reading, then you now your oil pressure gauge is broken.
3. Oil Pressure Gauge Reading Too High Another common oil pressure gauge problem is when your oil pressure gauge is reading too high when your engine is idle or when it's turned off. Rep

Oct 24, 2015 | 2001 GMC Yukon XL

1 Answer

What does it mean when the message "STOP ENGINE, Oil pressure low on a 2007 impala


it means the oil pressure is low and may be low enough to damage the engine if you keep drving/running the engine. it would help if you could tell us the actual oil pressure, engine and mileage . basically, the oil pressure may be low enough to wreck your engine, then again it may be bs......

Mar 30, 2013 | 2007 Chevrolet Impala LS Sedan New Cars

1 Answer

Low presure oil


first thing check is the engine oil level.if oil level okay check oil pressure should be for the 4.2 engine oil pressure should be 12 psi @ 1200 rpm for the 5.3 oil pressure should be 18 psi @ 2000 rpm if oil pressure good problem in the oil pressure sending unit. if oil pressure is low problem faulty oil pump or worn crankshaft bearings if oil pressure low engine will have rod knock.make sure you are using correct oil viscosity if oil too thick you will have low oil pressure oil too thin you will loose oil pressure.

Nov 26, 2012 | 2004 GMC Envoy

2 Answers

Oil gauge drops low at idle


Low oil pressure at idle can be caused by an engine with worn rod or main bearings due to (usually) high mileage . This however does not mean the engine is still not serviceable as long as the oil pressure is low only at idle. The pressure should at minimum get into the normal range at anything above idle speed.Not much oil pressure is really necessary at LOW speed. At low speed, as long as there is oil getting to the bearings, even at low pressure, you are OK. In a high mileage engine the oil pressure is often low at idle simply because the oil pump is turning slowly and cannot maintain higher pressure between the larger than normal crankshaft and bearing clearances. As speed increases the pump turns faster and supplies more oil and the pressure should go higher. Low pressure as long as it is only at idle is not a problem. However at higher speeds the pressure should be in the normal range. Such a worn engine can benefit from higher viscosity (thicker) oil such as 20W-50 in above freezing weather and 10W-40 in winter. That will increase idle pressure and the thicker oil film maintains a better film between the worn parts

Apr 08, 2012 | 2002 Jeep Grand Cherokee

5 Answers

Whats the purpose of an oil pressure switch can it determine weather oil leaks from your grand prix or not?


The oil pressure switch or sending unit is a unit that receives an electrical signal showing what your cars oil pressure is.And yes it does partially does let you know when there is a problem somewhere in the oil system.For example if your filter gets clogged up your oil pressure will go down and then go up when you accelerate.If there was a leak in the system first you would probably see the leak And if the oil pump or oil pump shaft were to break you would have no oil pressure.So you can see the importance of having an oil pressure switch.I feel there are 2 guages that are important to watch are your oil guage and water temp guage they can tell you allot about how your car is operating.

Feb 09, 2011 | 1997 Pontiac Grand Prix

1 Answer

How do I check and possibly replace the engine oil pressure sensor in a 2006 GMC Envoy Denali?


Oil Pressure Test Check for proper oil pressure at the sending unit passage with an externally mounted mechanical oil pressure gauge. A tachometer may also be needed, as some specifications may require running the engine at a specific RPM.
  1. While the engine is cold, locate and remove the oil pressure sending unit.
  2. Following the manufacturer's instructions, connect a mechanical oil pressure gauge and, if necessary, a tachometer to the engine.
  3. Start the engine and allow it to idle.
  4. Note and record the oil pressure reading when the engine is cold. The engine may need to run at a specified RPM, if so check the vehicle's specification.
  5. Run the engine until normal operating temperature is reached.
  6. Check the oil pressure reading again with the engine hot and record the value. Turn off the engine.
Compare the hot oil pressure reading to the specification. If the reading is low, check the cold pressure reading against the specification. If the cold pressure is well above the specification, and the hot reading was lower than the specification, the engine may have the wrong viscosity oil. Change the oil, making sure to use the proper grade and quantity, and then repeat the test.
Low oil pressure readings could be attributed to internal component wear, pump related problems, a low oil level, or oil viscosity that is too low. High oil pressure readings could be caused by an overfilled crankcase, too high of an oil viscosity or a faulty pressure relief valve.

Oct 09, 2010 | 2006 GMC Envoy Denali

2 Answers

Low oil pressure no start


CHECK ENGINE OIL LEVEL ON OIL DIP STICK.OIL LEVEL SHOULD BE ON FULL MARK IF NOT ADD OIL UNTIL YOU GET TO FULL MARK.IF OIL LEVEL OKAY.YOUR LOW OIL PROBLEM CAUSED BY WORN DAMAGED OIL PUMP OR WORN ENGINE CRANKSHAFT BEARINGS.IF OIL HAS NOT BEEN CHANGED A LONG TIME CHANGE OIL AND OIL FILTER NOT GUARANTEE TO FIX PROBLEM.BUT COULD BE MINOR THING.OIL FILTER COULD BE STOPPED UP.WEAKEN OIL FLOW BUT LIKE I SAID PROBLEM COULD BE OIL PUMP OR ENGINE BEARINGS.REMOVE OIL SENDING UNIT SCREW IN A OIL PRESSURE GAUGE.TURN ENGINE OVER SEVERAL REVOLUTIONS TO SEE IF OIL PRESSURE BUILD UP TO 40 LBS. SEE 40 - 60 PSI. 2000 RPM.IF NO OIL PUMP TO WEAK .IF OIL PRESSURE RISES WHEN TURN ENGINE OVER.I HAVE SEEN FAULTY OIL PRESSURE SENDING KEEP ENGINE FROM RUNNING BECAUSE OIL PRESSURE SENDING UNIT WILL DISABLE FUEL PUMP RELAY TO KEEP FROM DAMAGING THE ENGINE.

Sep 23, 2010 | 2003 Lincoln Navigator

1 Answer

Where is the oil pressure sensor located on a 1996 murcury cougar


Look for the oil pressure sending unit on the block or the cylinder head on the V-6 or V-8 models. --- OIL PRESSURE TEST Check for proper oil pressure at the sending unit passage with an externally mounted mechanical oil pressure gauge (as opposed to relying on a factory installed dash-mounted gauge). A tachometer may also be needed, as some specifications may require running the engine at a specific rpm.
  1. With the engine cold, locate and remove the oil pressure sending unit.
  2. Following the manufacturer's instructions, connect a mechanical oil pressure gauge and, if necessary, a tachometer to the engine.
  3. Start the engine and allow it to idle.
  4. Check the oil pressure reading when cold and record the number. You may need to run the engine at a specified rpm, so check the specifications.
  5. Run the engine until normal operating temperature is reached (upper radiator hose will feel warm).
  6. Check the oil pressure reading again with the engine hot and record the number. Turn the engine OFF.
  7. Compare your hot oil pressure reading to specification. If the reading is low, check the cold pressure reading against the chart. If the cold pressure is well above the specification, and the hot reading was lower than the specification, you may have the wrong viscosity oil in the engine. Change the oil, making sure to use the proper grade and quantity, then repeat the test. Low oil pressure readings could be attributed to internal component wear, pump related problems, a low oil level, or oil viscosity that is too low. High oil pressure readings could be caused by an overfilled crankcase, too high of an oil viscosity or a faulty pressure relief valve.

Sep 09, 2010 | 1996 Mercury Cougar XR7

1 Answer

Getting a "Low Oil Pressure" message on the dash board.."Turn off engine" any ideas of what the problem might be?


Hi. This issue has several causes, but the oil light indicator is a strong sign of low pressure in the engine. This will cause the engine lubrication rate to drop, thus, producing a illuminated oil light, and erratic Oil pressure readings. The necessary actions are to have a manual oil pressure test ran on this engine, asap. When running a manual oil pressure test, you will discover if the true oil pressure is low, or normal. If the test proves that the oil pressure is, indeed, low, this will confirm that the Oil pump is suspect.

Now, if the true readings given during the manual oil pressure test are indicating that the pressure is normal, this will be the result of a failed sending unit(oil pressure switch).

Jan 11, 2010 | 2003 Chevrolet TrailBlazer

Not finding what you are looking for?
2008 Chevrolet Impala Logo

2,070 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8522 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...