Question about 2002 Hyundai Santa Fe

Open Question

How to remove ignition interlock system by yourself

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

94 merc grandmarkee wont go into park wont start will start if you wiggle in nutral


Park neutral safety switch could be bad , also the shift interlock safety system .
Shift Interlock System A brake/shifter interlock system consists of the following:
  • ignition switch (11572)
  • brake pedal stoplight switch (13480)
  • brake shift interlock module
  • brake shift interlock solenoid assembly (attached to key interlock assembly)
  • necessary wiring
On floor-shift vehicles, the ignition/shifter interlock cable (3F719):
  • locks the floor shift transaxle range selector lever in the PARK position when the ignition switch is in the LOCK position.
  • requires the floor shift transaxle range selector lever to be in the PARK position to turn the ignition switch to the LOCK position.
Condition Possible Source Action
  • Shift Interlock System Does Not Release or Lock Properly
  • Circuitry open/shorted.
  • Blown fuse.
  • Damaged stoplight switch.
  • Damaged shift lock actuator.
  • GO to Pinpoint Test A .

PINPOINT TEST A: SHIFT INTERLOCK SYSTEM DOES NOT RELEASE OR LOCK PROPERLY A1 CHECK ELECTRON IGN FUSE
  • Check Fuse 5 (5A) located in fuse junction panel.
Is fuse OK?
Yes No GO to A3 . GO to A2 . A2 CHECK FOR SHORT TO GROUND
  • Turn ignition switch OFF.
  • Remove Fuse 5 (5A).
  • Disconnect shift-lock actuator connector C203 located to the right of steering column.
  • Measure resistance of the Circuit 1003 (GY/Y) between the correct terminal of Fuse 5 (5A) and ground.
Is resistance greater than 10,000 ohms?
Yes No REPLACE Fuse 5 (5A). GO to A3 . SERVICE Circuit 1003 (GY/Y) wire between fuse junction panel and shift-lock actuator. A3 CHECK POWER SUPPLY FROM FUSE 5 (5A)
  • Reinstall Fuse 5 (5A).
  • Turn ignition switch to RUN.
  • Measure voltage on Circuit 1003 (GY/Y) wire and ground.
Is voltage greater than 10 volts?
Yes No GO to A4 . SERVICE Circuit 1003 (GY/Y) wire between interior fuse panel and shift-lock actuator. A4 CHECK POWER SUPPLY FROM FUSE 28 (15A)
  • Turn ignition switch OFF.
  • Disconnect connector C2016.
  • Turn ignition switch ON.
  • Measure voltage on Circuit 10 (LG/R) and ground.
Is voltage B+?
Yes No GO to A5 . SERVICE Circuit 10 (LG/R) for open. RESTORE vehicle and RETEST system. A5 CHECK WIRE BETWEEN STOPLIGHT SWITCH AND SHIFT-LOCK ACTUATOR
  • Turn ignition switch OFF.
  • Disconnect shift-lock actuator connector C203.
  • Apply brake pedal.
  • Measure voltage on Circuit 810 (R/LG) wire and ground.
Is voltage greater than 10 volts with brake pedal applied and less than 1 volt with brake pedal released?
Yes No GO to A6 . SERVICE Circuit 810 (R/LG) wire between stoplight switch and shift-lock actuator. A6 CHECK SHIFT-LOCK ACTUATOR GROUND
  • Measure resistance of Circuit 57 (BK) and ground.
Is resistance less than 5 ohms?
Yes No REPLACE shift-lock actuator. SERVICE BK wire.

Mar 30, 2017 | Cars & Trucks

1 Answer

Transmission won't shift into gear only park works no prior problems just all of a sudden stop Lincoln Continental 2001


I would say it has something to do with this !
Shift Interlock System An ignition/shifter interlock mechanism is installed to prevent shifting the transaxle out of the PARK position unless the ignition switch is rotated to RUN and the brake pedal is applied. The floor shift interlock system consists of:
  • an actuator assembly integral to the ignition/shifter interlock cable assembly.
  • a bracket retaining the actuator.
  • the necessary wiring.
The solenoid is energized when the ignition switch is turned to the RUN position, locking the transaxle range selector lever in the PARK position. When the brake pedal is applied and the stoplight switch (13480) is activated, the ignition/shifter interlock actuator is deactivated and the transaxle range selector lever can be moved out of the PARK position.

Dec 17, 2016 | 2001 Lincoln Continental

1 Answer

Where is the brake shift interlock solenoid?


Brake/Shift Interlock System The shift interlock system prevents the shifting from PARK (P) (when the ignition switch is in the RUN position) unless the brake pedal (2455) is depressed. The interlock system consists of an electrical solenoid mounted at the base of the steering column (3C529). If the ignition switch is in the RUN position, the solenoid has continuous power supplied unless the brake pedal is depressed.

Removal
  1. Remove steering column as outlined in Section 11-04A or Section 11-04B .
  1. Unclip wire terminal from solenoid.
  1. Remove insert plate and solenoid by removing three retaining screws.
  1. Pry off clip.

Installation
  1. NOTE: The clip which retains the solenoid to the insert plate should not be replaced for service. The clip's sole purpose is an assembly aid for the assembly plant. Position insert plate/solenoid assembly to the steering column and tighten the retaining screws.
  1. Install the steering column in the vehicle as described in Section 11-04A or Section 11-04B .

Feb 09, 2016 | 1996 Ford Ranger SuperCab

1 Answer

The linkage are hooked up but the car still want go into park,a 2000 Taurus


Do you have floor console shifter ?
Shift Interlock System A brake/shifter interlock system consists of the following:
  • ignition switch (11572)
  • brake pedal stoplight switch (13480)
  • brake shift interlock module
  • brake shift interlock solenoid assembly (attached to key interlock assembly)
  • necessary wiring
On floor-shift vehicles, the ignition/shifter interlock cable (3F719):
  • locks the floor shift transaxle range selector lever in the PARK position when the ignition switch is in the LOCK position.
  • requires the floor shift transaxle range selector lever to be in the PARK position to turn the ignition switch to the LOCK position.

May 04, 2015 | 2000 Ford Taurus

1 Answer

I HAVE A 2007 DODGE CHARGER AND CAN NOT SHIFT OUT OF PARK. WHAT COULD BE THE PROBLEM?


Sounds like the gearshift interlock is not working. I assume you know you have to hold your foot on the brake with the ignition switched on. Check all the fuses. If they're ok you may need to take it to an auto electrician unless you can find the fault in the interlock system yourself. It may be that the switch may be faulty or out of adjustment. It is located down on the brake pedal.

Sep 20, 2014 | Dodge Charger Cars & Trucks

1 Answer

Now to install igintion switch


Removal & Installation The ignition switch or warning switch can be replaced without removing the steering lock assembly. The ignition switch is on the back of the assembly and the warning switch on the side.
  1. Disconnect the negative battery cable and insulate the terminal end.

CAUTION The air bag system must be disarmed before removing the steering wheel. Failure to do so may cause accidental deployment, property damage or personal injury.

  1. Remove the steering wheel and the steering column upper and lower covers.
  2. Remove the spiral cable assembly.


23482ab.gif
View of the steering lock and ignition switch assembly

  1. Remove the combination switch from the steering column.
  2. Remove steering column support nuts and lower the steering column.
  3. Disconnect the ignition switch wiring and interlock cable (if equipped).
  4. Remove the bolts that secure the steering lock and remove steering lock assembly.
To install:
  1. Install the steering lock assembly and secure with new shear type bolts.
  2. Connect the ignition switch wiring harness and the interlock cable.
  3. Raise the steering column and secure with mounting nuts.
  4. Install the spiral cable assembly.
  5. Install the combination switch, steering column covers, and the steering wheel.
  6. Connect the negative battery cable and enable the air bag system.

May 23, 2010 | 1997 Nissan Maxima

1 Answer

I need to change my ignition cylendar.


Ignition Lock Cylinder REMOVAL & INSTALLATION 1997–99 Models CAUTION
Some models covered by this manual are equipped with a Supplemental Restraint System (SRS), which uses an air bag. Whenever working near any of the SRS components, such as the impact sensors, the air bag module, steering column and instrument panel, disable the SRS, as described in Section 6. NOTE: Before continuing with this procedure, make sure to have available a new steering wheel retaining bolt and two lock cylinder retaining bolts. Once removed, these parts lose their torque holding ability (or retention capability) and must not be reused.
  1. If equipped, disarm the air bag system and disconnect the negative battery cable.
  2. If necessary, remove the steering wheel.
  3. Remove the combination switch.
  4. Unplug the ignition switch wiring connectors.
  5. Remove the ignition and shifter interlock cable mounting bracket bolt and position the assembly to one side.
  6. Cut a groove in the ignition cylinder bracket bolts with a chisel and hammer or use a similar method.
  7. Using a screwdriver, remove and discard the bracket bolts.
  8. Remove the ignition switch lock cylinder and bracket. To install:
  9. Install the new ignition switch and the bracket into position on the steering column tube.
  10. Install the new lock cylinder bolts and tighten the bolts enough to hold the switch in position.
  11. Check for proper switch operation by rotating the key to each position. If necessary, reposition the lock cylinder until it operates properly.
  12. If positioned properly, tighten the retaining bolts until the bolt head shears off.
  13. Position the interlock cable bracket. Install and tighten the retaining bolt to 35–53 inch lbs. (4–6 Nm).
  14. Attach the wiring connector to the ignition switch.
  15. Install the combination switch.
  16. If removed, install the steering wheel.
  17. Connect the negative battery cable.
  18. Confirm operational status of the air bag system by turning the ignition key to the RUN position and visually monitoring the air bag indicator lamp in the instrument cluster. The indicator lamp should illuminate for approximately 6 seconds and then turn OFF. If the indicator lamp does not illuminate, stays ON, or flashes at any time, a fault has been detected by the air bag diagnostic monitor.
  19. Check the steering wheel, horn and combination switch functions for proper operation.
Fig. 1: Unfasten the ignition and shifter interlock cable mounting bracket bolt, and position the assembly to one side

72a6db6.gif
Fig. 2: Use a chisel and hammer to cut a groove in the ignition cylinder bracket bolts — 1991–96 models shown; 1997–99 models similar

9849583.gif

Aug 30, 2009 | 1998 Ford Escort

1 Answer

Remove ignition tumbler


lock cylinder removal

Section 11-04: Steering Column 1996 Escort, Tracer Workshop Manual
REMOVAL AND INSTALLATION Ignition Switch Lock Cylinder Removal
  1. stf~us~en~file=ani_caut.gif~gen~ref.gif WARNING: THE ELECTRICAL CIRCUIT NECESSARY FOR DRIVER SIDE AIR BAG MODULE DEPLOYMENT IS POWERED DIRECTLY FROM THE BATTERY. TO AVOID ACCIDENTAL DEPLOYMENT AND POSSIBLE PERSONAL INJURY, THE BATTERY GROUND CABLE MUST BE DISCONNECTED PRIOR TO SERVICING OR REPLACING ANY DRIVER SIDE AIR BAG MODULE SYSTEM COMPONENTS.
    Remove the steering wheel (3600). Refer to the procedure in this section.
  1. Remove the multi-function switch (13K359). Refer to Section 11-05 for the removal procedure.
  1. Disconnect the ignition switch electrical connector.
  1. Remove the ignition/shifter interlock cable mounting bracket bolt and position the ignition/shifter interlock cable mounting bracket and the ignition/shifter interlock cable (3F719) aside.




  1. Remove the four steering column upper mounting bracket bolts and lower the steering column (3C529).
  1. Use a hammer and chisel to make a groove in the head of each of the two ignition switch lock cylinder bracket bolts.


    0764353.gif

  1. Remove the two ignition switch lock cylinder bracket bolts with a screwdriver and discard the bolts.




  1. Remove the ignition switch lock cylinder and the ignition switch lock cylinder bracket.
Installation
  1. Position the ignition switch lock cylinder and bracket and install two new bolts, tightening them only enough to hold the ignition switch lock cylinder in position.
  1. With the key in the ignition, verify the operation of the ignition switch lock cylinder. If necessary, reposition the ignition switch lock cylinder until it operates properly.
  1. Tighten the ignition switch lock cylinder bracket bolts until the bolt heads break off.
  1. Position the steering column and install the four steering column upper mounting bracket bolts. Tighten the steering column upper mounting bracket bolts to 9-14 Nm (80-124 lb-in).
  1. On vehicles equipped with tilt column, remove the upper mounting bracket retaining pin.
  1. Position the ignition/shifter interlock cable mounting bracket and install the bolt. Tighten the ignition/shifter interlock cable mounting bracket bolt to 4-6 Nm (35-53 lb-in).
  1. Connect the ignition switch electrical connector.
  1. Install the multi-function switch. Refer to Section 11-05 for the installation procedure.
  1. Install the steering wheel. Refer to the procedure in this section.
  1. Inspect the shift interlock system. Refer to Section 07-05 for the procedure.

Apr 07, 2009 | 1995 Mercury Tracer

Not finding what you are looking for?
2002 Hyundai Santa Fe Logo

Related Topics:

288 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8572 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...