Question about 1999 Chevrolet S-10 Pickup

Open Question

How do you install mlp sensor on 4l60e - 1999 Chevrolet S-10 Pickup

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

7.3l. Why does it keep shutting off in reverse?


The MLP sensor usually causes this concern. Manual Position Sensor. Located on transmission

Sep 01, 2015 | 1996 Ford F250 Crew Cab

1 Answer

I have a 1993 2500 that came out with a 4l60e


Change speed sensor plug in did you also change the ecm because you have are it won't shift

May 07, 2014 | 1993 Chevrolet K2500

1 Answer

Where is the neutral safety switch located on 1998 ford crown victoria


On 1992 and later models, the neutral safety switch is incorporated into the Manual Lever Position or Transmission Range MLP/TR sensor.

RENOVAL & INSTALLATION
  1. Disconnect the negative battery cable.
  2. Raise and support the vehicle safely on jackstands.
  3. Place the transmission in Neutral.
  4. Remove and discard the manual control lever nut, then remove the lever from the transmission.
  5. Detach the TR sensor electrical harness connector, remove the TR sensor retaining bolts, then pull the TR sensor off of the transmission case.
To install:
  1. Position the TR sensor against the transmission case and loosely install the 2 retaining screws.
  2. Attach the TR sensor electrical harness connector.
  3. Use an alignment tool, such as the TR Sensor Alignment Tool T93P-70010-A, to align the TR sensor slots.
  4. Tighten the TR sensor bolts to 80-100 inch lbs. (9-11 Nm).
  5. Position the manual control lever onto the TR sensor, then install the new lever nut to 22-26 ft. lbs. (30-35 Nm).
  6. Lower the vehicle.
  7. Connect the negative battery cable.
ADJUSTMENT
zjlimited_779.gif


Fig. : Adjusting the MLP sensor (click image for zoom)


Park is the last detent when the manual control lever is full forward. Return 2 detents toward the output shaft for Neutral.

  1. Position the manual control lever in Neutral .
  2. Raise the and safely support the vehicle.
  3. Loosen the sensor retaining bolts.
  4. Insert Gear Position Sensor Adjuster tool T93P-700 10-A or equivalent, into the slots.
  5. Align all 3 slots on the MLP sensor with 3 tabs on the tool.
  6. Tighten the attaching screws to 80-100 inch lbs. (9-11 Nm).
  7. Lower the vehicle.
Hope this helps (remember to rating ans leave a testimonial commnet about this free answer).

Oct 11, 2011 | 1998 Ford Crown Victoria

1 Answer

Where is the neutral safty swith on a 2006 ford focus


There isnt a neutral safety switch. There is a manual lever position sensor(MLP). It combines all the fuctions of backup lights, neutral safety, and informing the PCM what gear you have selected into one unit. Follow the shift cable out to the transmission, and at the end, Follow the shift cable out to the transmission, and at the end, you will find the MLP.
Pendin if its auto or manual

Mar 20, 2011 | 2000 Ford Focus

1 Answer

1992 Ford Bronco Transmission Problems (E4OD)


Here is what code E40D is:
TRANSMISSION - E40D - DIAGNOSTIC TROUBLE CODES - WATER INTRUSION OF THE MLP/TR SENSOR
TRANSMISSION - E40D - POSSIBLE WATER INTRUSION INTO THE MLP/TR SENSOR CAUSING SHIFT CONCERNS AND/OR HARSH ENGAGEMENT CONCERNS
TRANSMISSlON - E40D - SHIFT CONCERNS AND/OR HARSH ENGAGEMENT CONCERNS DUE TO WATER INTRUSION OF THE MLP/TR SENSOR
1989-94 BRONCO, ECONOLINE, F-150-350 SERIES, F-47, F-53, F-59
here is possible fix:
ISSUE: Some vehicles may exhibit a shift concern and/or a harsh engagement concern due to water intrusion into the MLP/TR sensor and vehicle harness. There may also be a number of different DTC's along with those concerns.
ACTION: Replace the MLP/TR sensor and vehicle harness connector if signs of water is evident.

Jan 18, 2010 | 1992 Ford Bronco

3 Answers

4l60e tranny swap


No the 4l60e is a electronic transmission you need to find a 700r4 transmission which are very common. Check with your local junk yards and are pretty easy to install. About a full days worth of work for a person with general know how of vehicles.

Sep 23, 2009 | 1994 GMC Sierra

2 Answers

Looking for the neutral safety switch


Neutral Safety/Back-up Light Switch

This is a combination switch which controls both Neutral Safety and Back-up lamp circuits.

C6 Transmission


8290dff.jpg

C6 neutral start switch
  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle on jackstands.
  3. Remove the downshift linkage rod return spring at the low-reverse servo cover.
  4. Coat the outer lever attaching nut with penetrating oil. Remove the nut and lever.
  5. Remove the 2 switch attaching bolts, disconnect the wiring at the connectors and remove the switch.
  6. Installation is the reverse of removal. Adjust the switch and tighten the bolts to 55-75 inch lbs. (6.2-8.5 Nm).
  7. Remove the jackstands and lower the vehicle.
  8. Connect the negative battery cable.
AOD Transmission

e7f4231.jpg

Removing the AOD neutral start switch
  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle on jackstands.
  3. Disconnect the wiring from the switch.
  4. Using a deep socket, unscrew the switch.
  5. Installation is the reverse of removal. Tighten the switch to 10 ft. lbs. (14 Nm).
  6. Remove the jackstands and lower the vehicle.
  7. Connect the negative battery cable.
4R70W Transmission

2f68dfc.jpg


Removing the Manual Lever Position (MLP) sensor

As of 1994, the neutral safety switch is referred to as a Manual Lever Position Sensor (MLP).
  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle on jackstands.
  3. Disengage the harness connector from the MLP sensor.
  4. Remove the 2 sensor attaching bolts and remove the sensor.
To install:
  1. Install the MLP sensor and install retaining bolts. Do not tighten, the sensor requires adjustment.
  2. Adjust the MLP sensor then tighten attaching screws to 80-100 inch lbs. (9-11 Nm).
  3. Remove the jackstands and lower the vehicle.
  4. Connect the negative battery cable.


ADJUSTMENT

C6 Transmission
  1. Hold the steering column transmission selector lever against the Neutral stop.
  2. Move the sliding block assembly on the neutral switch to the Neutral position and insert a 0.091 in. (2.3mm) gauge pin in the alignment hole on the terminal side of the switch.
  3. Move the switch assembly housing so that the sliding block contacts the actuating pin lever. Secure the switch to the outer tube of the steering column and remove the gauge pin.
  4. Check the operation of the switch. The engine should only start in Neutral and Park .

4R70W Transmission


4cc4151.jpg


Adjusting the MLP sensor

Park is the last detent when the manual control lever is full forward. Return 2 detents toward the output shaft for Neutral.
  1. Position the manual control lever in Neutral .
  2. Insert Gear Position Sensor Adjuster tool T93P-700 10-A or equivalent, into the slots.
  3. Align all 3 slots on the MLP sensor with 3 tabs on the tool.
  4. Tighten the attaching screws to 80-100 inch lbs. (9-11 Nm).

I hope help you. Good luck (rated this help).

Sep 17, 2009 | Ford E-250 Cars & Trucks

1 Answer

Where and what is a tr/mlp sensor for transmission?


It mounts on driver's side of transmission where linkage is.

Another concern is did water get into the trans.? If so then that could be a problem. The glue that is used to bond the clutches to the plates in the tranny is water soluable,in other words it will cause them to unbond. The only fix for that is replacement of the clutches.

Feb 04, 2009 | 2002 Ford Explorer

Not finding what you are looking for?
1999 Chevrolet S-10 Pickup Logo

Related Topics:

140 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8269 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...