Question about Mazda B2200

1 Answer

I have a 88 mazda b2200 it cranks up easy but if i do not push on gas pedal it will die...any suggestions?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

Sounds like a carb problem, like the choke isn't functioning. Try some carb cleaner, and spray into the carb, and also check the air filter.
It could also be a vacuum leak. Check to make sure that all hoses and wires are connected properly.

Posted on Feb 07, 2012

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
rcampsr
  • 90 Answers

SOURCE: how to put on ignition switch on a '88 mazda b2200

If you mean actually replacing the ignition switch on the vehicle with a locking column. You need to do this. Dicconnect the battery, remove the lower panel of the dash if there is any. There is a bolt on the steering column near the fire wall on most vehicles, remove this bolt, it will release the spline on the steering column. Disconnect all wiring going to the column, unbolt the column from the dash support. Remove the column from the truck, on the ignition switch you will see where the two shear bolts screw the assembly together, center punch the center of each bolt. Now drill the bolt with a 1/8" drill about 1/4" to 3/8" deep. Now use a 3/8" drill and drill out the shear head until it comes off the bolt. You can now remove the switch assembly from the column. The new assembly should come with new shear off bolts so when you bolt it in place when tightned they will break off rendering it tamperproof again. Most vehicles are designed like this now to stop theft. Check the column for operation before reinstalling it in the reverse of above. You just want to make sure the key locks and unlocks the column before reinstalling in the vehicle. You may want to do this before you totally tighten the bolts and break them off permanently. Good luck, RAC

Posted on Apr 14, 2009

  • 7 Answers

SOURCE: 88 volvo 240 starts most of the time but dies when i push gas

Wow. any number of things. Clogged fuel filter? Fuel pump relay. Try getting in the car when it's quiet around you. Turn the key to "on", not start. You should hear the fuel pumps hum for a few seconds and then stop. If you don't hear them, check your fuse box. They are labeled but I believe #6 is usually the main fuel pump fuse. If fuses are good, then it could be your fuel pump relay. These typically develop cracks in the solder and when they warm up, break contact and theengine dies. The relay is accessed by removing the 7 screws that hold your glovebox in. Slide it out as a unit. Remove the glove box bulb if you're going to be at it any great length of time or your battery will die. The relay is a white rectangular box clipped to a metal frame on the left of the now exposed innards. It has like 6-8 pins. Thump it a couple of times and see if the car will start. If it does, replacethe relay. Order online as much cheaper than dealership.
If you do hear the pumps cycle when you turn the key to on, then most likely you have a bad ignition module. Your '88 has LH2.2 so there is no crank sensor to go bad. The ignition module is mounted to the driver's side under hood by air cleaner. Small flat black rectangle w/ silver metal base.
If all this is Greek to you, try a Volvo specific forum like swedespeed.com

Posted on Apr 21, 2009

  • 8 Answers

SOURCE: 1992 B2200 Mazda timing instructions

this site has all the specs
http://www.mazdatruckin.com/B2200//B2200_Timing_Belt.html

Posted on May 10, 2009

  • 1 Answer

SOURCE: my 98 s10 will not stay running

my 98 chevorlet s10 v6 4.3 auto turns on but dies in a couple a seconds with kickin noise. is it the fuel injection or the fuel pump

Posted on Oct 28, 2009

  • 7353 Answers

SOURCE: need a heater core diagram for a 91 mazda b2200

The only thing to do is get a diagram from the MAZDA dealer parts dept. "A few parts fell out" is way to vague to help you.

Posted on Dec 30, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

'88 Mazda 323 cranks, but won't start.


I wouldn't flood one cylinder and expect it to start. Try using a small amount of starting fluid in the air filter to confirm your plug wires are installed and working correctly.

Mar 26, 2014 | 1988 Mazda B2200

1 Answer

B2200 jerks and hesitates


Check fuel pressure. If good, rebuild carb.

Nov 12, 2017 | 1988 Mazda B2200

2 Answers

1989 mazda b2200 can not set timing


i have a 1988 mazda b2200 and i was sittin still runnin and it was a lil low in water and i was just ab to take off when it cut off. it made steam *** out the hood. the thing is its gettin eletric to the plugs and its gettin gas and i even tried a lil eather and its turnin over it just want crank. do u have a idea wat it could b? im thinkin it jump timeing.

Feb 17, 2010 | 1988 Mazda B2200

1 Answer

How do you change the starter out of a 88 mazda pickup B2200???


first things first make sure you unhook you battery then mark all the wires to your starter as you are removing them. remove the starte.then put its all back the way it was.

Apr 29, 2009 | 1988 Mazda B2200

1 Answer

1990 mazda b2200 starts & idle but dies if I push on the gas.


You need to run a pressure check on the fuel line with the appropriate gauge.

Mar 07, 2009 | 1988 Mazda B2200

1 Answer

Gas problems


2 things...either the timing is off or more than likely the catalytic converter is plugged...How many miles are on it??

Jan 14, 2009 | 1988 Mazda B2200

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

418 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...