Question about 1990 Volkswagen Golf

Open Question

97LEXUSES300 TIMEINGMARKS FOR TIME BELT INSTALL

Posted by on

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
techbuster
  • 5081 Answers

SOURCE: 1.8 1990 golf gl

If the engine has a plastic upper timing belt cover,you need to remove the cover to set the camshaft timing marks located at the rear of the sprocket (ignore any marks on the front of the sprocket).

Whip off the plastic covers and check the timing marks before you strip anything down.
Some of the 8v's have a mark on the front of the camshaft sprocket (which lines up with a mark on the back plastic cover) and some of them have the mark on the back of the pulley (which lines up with the flat surface of the head / rocker cover)
If you line up the crank mark, and then mark the camshaft sprocket and the dizzy driveshaft you cant go far wrong.
Make sure you change the tensioner as well as the belt as these are known for failing.
A special tool is advised for the tensioner (sort of like a grinder spanner), but you can get away with using a pair of circlip pliers (2 holes in the tensioner to grip on)

4f20409.jpg

Posted on Sep 22, 2010

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I install fan and alternator belt?


question 3 , and double posted....
and still no hint as the the JOB.
what are you doing and why, so we are on same page?

wow,,, you do make this so hard.
if the questions is new belt time"only"?(yes? do i guess good?)
then i posted last post all 11 steps from the real fsm ON REMOVAL. so, now I add page 2.
So now you want ,INSTALL too?
the below only works if you did page 1 correctly

ok here. 11 more steps, totaling 22



Install the drive belt to the crankshaft pulley, the tensioner and the generator.

Rotate the drive belt tensioner clockwise.

Install the drive belt to the idler pulley (1).

NOTE

Important: Ensure the drive belt is properly aligned and seated into the grooves of the accessory drive pulleys.

Slowly release the drive belt tensioner.

Raise the vehicle.

Install the right side engine mount bracket. Refer to Engine Mount Bracket Replacement - Right Side .

Install the engine splash shield. Refer to Engine Splash Shield Replacement - Right Side .

Lower the vehicle.

Install the engine mount strut bracket. Refer to Engine Mount Strut Bracket Replacement - Right Side .

Remove the engine support fixture. Refer to Engine Support Fixture .

Install the the air cleaner assembly. Refer to Air Cleaner Assembly Replacement .

Jan 08, 2016 | 2005 Suzuki XL-7

1 Answer

1995 2.3L 4W ISUZU RODEO HOW DO YOU GET IT BACK IN TIME


Remove timing belt cover and the timing belt. Line up the cam gear timing mark with the mark that is behind it. Then, set the crankshaft pulley timing mark to zero degrees or whatever the book says. Then re-install the timing belt and re-torque the timing belt tensioner to the proper torque. Turn the engine one full turn, with a breaker bar and socket. Re-check the timing marks on the crankshaft and camshaft. Re-install the timing belt cover and everything else you took off to get to the belt. Be sure to torque the crankshaft pulley bolt to specs.

Sep 27, 2014 | 1995 Isuzu Rodeo

1 Answer

99 kia sporage timing marks


Hi there:



Check this information...

dfd3ea1.gif


Crankshaft match marks


Align marks on timing belt pulley and pump body.

Camshaft pulley alignment marks
9f1c7ef.gif



  1. Align marks on camshaft pulleys with alignment marks on seal plate.
  2. Install timing belt. NOTE: No looseness should exist on the tension side and at the camshaft pulleys.
  3. Loosen tensioner lock bolt.
  4. Turn crankshaft 2 revolutions in direction of rotation and check that timing marks are still in alignment.
  5. Tighten timing belt tension lock bolt to 27-38 ft lb (32-52 Nm).
  6. Apply a force of 22 lbs to timing belt between camshaft sprockets.
  7. Belt deflection should measure 0.30-0.33 in (7.5-8.5 mm)


  1. NOTE: Replace tensioner spring if timing belt deflection is excessive.
  2. Timing Belt Installation


eb770f2.gif

  1. Install lower timing belt cover.
  2. Install upper timing belt cover.
  3. Install power steering drive belt and adjust belt tension.
  4. Install fan pulley.
  5. Install generator drive belt and adjust belt tension.
  6. Install A/C drive belt and adjust belt tension.
  7. Install splash guard.
  8. Install fan and fan shroud.
  9. Install 4 fan bolts. Tighten to 24 ft lb (33 Nm).
  10. Install fan shroud mounting bolts.
  11. Install fresh air duct.
  12. Connect hose to resonance chamber.
  13. Connect battery negative cable.


Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.


Thank you for using FixYa, have a nice day.

Mar 14, 2012 | Kia Sportage Cars & Trucks

1 Answer

Problem with 99 kia


Hi there:Check this information...

dfd3ea1.gif


Crankshaft match marks


Align marks on timing belt pulley and pump body.

Camshaft pulley alignment marks
9f1c7ef.gif



  1. Align marks on camshaft pulleys with alignment marks on seal plate.
  2. Install timing belt. NOTE: No looseness should exist on the tension side and at the camshaft pulleys.
  3. Loosen tensioner lock bolt.
  4. Turn crankshaft 2 revolutions in direction of rotation and check that timing marks are still in alignment.
  5. Tighten timing belt tension lock bolt to 27-38 ft lb (32-52 Nm).
  6. Apply a force of 22 lbs to timing belt between camshaft sprockets.
  7. Belt deflection should measure 0.30-0.33 in (7.5-8.5 mm)


  1. NOTE: Replace tensioner spring if timing belt deflection is excessive.
  2. Timing Belt Installation


eb770f2.gif

  1. Install lower timing belt cover.
  2. Install upper timing belt cover.
  3. Install power steering drive belt and adjust belt tension.
  4. Install fan pulley.
  5. Install generator drive belt and adjust belt tension.
  6. Install A/C drive belt and adjust belt tension.
  7. Install splash guard.
  8. Install fan and fan shroud.
  9. Install 4 fan bolts. Tighten to 24 ft lb (33 Nm).
  10. Install fan shroud mounting bolts.
  11. Install fresh air duct.
  12. Connect hose to resonance chamber.
  13. Connect battery negative cable.


Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.


Thank you for using FixYa, have a nice day.

Mar 14, 2012 | Kia Sportage Cars & Trucks

1 Answer

Hiwich timing mark I used to time the balancer shaft on a 99 honda accord with a 2.3L


To Install:
NOTE: Clean balancer belt drive pulley, timing belt pulleys and upper/lower timing cover prior to belt installation.
honda-03-23-3425.gif

  1. Set timing belt drive pulley to TDC by aligning dimple on pulley with dimple on oil pump. honda-03-23-3426.gif

  2. Set camshaft pulley to TDC so that "UP" mark is at top and grooves align with top of cylinder head. Timing belt installation honda-03-23-3549.gif

  3. Starting with driver pulley, install timing belt in a counterclockwise sequence.
  4. Loosen and ten retighten adjusting nut.
  5. Install balancer belt drive pulley. NOTE: Inspect rubber seal on lower cover and replace as necessary.
  6. Install lower cover.
  7. Install crankshaft pulley and bolt.
  8. Rotate crankshaft pulley counterclockwise several times to seat belt.
  9. Loosen adjusting nut 1 turn.
  10. Rotate crankshaft counterclockwise 3 teeth on camshaft pulley.
  11. Tighten adjusting nut to 33 ft lb (44 Nm). honda-03-23-3542.gif

  12. Turn crankshaft pulley until TDC is achieved. honda-03-23-3426.gif

  13. Ensure that camshaft pulley "UP" mark is at top and grooves align with top of cylinder head.
  14. Remove crankshaft pulley and lower cover.
  15. Rotate crankshaft to TDC again and lock timing belt adjuster arm with a 6 mm timing cover bolt.
  16. Loosen adjuster nut 1 turn and ensure that belt tensioner freely moves.
  17. Push tensioner up and tighten adjusting nut. Balancer shaft alignment honda-03-23-3556.gif

  18. Remove bolt and washer from maintenance hole.
  19. Using a 6 X 100 mm bolt, scribe a mark 2.9 in (74 mm) from end.
  20. Insert bolt into maintenance hole and hole in balancer shaft.
  21. Install bolt up to scribed line. Balancer shaft alignment honda-03-23-3557.gif

  22. Align groove on balancer shaft with pointer on oil pump housing.
  23. Install balancer belt and loosen adjusting nut 1 turn to tension.
  24. Retighten bolt. Balancer shaft alignment honda-03-23-3556.gif

  25. Remove bolt from maintenance hole and install bolt and washer. Tighten to 22 ft lb (29 Nm).
  26. Reinstall crankshaft pulley.
  27. Loosen adjusting nut 1 turn.
  28. Rotate crankshaft pulley counterclockwise 1 turn and tighten adjusting nut.
  29. Remove bolt from timing belt adjuster arm. NOTE: Inspect rubber seal on lower cover and replace as necessary.
  30. Remove crankshaft pulley.
  31. Install lower cover.
  32. Install seal at adjusting nut. NOTE: Crankshaft pulley, bolt and washer must be cleaned prior to installation.
  33. Lubricate crankshaft pulley bolt between head and washer and bolt threads with clean engine oil. honda-03-23-3537.gif

    CAUTION
    Do not use impact wrench to perform following step.
  34. Install crankshaft pulley and tighten bolt using special tools to 181 ft lb (245 Nm).
  35. Install dipstick/tube assembly.
  36. Install upper cover. Tighten bolts to 9 ft lb (12 Nm).
  37. Install cylinder head cover.
  38. Install alternator bracket and alternator.
  39. Install power steering pump belt and alternator belt. Upper bracket installation honda-03-23-3420.gif

  40. Install upper bracket and tighten fasteners in proper numbered sequence.
  41. Install stop.
  42. Install battery and enter radio anti-theft code.
prev.gif next.gif

Jul 03, 2010 | Cars & Trucks

2 Answers

How do i put timing belt and water pump?


REMOVAL & INSTALLATION of timing belt: Fig. 1: View of the timing belt cover 91163p64.gif
Fig. 2: Loosen then timing belt tensioner using a ratchet and short socket 91163p65.gif
Fig. 3: Matchmark the direction of rotation of the timing belt 91163p67.gif
Fig. 4: Once loose, pull the belt off the camshaft pulley 91163p71.gif
  1. Disconnect the negative battery cable.
  2. Turn the crankshaft to align the timing belt matchmarks and set cylinder No. 1 to Top Dead Center (TDC) on the compression stroke. Once in this position, the engine must NOT be turned or disturbed.
  3. Remove all necessary components to gain access to the cylinder head and timing belt covers.
  4. Remove the cylinder head and timing belt covers.
  5. There are 2 belts in this system; the one running to the camshaft pulley is the timing belt. The other, shorter one drives the balance shafts and is referred to as the balancer belt or timing balancer belt. Lock the timing belt adjuster in position by installing one of the lower timing belt cover bolts to the adjuster arm.
  6. Loosen the timing belt and balancer shafts tensioner adjuster nut, but do not loosen the nut more than 1 turn. Push the tensioner for the balancer belt away from the belt to relieve the tension. Hold the tensioner and tighten the adjusting nut to hold the tensioner in place.
  7. Carefully remove the balancer belt. Do not crimp or bend the belt; protect it from contact with oil or coolant. Slide the belt off the pulleys.
  8. Remove the balancer belt drive sprocket from the crankshaft.
  9. Loosen the lockbolt installed to the timing belt adjuster and loosen the adjusting nut. Push the timing belt adjuster to remove the tension on the timing belt, then tighten the adjuster nut.
  10. Remove the timing belt. Do not crimp or bend the belt; protect it from contact with oil or coolant. Slide the belt off the pulleys.
  11. If defective, remove the belt tensioners by performing the following:
    1. Remove the springs from the balancer belt and the timing belt tensioners.
    2. Remove the adjusting nut.
    3. Remove the bolt from the balancer belt adjuster lever, then remove the lever and the tensioner pulley.
    4. Remove the lockbolt from the timing belt tensioner lever, then remove the tensioner pulley and lever from the engine.
  12. This is an excellent time to check or replace the water pump. Even if the timing belt is only being replaced as part of a good maintenance schedule, consider replacing the pump at the same time. To install:
  13. If the water pump is to be replaced, install a new O-ring and make certain it is properly seated. Install the water pump and retaining bolts. Tighten the mounting bolts to 106 inch lbs. (12 Nm).
  14. If the tensioners were removed, perform the following to install them:
    1. Install the timing belt tensioner lever and tensioner pulley. NOTE: The tensioner lever must be properly positioned on its pivot pin located on the oil pump. Be sure that the timing belt lever and tensioner moves freely and does not bind.
    2. Install the lockbolt to the timing belt tensioner, do not tighten the lockbolt at this time.
    3. Install the balancer belt pulley and adjuster lever.
    4. Install the adjusting nut and the bolt to the balancer belt adjuster lever. Do not tighten the adjuster nut or bolt at this time. NOTE: Be sure that the balancer lever and tensioner moves freely and does not bind.
    5. Install the springs to the tensioners.
    6. Move the timing belt tensioner its full deflection and tighten the lockbolt.
    7. Move the balancer its full deflection and tighten the adjusting nut.
  15. The crankshaft timing pointer must be perfectly aligned with the white mark on the flywheel or flex-plate; the camshaft pulley must be aligned so that the word UP is at the top of the pulley and the marks on the edge of the pulley are aligned with the surfaces of the head.
  16. Install the timing belt over the pulleys and tensioners.
  17. Loosen the bolt used to lock the timing belt tensioner. Loosen, then tighten the timing belt adjusting nut.
  18. Turn the crankshaft counterclockwise until the cam pulley has moved 3 teeth; this creates tension on the timing belt. Loosen, then tighten the adjusting nut and tighten it to 33 ft. lbs. (45 Nm). Tighten the bolt used to lock the timing belt tensioner.
  19. Realign the timing belt marks, then install the balancer belt drive sprocket on the crankshaft.
  20. Align the front balancer pulley; the face of the front timing balancer pulley has a mark, which must be aligned with the notch on the oil pump body. This pulley is the one at 10 o'clock to the crank pulley when viewed from the pulley end.
  21. Align the rear timing balancer pulley (2 o'clock from the crank pulley) using a 6 x 100mm bolt or rod. Mark the bolt or rod at a point 2.9 in. (74mm) from the end. Remove the bolt from the maintenance hole on the side of the block; insert the bolt or rod into the hole. Align the 2.9 in. (74mm) mark with the face of the hole. This pin will hold the shaft in place during installation.
  22. Install the balancer belt. Once the belts are in place, be sure that all the engine alignment marks are still correct. If not, remove the belts, realign the engine and reinstall the belts. Once the belts are properly installed, slowly loosen the adjusting nut, allowing the tensioner to move against the belt. Remove the pin from the maintenance hole and reinstall the bolt and washer.
  23. Turn the crankshaft 1 full turn, then tighten the adjuster nut to 33 ft. lbs. (45 Nm). Remove the bolt used to lock the timing belt tensioner.
  24. Install the lower cover, ensuring the rubber seals are in place. Install a new seal around the adjusting nut, DO NOT loosen the adjusting nut.
  25. Install the key on the crankshaft and install the crankshaft pulley. Apply oil to the bolt threads and tighten it to 181 ft. lbs. (250 Nm).
  26. Install the upper timing belt cover and all applicable components. When installing the side engine mount, tighten the bolt and nut attaching the mount to the engine to 40 ft. lbs. (55 Nm) and the through-bolt and nut to 47 ft. lbs. (65 Nm).
  27. Connect the negative battery cable.
---
For water pump removal and installation contact me:

Jul 12, 2010 | 1997 Honda Civic

1 Answer

How do i replace the alternator?


REMOVAL & INSTALLATION
  1. Disconnect the negative battery cable.
  2. If equipped with a pulley cover shield, remove the shield at this time.
  3. Loosen the alternator pivot bolt. Remove the adjustment arm to alternator bolt. Pivot the alternator to gain slack in the drive belt and remove the belt.
  4. Disconnect and label (for correct installation) the alternator wiring. NOTE: Some models use a push-on wiring connector on the field and stator connections. Pull or push straight when removing or installing, or damage to the connectors may occur.
  5. Remove the pivot bolt and the alternator. Fig. 1: Alternator harness connections 86753014.gif
    Fig. 2: Remove and set aside the alternator belt 86753300.jpg
    Fig. 3: Remove the alternator pivot bolt 86753301.jpg
    Fig. 4: Tag and disconnect the wiring harness connector 86753302.jpg
    Fig. 5: Remove the alternator when it is completely detached 86753303.jpg
    To install:
  6. Position the alternator assembly onto the vehicle. Install the alternator pivot and adjuster arm bolts, but do not tighten them at this time.
  7. Install the alternator drive belt and adjust the drive belt tension.
  8. Once the proper belt tension is reached, tighten the adjuster bolt to 24–40 ft. lbs. (33–54 Nm) and the pivot bolt to 40–50 ft. lbs. (54–67 Nm).
  9. Reconnect the alternator wiring.
  10. Install the pulley shield, if equipped.
  11. Connect the negative battery cable.
prev.gif next.gif

Jul 11, 2010 | 1989 Ford Taurus

2 Answers

How do you tighten the main belt that connects to altonater water pump power steering ect.


The job of maintaining belt tension falls on the Belt Tensioner. It's time to replace it. They're pretty reasonable in the $25-$35 range.


d2432d8.jpg

Feb 20, 2010 | 1995 Ford Explorer

1 Answer

I need a diagram on how to replace a 2001 chevy metro alternator.


2001 Chevrolet Metro 1.3L MFI SOHC 4cyl

Alternator - Removal & Installation
  1. Before servicing the vehicle, refer to the precautions section.
  2. Remove or disconnect the following:
    Negative battery cable Air cleaner assembly Alternator electrical connectors Accessory drive belt Upper and lower mounting bolts Alternator
To install:
  1. Install or connect the following:
    Alternator and the bolts, do not tighten the bolts at this time
  2. Install the alternator belt and adjust the tension until a deflection of 0.24-0.31 inch (6-8mm) deflection with 22 lbs. (10 kg) of pressure exerted when installing a used belt. On a new belt the belt deflection should be 0.20-0.27 inch (5-7mm) with 22 lbs. (10 kg) of pressure exerted.
    Alternator electrical connectors, then torque the alternator bolts to 17 ft. lbs. (23 Nm) Air cleaner assembly Negative battery cable
  1. Before servicing the vehicle, refer to the precautions section.
  2. Remove or disconnect the following:
    Negative battery cable Accessory drive belt Alternator electrical connectors Alternator
To install:
  1. Install the alternator and hand-tighten the bolts.
  2. Install the alternator belt and adjust the tension until a deflection of 0.24-0.31 inch (6-8mm) deflection with 22 lbs. (10 kg) of pressure exerted when installing a used belt. On a new belt the belt deflection should be 0.20-0.27 inch (5-7mm) with 22 lbs. (10 kg) of pressure exerted.
  3. Install or connect the following: Upper alternator bolt to 18 ft. lbs. (25 Nm) Lower alternator bolt to 40 ft. lbs. (54 Nm) Alternator electrical connectors Accessory drive belt Negative battery cable

    459fdba.jpg
    Fig. Exploded view of the alternator-Metro and Prizm models
Hope thats help (remember rated this).

Feb 18, 2010 | 2001 Chevrolet Metro

Not finding what you are looking for?
1990 Volkswagen Golf Logo

Related Topics:

90 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

yadayada
yadayada

Level 3 Expert

76846 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8567 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...