Question about 2004 Pontiac Grand Prix

Open Question

Pictures of water pumps on 2004 pontiac gtp supercharger

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 1779 Answers

SOURCE: serpertine belt diagram

0900c152800a326f.gif
Copyright © 2002 Delmar, All Rights Reserved.

Posted on Oct 19, 2008

Ad
  • 176 Answers

SOURCE: Where is the egr valve on a 1999 pontiac grand

upper left side of engine, near throttle body

.

  1. Disconnect the electrical connector from the EGR valve.
  2. Remove the EGR valve retaining nuts
  3. Remove the EGR valve
  4. Remove the gasket from the EGR valve adapter .
INSTALLATION PROCEDURE
  1. Install a new gasket on the EGR adapter . NOTE: Refer to Fastener Notice in Cautions and Notices.
  2. Install the EGR valve and the retaining nuts . Tighten Tighten the nuts to 30 N.m (22 lb ft) .
  3. Connect the EGR valve electrical connector.


Posted on Jun 30, 2009

jturcotte
  • 8266 Answers

SOURCE: i need a diagram on

from autozone.com

f5bfeae.jpg

Posted on Sep 01, 2010

jturcotte
  • 8266 Answers

SOURCE: 2004 pontiac grand prix, gtp , water pump

no, here is procedure according to autozone.com


3.8L Engine

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the engine coolant.
  3. Remove or disconnect the following:

    Negative battery cable. Drive belt Water pump pulley Power steering pump and move it aside Water pump

    0996b43f80208f64.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Exploded view of the water pump assembly mounting-3.8L engine


To install:
  1. Install or connect the following:

    Water pump using a new gasket and torque the long bolts to 25 ft. lbs. (34 Nm) and the short bolts to 16 ft. lbs. (22 Nm) Water pump pulley and torque the bolts to 115 inch lbs. (13 Nm) Power steering pump and torque the bolts to 25 ft. lbs. (34 Nm) Drive belt Negative battery cable
  2. Fill the cooling system.
  3. Start the vehicle and check for leaks, repair if necessary.

Posted on Sep 29, 2010

  • 15 Answers

SOURCE: 2004 Grand Prix GTP (supercharged.)

at normal operating temp your car should run around 200 degrees. the thermostat is what maintains the temp of the engine by opening and closing alowing water to circulate and cool the engine or closed allowing the temp to build up. if the thermostat is stuck open then the coolent is never in the engine long enough to heat up and removes the heat faster than the engine is producing it. A new thermostat is around ten dollars and is simple to replace. Allow the engine to cool all the way down. Get a catch can, take the radiatior cap off and on the bottom right of the radiatior there is a valve, open the valve and drain about a gallon of coolent out. Once you have done this follow your top radiator hose from the radiator to the thermostate housing. There are two bolts one on each side 14 mm remove these bolts and the housing comes up. Remove the thermostate and put the new one in making sure the cone part is up, replace the housing and tighten the bolts. Top off the radiatior with coolent and start the engine leave the cap off and allow the engive to come up to operating temp. once it is warmed up you should be able to rev the engine alittle and see the coolent in the radiator being pulled thru by the water pump. top off the radiator and put the cap back on you are ready to go. after you have drove the car for a few days or ten miles or so let the engine cool down and check the coolent level to make sure its full. air bubbles can get trapped in the system.

Posted on Dec 18, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 1998 Pontiac grand prix GTP supercharged 3.8 coupe will die and cannot restart for 5-30 minutes. When engine is hot or not. Vacuum problem?


VACUUM PROBLEMS USUALLY CAUSE IDLE PROBLEMS NOT A COMPLETE SHUTDOWN. SOUNDS MORE LIKE A FUEL PUMP RELAY.

May 05, 2015 | Pontiac Cars & Trucks

1 Answer

HOW DO I REPLACE FREEZE PLUGS ON 04 3.8?


R&R motor. Knock out old freeze plugs and replace. 20+ job. Good luck.

May 21, 2014 | 2004 Pontiac Grand Prix GTP

1 Answer

Transmission Compatibility


As you see I provided you the models you can apply the transmission :The 4T65E-HD (code MN7) is a heavy duty version of the 4T65-E used with more powerful engines such as the LS4 V8 and L67/L32 supercharged V6. Applications: 2.93:1 MN7 Pontiac Bonneville SSEi L67 Chevrolet Impala L67 Chevrolet Monte Carlo L67 Pontiac Grand Prix GTP/GXP Buick Regal GS Buick Riviera L67 (97-99) So ,yes you can!

May 28, 2013 | 1998 Pontiac Grand Prix

2 Answers

How can I replace the water pump on a 2004 Grand Prix GTP superchargered?


WELL YOU NEED TO DRAIN COOLANT SYSTEM.PLACE A LARGE DRAIN PAN UNDER THE RADIATOR TO CATCH COOLANT WHILE DRAINING RADIATOR.ONCE ALL COOLANT DRAINED OUT.REMOVE DRIVE BELT.REMOVE WATER PUMP PULLEY.REMOVE POWER STEERING PUMP AND MOVE IT ASIDE.THEN REMOVE WATER PUMP.MAKE WATER PUMP MOUNTING SURFACE CLEAN THEN INSTALL NEW WATER PUMP AND GASKET IN PLACE.IF WATER PUMP GASKET IS PAPER TYPE PUT GASKET SEALANT ON BOTH SIDES OF THE GASKET.IF YOU HAVE RUBBER GASKET DONT USE NO GASKET SEALANT.INSTALL NEW WATER PUMP TORQUE LONG BOLTS TO 25 FT LBS AND TORQUE SHORT BOLTS TO 16 FT LBS.TORQUE WATER PUMP PULLEY TO 115 INCH POUNDS.TORQUE POWER STEERING PUMP BOLTS TO 25 FT LBS.THEN INSTALL DRIVE BELT.FILL THE COOLANT SYSTEM.START THE VECHICLE AND CHECK FOR LEAKS.

Mar 25, 2011 | Pontiac Grand Prix Cars & Trucks

1 Answer

Would replacing a power steering pump in a 2002 Grand Prix GTP Supercharger cause the SuperCharger belt to break.


No.

The supercharger belt is on the main drive, the water pump is on the accessory drive. Provided that they are both properly installed of course.

Jan 14, 2011 | 2002 Pontiac Grand Prix

1 Answer

My 2004 gran prix (gtp) just hit 100000 miles. What maintenance needs to be done now?


Spark plugs, transmission fluid and coolant change, supercharger oil, air filter, fuel filter, tires, brakes, engine mounts, BTSI inspection and power steering fluid. Also inspect the belts, hoses, pulleys and look for wiring damage.

Jul 02, 2010 | 2004 Pontiac Grand Prix

1 Answer

Remove supercharger on pontiac GTP 1999


Technically you are supposed to (change the s/c gasket) but if your careful and don't tear it, you don't really need to.

Be sure to inspect the yellow coolant o-rings.

The gasket thickness isn't going to matter at all on the supercharger gasket.

Perfect oportunity to install that Intercooler you always wanted ;)

Nov 10, 2008 | 2007 Cadillac CTS 3.6L

Not finding what you are looking for?
2004 Pontiac Grand Prix Logo

Related Topics:

217 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8265 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...