Question about Dodge Dakota

Open Question

How to adjust slave cylinder 87 dodge dakota

The throwout bearing runs constantly.

Posted by on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1252 Answers

SOURCE: can i see a diagram

michael_cass_94.jpgmichael_cass_95.jpgHope this helps you ??

Posted on Jun 19, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Does hydraulic slave cylinder bearing need greasing?


Hi Sheila:
The clutch slave cylinder pushes against a throwout arm
The throwout arm is a lever and it pushes against the throwout bearing which thenpresses against the clutch plate and dis-engages the clutch.
Throwout bearings are typically sealed units that last until they fail, at which time they get replaced.
You should not have to worry about greasing it.
Hope this helps.
Cheers.

Jan 27, 2016 | 1996 Ford F150 Regular Cab

1 Answer

Throw out bearing runs all the time


Most likely Weak or broken spring on the trust bearing plate.How to check. When the clutch is fully released push the plate towards the slave cylinder the piston in the slave cylinder should go in. I have sometimes fitted an external spring from the plate to the bolt on the slave cylinder to save removing the gearbox which does work but to do it properly you will need to remove the gearbox and fit a proper spring. Cheers

Feb 07, 2012 | Dodge Cars & Trucks

1 Answer

1989 Dodge Dakota 3.9L, How do you test the computer?


is there a spring between slave & throwout arm to pull slave back after engagement? Problem

Sep 25, 2010 | 1989 Dodge Dakota 2WD

1 Answer

Cant put my 98 Hombre in gear.


There are 4 parts to this system. First is the clutch master cylinder, second is the slave cylinder, third is the clutch throwout bearing, and last is the clutch pressure plate. These are all the parts that can be the issue. The master cylinder is the part that pumps the fluid to the slave cylinder, which pushes on the linkage to the throwout bearing, which pushes on the fingers on the clutch pressure plate, releasing the clutch. If you drained the fluid out, first you need to make sure that all the AIR is out of the system. It's just like brakes, it will not pump if it has air in it. The hydraulic portion of the system rarely gives problems, so here's a question. How old is the clutch in your truck? If it's over 100,000 mi, then you should start suspecting the throwout bearing. Did the truck make any groaning noises when you pressed the clutch recently, and then perhaps it stopped on its own? These are signs of throwout bearings going out. Here's the bit of troubleshooting that you need. go under your truck, and find where the slave cylinder attaches and pushes on the linkage that goes into the bell housing on the transmission. Feel this linkage; it should have very limited to no movement. if it moves significantly, then your throwout bearing went out, and you will need to replace your clutch and throwout bearing. If not, then it's the hydraulic portion of the brakes, and you'll have to troubleshoot between air in the system, master cylinder failure, or slave cylinder failure.

Feb 15, 2010 | 1998 Isuzu Hombre

1 Answer

Clutch pedal goes to floor and stays 1999 Nissan sentra 1.6 changed clutch presssure plate and throwout bearing surfaced flywheel has cable clutch have tried adjusting all ways


ON A 2000 MAX 6 CYLINDER HAS CLUTCH MASTER CYLINDER AND SLAVE CYLINDER, CHECK FLUID LEVEL AND BLEED CLUTCH SYSTEM AT SLAVE CYLINDER BLEEDER. HAVE NOT HEAR OF CABLE CLUTCH SYSTEM. ONLY HYDO.& LINKAGE. GOOD LUCK

Nov 05, 2009 | 2000 Nissan Maxima

1 Answer

Wher i s slave cylinder loc ated on 1998 doge


inside the bellhousing it is a slave and clutch bearing release collar all in one...

Oct 24, 2009 | 1998 Dodge Dakota

2 Answers

86 ford mustang 5.0 ho motor. just installed a clutch. wont go into gear. the cable has been adjusted. is there a slave cylinder adjustment too? or is the slave cylinder not workin properly


My '86 5.0 was a cable controlled clutch no slave or master cylinders. Make sure the throwout lever is seated properly, and check for movement when the clutch pedal is depressed. It should move at least .75 inches when depressed. Also make sure the bell housing is mating up to the engine completely and all bolts are tight. If all these things are ok it could be an improperly installed or wrong throwout bearing. I hope this helps. I remember what a pain that job was when I did mine esp. that screwy cable pulley thing attached to the clutch pedal. Which also may be the problem. Good luck.

Aug 12, 2009 | 1986 Ford Mustang

1 Answer

1998 Dodge dakota 4 cyl. manual trans.


You may want to try adjusting the clutch. I think Dodge have adjustment options. it seems that the throw out bearing is too close to the clutch and does not "throw out' as it should.

Oct 24, 2008 | 1998 Dodge Dakota

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

109 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7688 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...