Question about Seat Cordoba

Open Question

Hi please help! diagram cylinder head bolts torque seat 1.2 12V, 2005

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 98 Answers

SOURCE: how to rebuilt the cylinder head of daihatsu charade 3 cylinder engine

Which motor?

Posted on Sep 04, 2008

Ad
  • 1 Answer

SOURCE: Engine Bolt Torques- 2005 Chevy Impala/3400 Engine

Head Bolts
Step one 37 ft lbs then tignten 120 degrees more

Rocker arms
Step one 11 ft lbs then tighten 90 degresss more

Upper intake
89 inch lbs
Lower intake
132 inch lbs

Posted on Dec 02, 2008

  • 88 Answers

SOURCE: Hi I'm looking for cylinder head torque settings for a 1992 BMW 316/318 e36

BMW cylinder torque setting all models

According to my service manual as follows.

Cyl head to engine block (torx e12 M10 bolts)

Stage 1 30nm (22 ft – lb)
Stage 2 + 90 degrees
Stage 3 + 90 degrees

Cyl head to lower timing chain cover 10nm (89in – lb)

The tightening sequence is from inside to outside crossover as normal. Loosening sequence is from outside to inside crossover. Remember to set torque wrench at low setting and work gradually up through the whole sequence until you get the desired torque.

Posted on Aug 29, 2009

inspectmycar
  • 233 Answers

SOURCE: 94 mazda B3000 3.0L cylinder head torque specs

Step 1 torque to 59 ft pounds
2. Loosen one full turn
3. 37 ft pounds
4. 68 ft pounds

Use torque sequence below
aca9f77.gif

Posted on Sep 17, 2009

  • 181 Answers

SOURCE: Correct torque on cylinder head bolts for Hyundai Elantra 1.8GLS

You have two bolt sizes the shorter or smaller of the two sizes is called M10 the torque is 22ft lbs +65 degrees +65 degrees again The larger of the two bolts is called a M12 the torque for these are 26ft lbs +65+65. There is a tightening order staring at the top center bolt and working in a circle They have to be torqued in three steps. If you dont under stand something about this repost and I can help you farther. If this is helpful please mark that it was I do this for free to help people DRIVE SAFE TIM

Posted on Feb 19, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Diagram 360 Dodge head bolt torque sequence


Hi Charles,here'a link showing you the head bolt torque sequence. Repair Guides Engine Mechanical Cylinder Head AutoZone com Yours is a 3.9 engine.

Aug 23, 2016 | Dodge Cars & Trucks

1 Answer

On a 3.8L what is the aspec diagram and tourque for the racker arm


Hi Juan, I'm AL the owner of Big As Auto Repair

Below is the torque specs for the rocker arm as you requested.

SPECIFICATIONS - TORQUE

DESCRIPTION N·m Ft. Lbs. In. Lbs. Camshaft Sprocket-Bolt 54 40 - Camshaft Thrust Plate-Bolts 12 - 105 Forged Connecting Rod Cap-Nuts 54 +¼ turn 40 +¼ turn - Cracked Connecting Rod Cap-Bolts (Refer to 9 - ENGINE/ENGINE BLOCK/PISTON & CONNECTING ROD - INSTALLATION) Crankshaft Main Bearing Cap-Bolts 41 +¼ turn 30 +¼ turn - Crankshaft Main Bearing Cap Cross Bolts (3.8L) 61 45 - Crankshaft Oil Seal Retainer Rear-Bolts 12 - 105 Crankshaft Damper-Bolt 54 40 - Cylinder Block Drain Plugs 20 15 - Cylinder Head-Bolts (Refer to 9 - ENGINE/CYLINDER HEAD - INSTALLATION) Cylinder Head Cover-Bolts 12 - 105 Flex Plate to Crankshaft 88 65 - Engine Mounting (Refer to 9 - ENGINE/ENGINE MOUNTING) Powertrain Torque Strut 54 40 - Exhaust Manifold-Bolts 23 - 200 Exhaust Crossover Pipe-Bolts 54 40 - Intake Manifold - Lower-Bolts 23 - 200 Intake Manifold - Lower Gasket Retainer-Bolts 12 - 105 Intake Manifold Upper-Bolts 12 - 105 Lifter Yoke Retainer-Bolts 12 - 105 Oil Filter Attaching Fitting 54 40 - Oil Cooler Attaching Fitting 27 20 - Oil Filter 20 15 - Oil Filter Adapter-Bolts 28 - 250 Oil Gallery Plug 27 20 - Oil Pan-Bolts 12 - 105 Oil Pan Drain-Plug 27 20 - Oil Pressure Switch 23 - 200 Oil Pump Cover Plate-Screws 12 - 105 Oil Pump Pick-up Tube-Bolt 28 - 250 Oil Dipstick Housing-Bolts 48 35 - Rocker Arm Shaft-Bolts 23 - 200 Spark Plug 16 12 - Thermostat Housing 12 - 105 Timing Chain Case Cover -M8 Bolt 27 20 - -M10 Bolt 54 40 - Water Pump-Bolts 12 - 105 Water Pump Pulley-Bolts 28 - 250
Should you need extra help visit my website here: http://www.bigasautorepair.com/

Apr 15, 2015 | 2005 Chrysler Pacifica

2 Answers

2002 nissan maxima 3.5 cylinder head torque


Hi there:

2_17_2012_6_58_18_pm.jpg

Fig. Cylinder head bolt loosening sequence - Altima & Maxima 3.5L engine

Install the cylinder head bolts and torque in sequence as follows:
  1. Step 1: 72 ft. lbs. (98 Nm).
  2. Step 2: Completely loosen all bolts.
  3. Step 3: 26-32 ft. lbs. (34-44 Nm).
  4. Step 4: plus 90-95 degrees clockwise.
  5. Step 5: plus 90-95 degrees clockwise.

2_17_2012_6_59_54_pm.jpg

Fig. Right cylinder head bolt torque sequence- Altima & Maxima 3.5L engine


2_17_2012_7_00_21_pm.jpg

Fig. Left cylinder head bolt torque sequence- Altima & Maxima 3.5L engine

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day

Feb 17, 2012 | Nissan Cars & Trucks

1 Answer

Whats is te cylinder heads torque for suzuki aerio 2.3 lts


Hi! Please don't forget to rate! Thanks!



c17hydro_181.gif

Cylinder head bolt torque sequence-2.0L and 2.3L engines



Apply engine oil to the bolt threads and tighten the cylinder head bolts, in sequence, using the following 6 Steps:

  • Step 1: 38.5 ft. lbs. (53 Nm)
  • Step 2: 61 ft. lbs. (84 Nm)
  • Step 3: Loosen all of the cylinder head bolts
  • Step 4: 38.5 ft. lbs. (53 Nm)
  • Step 5: 76 ft. lbs. (105 Nm)
  • Step 6: Bolt M6 (bottom left of cylinder head) - 8 ft. lbs. (11 Nm)

May 12, 2011 | 2003 Suzuki Aerio

1 Answer

Hi i'm eduardo and i have a '94 nissan pathfinder 4wd...engine 3.0.... i want to know the head torque specifications .


Hi Eduardo:
Check this information (click over pics for zoom)...

zjlimited_1062.jpg

Fig. 20: Exploded view of the cylinder head assembly-VG30E engine


zjlimited_1063.jpg

Fig. 15: Cylinder head loosening sequence-VG30i and VG30E engines


zjlimited_1064.jpg

Fig. 17: Cylinder head torque sequence-VG30i and VG30E engines


Install the cylinder head with a new gasket. Apply clean engine oil to the bolt threads and seats, then install the bolts with washers (beveled edges up) in the correct position. Note that bolts 4, 5, 12 and 13 measure 5.00 in. (127mm), and are longer than the others. The other bolts are 4.17 in. (106mm) long.

Tighten the bolts in the proper sequence, in the following stages:
Tighten all bolts, in order, to 22 ft. lbs. (29 Nm).
Tighten all bolts, in order, to 43 ft. lbs. (59 Nm).
Loosen all bolts completely.
Tighten all bolts, in order, to 22 ft. lbs. (29 Nm).
Tighten all bolts, in order, to 40-47 ft. lbs. (54-64 Nm). Or, if you have an angle torque wrench available, tighten them an additional 60-65 degrees.


Hope this helps; remember to rate this answer. Good luck.

Apr 22, 2011 | Nissan Pathfinder Cars & Trucks

2 Answers

Need the torque settings for a '94 cutlass supreme sl 3.1 in reference to the cylinder heads I need the sequence and the torque if possible a diagram


Heres the diagram and specs for the cylinder head and also i have enclosed the torque specs for the intake and its tightening sequence, good luck and hope this is helpful, have a good day.
Cylinder head bolts. Step 1) tighten to 44 ftlbs.
Step 2) tighten an additional 95 degrees.

Lower intake bolts. Step 1) all bolts are tightened to 115 inch lbs.


Upper intake bolts.Step 1) all bolts tighten to 18 ft,lbs no diagram, start in the middle and work your way out going cris cross.johnjohn2_88.gifjohnjohn2_89.gif

Mar 19, 2011 | Oldsmobile Cutlass Supreme Cars & Trucks

1 Answer

Correct pressure for torque the head of mazda pickup 1998


Since you didn't say which engine you have, I've pulled torque specs for 3 different engines. Also, since I can't include a diagram showing the relative locations of the numbered head-bolt locations, it would be a good idea for you to purchase a vehicle specific repair guide that will show this info.


Take particular note about the TTY (Torque to Yield) bolts used on 2 of the 3 engines shown. It is said that new head bolts MUST BE USED when head is replaced or re-installed to obtain the proper torque.



B2500 4 Cylinder

Torque sequence: --------- ' 10 6 2 4 8 ' front ' ' ' 7 3 1 5 9 ' -----------Step 1: torque in sequence to 51 Ft/Lbs Step 2: torque again in sequence to 51 Ft/Lbs Step 3: final tighten all bolts an additional 90 to 100 degrees recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) that permanently stretch during the initial installation. New head bolts must be used when cylinder head is replaced or re-installed to obtain proper torque.







B3000 3.0 6 Cylinder

Torque sequence ---------- ' 6 4 2 8 ' ' ' ' 5 1 3 7 ' ---------- Step 1: torque to 59 Ft/Lbs Step 2: loosen in sequence (1) full turn Step 3: torque to 41 Ft/Lbs Step 4: torque to 73 Ft/Lbs









B4000 4.0 6 Cylinder

Torque sequence --------- ' 5 1 3 7 ' ' ' ' 6 4 2 8 ' --------- Step 1: torque cylinder head bolts in sequence to 26 Ft/Lbs Step 2: torque cylinder head bolts to 56 Ft/Lbs Step 3: turn cylinder head bolts in sequence an additional 90-degrees recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) that permanently stretch during the initial installation. New head bolts must be used when cylinder head is replaced or re-installed to obtain proper torque.


Good luck with this job!

Feb 06, 2011 | 1998 Mazda Pickup

1 Answer

Need torque settings for cylinder head bolts on a 52 reg skoda fabia 1.4 16v any help much appreciated thanks


Torque settings for cylinder head bolts for Skoda Fabia 1.4 16v

Cylinder head bolts tightening order:

tdisline_116.jpg

IMPORTANT NOTE: RENEW BOLTS!

Stage 1: Tightening torque = 30 Nm
Stage 1: Tightening torque = 90 Degrees
Stage 1: Tightening torque = 90 Degrees

Please do rate my response. Thanks!

Dec 17, 2010 | Volkswagen Polo Cars & Trucks

1 Answer

Looking for head bolt troque spec for 3.4l impala sfi04


Please don't forget to rate. Thank you:

Left side front cylinder head


98e175a.gif
Cylinder head bolt torque sequence-3.4L engine

  • Cylinder head by aligning it with the dowel pins
  • New cylinder head bolts coated with a sealant (such as GM 1052080). Torque the bolts in the proper sequence (1-8) to 37 ft. lbs. (50 Nm). Using a torque angle meter turn the bolts 90 degrees in the proper sequence.
  • Left side exhaust manifold. Torque the bolts to 12 ft. lbs. (16 Nm).
  • Spark plugs. Torque the plugs 11 ft. lbs. (15 Nm).


  • Right side rear cylinder head:


    71cd5b7.gif
    Cylinder head bolt torque sequence-3.4L engine


  • New cylinder head gasket
  • Cylinder head on top of the gasket and make certain it is lined up properly with the dowel pins
  • New cylinder head bolts coated with a sealant (such as GM 1052080). Torque the bolts in the proper sequence (1-8) to 37 ft. lbs. (50 Nm). Using a torque angle meter turn the bolts 90 degrees in the proper sequence.
  • Right side exhaust manifold. Torque the bolts to 12 ft. lbs. (16 Nm).
  • Spark plugs. Torque the plugs 11 ft. lbs. (15 Nm).
  • Spark plug wires
  • Exhaust crossover pipe. Torque the fastener to 18 ft. lbs. (25 Nm).
  • Valve rocker arms and pushrods. Torque the fastener to 89 inch lbs. (10 Nm). Using a torque angle meter torque the fastener an additional 30 degrees.
  • Lower intake manifold. Torque the bolts to 115 inch lbs. (13 Nm).
  • Upper intake manifold. Torque the bolts to 18 ft. lbs. (25 Nm).
  • Nov 26, 2010 | 2004 Chevrolet Impala

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    30 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Seat Experts

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22306 Answers

    yadayada
    yadayada

    Level 3 Expert

    77499 Answers

    Adam Truesdale

    Level 3 Expert

    485 Answers

    Are you a Seat Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...