Question about Cars & Trucks

Open Question

I need a tool to hold a 1995 toyota camry/4cyl/2.2 engine harmonic balacer to take off the bolt. where would be the best place to look for one?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
DickCanFixIt
  • 948 Answers

SOURCE: How to read trouble codes on 1998 Toyota Camry w/o scan tool

You can go to any auto parts store and they will usually read them for you for free. Around the late 90s many of the auto computer systems began requiring scan tools rather than the older method of simply flashing lights on the dash if you jumpered the correct pins.

Posted on Dec 31, 2008

Ad
localwonder
  • 6784 Answers

SOURCE: reverse suddenly quit 95 toyota camry 4cyl auto

Check your transmission fluid level asap. if the level is good, you will need to inspect the shift solenoids located inside the transmission pan. replace any solenoids that are proven to be faulty. i would also advise to test the pcm/tcm for its operational value as well. this device controls the shifting patterns of the auto trans.

while checking the solenoids, if you notice any metal fragments on the bottom of the pan, this will be a sign of major gear friction. you should re build in this case.

Posted on May 24, 2009

co7196
  • 3433 Answers

SOURCE: cannot remove harmonic balancer bolt on 96 honda (2.2L)

You may need an impact gun. If loctite was used, you will need a gun.

Posted on Sep 13, 2009

  • 9 Answers

SOURCE: Trying to change the timing belt on a 2003 Hyundai

you can put a breaker bar and socket on the bolt and unplug a) the injectors or b) the coils so it wont start and crank it over like 2 times put the breaker bar on the pulley with the handle of the breaker bar touching the ground and u crank it and it'll break free

Posted on Oct 19, 2009

MauiRentaCar
  • 288 Answers

SOURCE: 95 4cly camry sometimes shuts off when gas peadl

Bad ignition coil. Replace.

Posted on Feb 23, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have a 95 toyota camry. I was asked from auto parts employee how many bolts did the bell housing have. I have no clue. Can someone help please


Bell housing is the area where your transmission bolts to the engine. There any bolts all around it. You need to count them all and give them the exact amount.

Nov 20, 2016 | 1995 Toyota Camry

2 Answers

Where is crank position sensor on a 1994 toyota 2.2liter 4cyl ?


Where is the crank position sensor on a 95 Toyota celica gt 2.2

search.aibing.cc/Where+is+the+crank+position+sensor+on+a+95+Toyota...
P1335, No Crankshaft Position Sensor Signal - Engine Running. ... 91 1991 ToyotaCelica GTS Engine Mount Right 2.2L 4 Cyl Genuine. ... 1990, 1991, 1992, 1993, 1994, 1995, 1996, 1997, 1998, 1999, 2000, 2001 . ... Powered by a 2.2-liter engine, the Celica now had ST and GT trim models. ... in 1986 and a 2.0-liter ...

Where is crank position sensor on a 1994 toyota 2.2liter 4cyl ...

www.fixya.com/cars/t26080657-crank_position_sensor_1994_toyota
31 mins ago - It is not behind pully nor in dist all videos show - Toyota Cars & Trucks question. ... Change a crankshaft position sensor on a 2000 eclipse.

toyota camry crankshaft sensor - ABMforum.com

abmforum.com/toyota-camry-crankshaft-sensor.html
toyota camry crankshaft sensor 99 camry crankshaftcamshaft position codes i got a problem with my 97 ... The car 96 toyota camry 2.2 liter 4 cyl. ... 1994 toyota camry 2.2L 257k miles Symptoms Car overheats Top radiator hose hot bottom cold ...

Toyota Camry 5SFE Engine Timing Belt, Water Pump and ...

hubpages.com > Autos > Do It Yourself Auto Repair
Jul 10, 2014 - The Toyota 5SFE motor is a four-cylinder, 2.2 liter, timing-belt-driven, double ..... Remove the lower timing belt cover with the crankshaft position sensor. ..... I've never, ever replaced the harmonic balancer on a 4cyl 5SFE.

1995 Toyota Camry LE 4 cylinder - YouTube

? 2:27
https://www.youtube.com/watch?v=7TW6hlUiHWQ
Sep 6, 2011 - Uploaded by jacasan2000

Feb 03, 2016 | Toyota Cars & Trucks

1 Answer

What will cause the engine light and the OD lights to flash when engine is running? this is on a 95 toyota camry 4cyl.


Transmission problem or electrical issues

You will need a shop that still has older
OBD1 System scan tools & knowledge

(OBD1 1983 thru 1995) Newer systems are obd2

Oct 03, 2012 | Toyota Cars & Trucks

1 Answer

I need the location of the harmonic balancer on my 2.2l Ecotec engine. Car is 2004 Chevrolet Cavalier LS.


CRANKSHAFT PULLEY IS THE HARMONIC BALANCER.YOU NEED THESE TOOLS TO REMOVE HARMONIC BALANCER, YOU NEED HARMONIC BALANCER REMOVER AND INSTALLER TOOL.YOU NEED A LARGE PIN SPANNER WRENCH TO HOLD HARMONIC BALANCER IN PLACE WHILE LOOSEN THE HARMONIC BALANCER BOLT.

May 21, 2011 | Chevrolet Cavalier Cars & Trucks

1 Answer

Can a 1996 4cyl camry thermostat and radiator fit a 1994 4cyl camry?


Mate.If the bolt holes line up and it all bolts together,it will work for you.Engine will be fine IF it bolts in.I think it does

Apr 20, 2011 | 1994 Toyota Camry

1 Answer

How to fix a front leaky oil seal in a 1995 Toyota Camry LE


Three seals to check. easiest is the valve cover seal. Number and remove the 4 wires going into your spark plugs. remove 4 nuts holding the cover and replace seal.
Next easiest is the distributor O-ring. Remove air filter assembly remove the distributor cap, then the distributor. With the valve cover still off, loosen the 2 bolts that clamp the distributor down. Remove the 2 terminal leads going into the distributor (4 wire terminal/2 wire terminal) Mark the case of the distributor and the case of the head with one line so you can line it back up on reinstallation. remove the 3 bolts holding the distributor down. Replace O-ring. replace distributor, align, tighten the 2 bolts, then tighten the 3 bolts. replace terminal wiring and cap. replace air filter assembly. Replace valve cover with new gasket. Place spark plug wires back into their proper places. The last one is the oil pan gasket. Drain all oil and remove all blots holding the pan. drop the pan and replace the gasket. Put it all back into place. Do not over tighten the pan bolts as this will cause the gasket to deform, making it leak again.

Nov 22, 2010 | 1995 Toyota Camry

2 Answers

2000 toyota camry 2.2L harmonic balancer how-to removal and replacement?


Take the tire off where the side of the armonic balancer is,if you have a air compact gun it1s more ease,remember to take the serpentine belt off to,if you dond have an impact gun,find a long enohg to lock in plece in some place of the car,then carefully,crank the engine not to starter it,just enogh to loose the tight bolt of the balancer.

Oct 26, 2010 | 2000 Toyota Camry

1 Answer

1994 toyota camry harmonic balancer bolt will not come loose v6


Hi:
Those bolts can be extremely tight, and the hardest part is holding the engine from turning. You often need a impact gun, or breaker bar, and I have had good success holding the engine with a chain type wrench, and protected the outside of the damper pulley with a piece of old belt.

Jan 29, 2010 | Toyota Camry Cars & Trucks

1 Answer

Exchange ignition switch in toyota camry


Remove the lower portion of the dash, and the steering column shroud. Using a DREMEL tool, and a ut-off disc, cut s line in the bolts that holds the ignition switch in, deep enough to insert a flat-blade screwdrive; then simply remove the 2 bolts.

Jul 17, 2009 | 1995 Toyota Camry

1 Answer

How to remove the Harmonic Balancer on a 1995 Toyota Camry sedan?


4. REMOVE ENGINE BALANCER
(a) Uniformly loosen and remove the 6 bolts in several
passes, in the sequence shown.
(b) Remove the engine balancer and spacers
5. CHECK CONNECTING ROD THRUST CLEARANCE
Using a dial indicator, measure the thrust clearance
while moving the connecting rod back and forth.
Standard thrust clearance:
0.160 − 0.312 mm (0.0063 − 0.0123 in.)
Maximum thrust clearance:
0.35 mm (0.0138 in.)
If the thrust clearance is greater than maximum, re−
place the connecting rod assembly. If necessary, re−
place the crankshaft.
6. REMOVE CONNECTING ROD CAPS AND CHECK
OIL CLEARANCE
(a) Check the matchmarks on the connecting rod and cap
to ensure correct reassembly.

(b) Remove the 2 connecting rod cap nuts.

(c) Using a plastic−faced hammer, lightly tap the con
necting rod bolts and lift off the connecting rod cap.
HINT: Keep the lower bearing inserted with the con
necting rod cap.
.

Mar 07, 2009 | 1995 Toyota Camry

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...