Question about Hyundai Tiburon

1 Answer

Needed new front wheel bearing.Garage heated to remove and cracked fairly new wheel disc.After they fitted new disc the car failed their brake test ,so they removed everything and found problem with something to do with either the caliper or piston,which they say probably caused problem in the first place.I have been told by friend that I should not pay for new discs and labour to fit them as wheel bearings should have been put in press to remove,not heated and whacked with a hammer (which probably also caused the damage to the piston)would be interested in your opinion. thank you in advance. Linda

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

First of all, they should have removed the caliper and rotor before they even touched that hub assembly. Also, as far as I know, a caliper can't cause wheel bearing failure. You should get the proper reimbursement for what they did. Sounds like they weren't good mechanics. I can easily see them damaging that rotor if they struck it with a hammer, especially if they heated everything up. Not so much the caliper, but if it braked fine before you pulled it in their garage, they broke that too. Good luck Linda.



Posted on Oct 22, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Front wheel bearings


first check the pads have not worn down to metal if they have the disc will have to be replaced , if the disc is in good condition and the pistons are free press them back into the cylinders and then the pads can removed .check the master cylinder does not over flow as the pistons are pushed back. Brake fluid is a paint remover. the wheel bearings don't have to be touched to replace pads. After new pads are fitted the brakes will have pumped to bring the pads out to the disc.

Aug 15, 2014 | Cars & Trucks

Tip

Mazda 323/Protege front wheel bearing


The moment you can hear a loud noise coming from front wheels while driving straight that means that your wheel bearings are ready for replacement. In a Mazda 323 BJ (1999-2004) it usually comes every 150-200 thousand kilometers (95-120k miles). To replace the bearing (do two of them in one go even if only one can be heard) you need to do as follows:
Loosen the nut on the half shaft, jack up the car, remove the wheel, dismantle brake caliper and brake disc, remove all ball joints attached to the hub, detach the shock absorber from the hub (no need of removing it completely), once you have the hub basically hanging on the half shaft, untie the nut and pull the hub out of the shaft so you can hold it in your hands. You will need to go to a garage with a 12ton (minimum) press, no point of trying to hammer the bearing out as you may damage the hub and your whole work will be for nothing. Get the old bearing pressed out and the new one pressed in.The Mazda part numbers for the front bearing kit are: B455-33-047A(B,D),GJ21-33-042B,G304-33-065,B21M-33-048.
After getting the bearing fitted into the hub, all we need is to reverse the whole process, put the shaft into the hub, attached the hub to the shock absorber (makes it easier to attach the rest), put the nut and tight it just as much to feel there is nearly no movement (do not overtight it as this might damage the bearing), attach all ball joints back to the hub. Make sure all nuts are tight, use a
tension wrench when needed, put the brake disc back on the hub, install the brake caliper, once you have all them on and tight put on the wheel, then get someone to press the brake while you tight the shaft nut with the tension wrench, check the wheel for play or hard movement. Lower the car down and take a slow drive around (do not accelerate sharply or brake rapidly, just a gentle drive around. Normally a wheel bearing should be in correct position and use after about 200km (120 miles) distance. After that check if it is not overheating (too tight) or there is a play (too loose). Tight or untight if necessary, recheck after same 200km (120 miles).

on Apr 24, 2010 | Mazda 323 Cars & Trucks

1 Answer

Applied brakes pulsate. front pads and rotors are good. rear brake pads are fair and rotors


If ABS is activating for no apparent reason then the most common causes are failed ABS wheel sensors or more commonly, cracked reluctor rings.

You won't usually see the crack in a reluctor ring, but it opens up when it rotates at running speeds. You can also get it to show with a simple fluorescent dye crack testing kit (not cheap to buy for a one-off job, but any decent garage or engineering workshop will have a kit to hand).

Unfortunately, reluctor rings are expensive as they usually come as an integral part of the driveshaft or hub assembly. Third party versions may be available and are less expensive (still a painful price though) but to fit them they must be heated until cherry red and then dropped into position. Get it wrong and you have to cut off your new and expensive ring and start again. Not really a DIY job unless you're very confident and experienced.

If the crack test proves negative, then ABS sensors are easy to fit and can be tested by swapping around to see if you can move the fault from one wheel to another or even from the front to the rear. Sensors are relatively cheap, but failures are far less common than with reluctor rings.

Fingers crossed for you that it's the easy/cheap fix.

May 27, 2010 | 2002 Audi A6

1 Answer

I am getting a pulsing feeling from the front wheels when braking on my 2004 Chrysler Sebring. It feels like one or more of the rotors are warped. How do I replace the front rotors with new ones. Thanks.


If they are not worn beyond tollerance they can be machined on the vehicle.
Also make sure its not tyres or wheel bearings.

remove wheel
remove brake caliper( leave the hose connected)
remove centre cap
remove split pin and lock
unscrew bearing hub nut
rotor should come off
fit new bearing races in new rotor
grease new bearings
fit inside bearing and seal
refit rotor, outer bearing,washer,nut,lock, splitpin and centre cap
(tighten nut until no play in bearing plus 1\8 of a turn)
refit caliper and wheel
bleed and test brakes before driving

Apr 28, 2010 | 2004 Chrysler Sebring

1 Answer

Suzuki Grand Vitara 1999:


Going by your description I think it could be something different, I would have the brake master cylinder checked, if you are suffering brake failure and shuddering it sounds like your callipers arent getting equal pressure when you apply the brakes. Or a freat lack of pressure to suffer brake failure. I hope this helps.

Nov 02, 2009 | 1999 Suzuki Vitara

2 Answers

Can you discribe the proceedure to replace the front wheel bearing on a 94 volvo 850 Thanks Rob


front wheel bearing comes as complete hub assembly remove brake calliper and brake disc remove drive shaft nut at the back of hub housing there are some bolts wire brush this area well use penetrating oil remove the bolts tap hub out of housing can be tight so take your time clean housing well then fit new hub secure bolts fit and tourqe up hub drive shaft nut fit disc and calliper

Oct 22, 2009 | 1994 Volvo 850

1 Answer

I have a bad wheel bearing how do I replace it


Hub and Bearing Assembly
ani_caut.gif CAUTION: Do not begin this removal procedure unless the following parts are available:
  • A new front axle wheel hub retainer (3B477) (Step 1).
  • A new inboard halfshaft joint stub shaft circlip.
Once removed, these parts must not be reused during assembly. Their torque holding ability or retention capability is diminished during removal.

Removal
  1. Turn ignition switch to the OFF position and place the steering column in the unlock position.
  1. ani_caut.gif CAUTION: Discard the front axle wheel hub retainer. It is a torque prevailing design and cannot be reused. If loosened, the retainer must be removed and a new one installed.
    Remove and discard front axle wheel hub retainer (3B477).
  1. Raise vehicle on hoist.
  1. NOTE: Make sure steering column is in the unlocked position, and do not use a hammer to separate tie rod end (3A130) from the front wheel knuckle (3K185) . Use extreme care not to damage boot seal.

    Remove cotter pin from tie rod end stud and remove slotted nut. Discard cotter pin and nut.
  1. Using Tie Rod End Remover 211-001 (TOOL-3290-D) or equivalent and Tie Rod End Remover Adapter 211-087 (T81P-3504-W), remove tie rod end from front wheel knuckle.
  1. ani_caut.gif CAUTION: Use extreme care not to damage boot seal. Do not use power tools to remove the nut, or bearing and seal damage will result. Loosen the nut first, then remove nut from stud using the hex hold feature.
    For SHO vehicles, remove vinyl cover from upper link stud.
    Remove stabilizer bar link (5K484) from front shock absorber (18124) .
  1. Remove disc brake caliper (2B120) and support with wire to obtain working space. Do not allow disc brake caliper to separate from the front disc brake caliper anchor plate (2B292) to prevent contamination of the disc brake guide pin journals. Do not allow disc brake caliper to hang from front brake hose (2078) . Remove front disc brake rotor (1125) . Remove front disc brake rotor from wheel hub (1104) by pulling it off the lug bolt (1107). If front disc brake rotor is difficult to remove from front wheel knuckle , strike front disc brake rotor sharply between lug bolt with a rubber or plastic hammer.
    If front disc brake rotor will not pull off, apply Rust Penetrant and Inhibitor D7AZ-19A501-AA or equivalent meeting Ford specification ESR-M99C56-A to inboard and outboard rotor/hub mating surfaces. Install 3-Jaw Puller 205-D027 (D80L-1013-A) or equivalent and remove front disc brake rotor by pulling on front disc brake rotor outside diameter and pushing on hub center. If excessive force is required for removal, check front disc brake rotor for lateral runout prior to installation. Refer to Section 06-00.
  1. Remove anti-lock brake sensor mounting bolt and front brake anti-lock sensor (2C204) .
  1. Remove and discard lower ball joint nut. Using Remover Adapter 211-211 (T96P-3010-A1), separate lower ball joint from front suspension lower arm (3078) .
  1. Using Rotunda Spring Compressor 014-00781 or equivalent, compress front coil spring (5310) until lower ball joint clears front suspension lower arm .
  1. Using Front Hub Remover/Replacer 204-069 (T81P-1104-C), Two Stud Adapter 205-237 (T86P-1104-A1), Metric Hub Remover Adapter 204-085 (T83P-1104-BH) and Front Hub Installer 204-067 (T81P-1104-A), press front wheel driveshaft joint (3B414) from wheel hub . Wire front wheel driveshaft joint to body to maintain a level position.


    df1570a.gif


    Item Part Number Description 1 204-085 (T83P-1104-BH) Metric Hub Remover Adapter 2 204-067 (T81P-1104-A) Front Hub Replacer 3 — Turn Wrench Counterclockwise 4 — Hold Wrench Stationary While Turning Other Wrench 5 204-069 (T81P-1104-C) Front Hub Remover/Replacer 6 204-067 (T81P-1104-A)1 Two Stud Adapter A — Make Sure Metric Hub Remover Adapter 204-085 (T83P-1104-BH) is Fully Threaded onto 1107 and is Positioned Opposite the Two Stud Adapter 205-237 (T86P-1104-A1)
  1. Remove and discard three hub and bearing retainer bolts from front wheel knuckle .
  1. NOTE: Wheel hub is not pressed into front wheel knuckle . Do not use slide hammer to remove a stuck wheel hub . Do not strike back of inner bearing race. Use of these methods will damage bearing internal parts.

    NOTE: If bearing carrier is corroded to front wheel knuckle , apply Rust Penetrant and Inhibitor D7AZ-19A501-AA or equivalent meeting Ford specification ESR-M99C56-A to the inboard and outboard wheel hub/knuckle mating surface and allow to soak.

    Remove wheel hub from front wheel knuckle .


    f8656a.gif

Installation
  1. NOTE: If wheel hub is damaged or if any end play is detectable, replace wheel hub . End play is not adjustable. If wheel hub is disassembled, the assembly must be replaced.

    Remove all foreign material from knuckle bearing bore for correct seating of new wheel hub.
  1. Lightly lubricate mating surfaces of bearing corner and front wheel knuckle.
  1. ani_caut.gif CAUTION: Knuckle bore must be clean enough to allow wheel hub to be completely seated by hand. Do not press or draw wheel hub into place.
    Position wheel hub in front wheel knuckle . Install three new hub and bearing retaining bolts. Tighten to 83-107 Nm (61-78 lb-ft).
  1. Push front wheel driveshaft joint into wheel hub . Hand start front wheel hub retainer.
  1. Slowly release Rotunda Spring Compressor 014-00781 or equivalent while guiding lower ball joint into front suspension lower arm .
  1. Install new lower ball joint nut. Tighten to 68-92 Nm (50-67 lb-ft).
  1. Install tie rod end into front wheel knuckle . Install new slotted nut and tighten to 47-63 Nm (35-46 lb-ft). If necessary advance nut to install a new cotter pin.
  1. ani_caut.gif CAUTION: Use extreme care not to damage boot seal. Do not use power tools to tighten nut or bearing and seal damage will result. Install nut using hex hold feature to prevent the stud from rotating.
    Install stabilizer bar link to front shock absorber . Install stabilizer bar link nut. Tighten to 77-103 Nm (57-75 lb-ft). For SHO vehicles, install stud cover.
  1. NOTE: Remove rust from the rotor and hub mating surfaces with a medium abrasive pad.

    Install front disc brake rotor and disc brake caliper . Tighten caliper anchor bracket bolts to 88-118 Nm (65-87 lb-ft).
  1. ani_caut.gif CAUTION: The front axle wheel hub retainer must be tightened to specification immediately during installation. If the retainer is not tightened immediately, the nylon lock will set incorrectly, leading to incorrect torque readings and bearing failure. Any front wheel hub retainer that is not immediately tightened to specification or is loosened must be removed and a new retainer installed.
    Install front axle wheel hub retainer . Tighten to 230-275 Nm (170-203 lb-ft).
  1. Install wheel and tire. Tighten lug nuts (1012) to 115-142 Nm (85-104 lb-ft).
  1. Lower vehicle.
  1. Pump brake pedal prior to moving vehicle to position brake linings.

May 28, 2009 | 1999 Ford Taurus

1 Answer

Fit brake discs and pads to ford falcon longreach ute


after removing the wheel, remove the 2 bolts on the brake caliper. place a clamp on the flexy brake line to stop fluid loss. remove the caliper then remove the pads. undo the bleed nipple and push the piston back into the caliper. do up the nipple. undo the front wheel bearings and remove the disk. pack the wheel bearings and fit the front hubs. fit the brake pads then the caliper. remove the clamp check the fluid levels and pump the brakes brakes should be done by a professional because if the fail you can only die once
happy motoring

Apr 04, 2009 | 1983 Ford Fairmont

2 Answers

R and R front wheel bearing


no its a hub and bearing you have lift the truck remove wheels front remove caliper braket that hold the brake pads behind 4 bolt that hold the bearing cv joint nut in the middlehammer the bearing to loosen it up sometime there hard to remove after its off clean where the bearing goes so it will fit good if you have abs disconnect the connector reassemble good luck pierre p.s yes you can do that in our garage the only thing is you need some tolls

Jan 31, 2009 | 2001 Pontiac Aztek

1 Answer

Hyundai coupe se 2ltr 2001 front wheel bearing ceased to brake disk


hiya this does sound iffy ? but b4 i comment /offer an opinion could you or your friend jack up the wheel in question that has had repair and look at how the brake disc is secured to the actual hub assy that wheel bearing is housed in ? also caliper? cracked?? is it now a new one? have never had problem renewing front or rear bearings in past using the correct tool/s a hydraulic press is the best method for removing excessive siezed components as for your friend now saying noise is from rear ? it may be pads worne or disc/s corrosion/scoured so investigate and update what you discover ? sounds like big hammer garage?

Oct 24, 2008 | 2001 Hyundai Tiburon

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

137 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

70347 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6876 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...