Question about 1990 Chevrolet Lumina APV

1 Answer

Car dosen't go in drive,however if i put it 2nd or 3rd gear it go's.

It seem like it work only if i use the shifter from low to drive to get going.but when i stop at a light i have to go back to low gear ,2nd then drive.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 12 Answers

Lazy tranny. scap vehicle if its a dodge

Posted on Jan 17, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a manual 1996 hyundai sonata where we put in a brand new clutch kit and all gears go into gear without any worries. but 1st, 3rd and 5th gears all function and drive as if it were in 3rd gear a


C heck that the cable for the gears has been securely tightened on the box as the cable case may be moving and not allowing selection of the gears

Mar 06, 2013 | Cars & Trucks

1 Answer

I suspect my 1995 windstar may have a bad modulator valve the fluid level seems to go away with no apparent leak and now it takes off in 2nd gear and won't shift to 3rd or od and the od light on t


I've been doing research on these vans. Seems I remember that if the OD light flashes >>> fluid level is low. Also, I read where Ford wants you to overfill fluid so as to allow you to go around corners without loss of lubracation. By this time you may have melted it down and bought a Honda. I have a 95 Teal color and just in flawless shape, however it won;t go in reverse. Just follow the hood ornament and don;t look back...right ! ?

Feb 28, 2013 | 1995 Ford Windstar

1 Answer

Speedometer quit and transmission will not work in 3rd or drive but will in 1st and 2nd


i have a 2003 chev s-10 pickup with automatic/ 4 cyl I am not able to move shifter from park to drive i believe my shifter cable is binding
gears selection matches fine when shifting. But will not get out park go to reverse or neutral selection only drive, 3rd, 2nd and 1st
do i need to replace shifting linkage cable?

Oct 01, 2012 | 1996 Chevrolet C1500

1 Answer

I have a 1998 z24 cavaler, while i was driving i put the car into 2nd to downshift because i was turning, as i put it into 3rd the shifter felt like it was broke and it does not want to go into 1st 2nd...


Hi...your problem is usually caused by the ****** shift linkage being stuck in two gears at the same time which can sometimes happen from shifting out of sequence. In order to fix this you need to get under the vehicle and manually shift one of the trannys linkage levers into a different position to free it so you will be able to shift normally once again. NOTE: Be extremely careful when working under the vehicle and take every precaution to ensure your safety first and foremost!

over4dy

Sep 14, 2011 | Chevrolet Cavalier Cars & Trucks

1 Answer

Had no problems with transmission ,came to a stop put in reverse would not go put back in drive and will only go in low gear


I take it the shifter will work at all selections made. The problem pertains to the automatic shifting inside the hydralic pump only which a transmission is. if its stuck in low gear the solenoid for 2nd & 3rd gear is bad. That will leave you in 1st gear only all the time until the bad solenoid is replaced

Jan 24, 2010 | 1994 Buick LeSabre

1 Answer

Can't get car in or out of gear


Throwout bearing will need to be replaced most likely. Otherwise cluctch plate or fork may have stuck

Aug 06, 2009 | Hyundai Motor 2002 Elantra

1 Answer

'94 Protege's auto trans: no overdrive, poor automatic upshifting


Suggestion try to check if the release bearing of the transmission is still ok and check also the transmission oil level and if you need to change the transmission oil.

Jun 09, 2009 | 1994 Mazda Protege

2 Answers

Transmisson,


Check you linkage, go under your car and shifter by hand( with tool) at the trans. to first gear.and drive in first gear.

Jan 04, 2009 | 1997 GMC Jimmy

Not finding what you are looking for?
1990 Chevrolet Lumina APV Logo

Related Topics:

53 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

60541 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21927 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...