Question about 2002 Mitsubishi Montero Sport

1 Answer

Harmonic balncer my harmonic balncer came undone one day it unbolted itself the main bolt came undone and there seems to be a hole were a pin was going through the harmonic balancer into the crankshaft i believe the pin im assuming broke somone told me i had to replace the cam shaft key and another told me that i didnt have to i need your help in determining the problem

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 243 Answers

Hi there,
it seems that your explanation is a little bit confusing. Could you tell me what engine( 4D56??) and describe a little bit more in details about the pin you are worried about?
Cheers

Posted on Oct 27, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have a 2006 chevy trailblazer i change all the mounts inclunding the idol tentionor and its still vibrates and make niose when am in drive or reverse in park and neutal its fine but just when am in


If the harmonic balancer wobbles when the engine is running, it could cause a vibration. A typical balancer has a rubber seal between the balancer and the belt drive pulley. The rubber seal may have deteriorated.

Dec 27, 2014 | 2006 Chevrolet Trailblazer

1 Answer

Volvo s80 t6 after putting my serpintine belt back on when i started the car a good size of the belt ripped of and wrapped around my harmonic balncer to the timming belt and shut my car right down


Did the piece of serpentine belt actually make contact with the timing belt ? The timing belt should have been behind the timing cover.
And does the engine crank normally ? Normal compression ?

Jan 24, 2014 | 1999 Volvo S80

1 Answer

Removing a harmonic balancer


Most balancers will wiggle off (pull & wiggle) you will need the big centre bolt undone & if 4 small bolts around balancer undo those to cause they are probably bolted to the crank gear.

Jul 05, 2012 | 2005 Ford Explorer

1 Answer

How do i remove harmonic balancer & replace


YOU NEED A HARMONIC BALANCER PULLER TOOL AND A 15M SIX POINT SOCKET TO REMOVE HARMONIC BALANCER BOLT.TURN OFF RADIO AND REMOVE THE DRIVE BELT AND REMOVE THE NEGATIVE BATTERY CABLE. REMOVE THE STARTER SO YOU CAN PUT A LARGE SCREW DRIVER OR LARGE PUNCH TO STICK IN ONE OF THE FLY WHEEL HOLES TO KEEP ENGINE FROM TURNING WHEN YOU LOOSEN THE HARMONIC BALANCE BOLT. ALSO SCREW DRIVER AND PUNCH CAN KEEP ENGINE FROM TURNING WHEN REMOVER THE HARMONIC BALANCER. YOU WILL NEED A HELPER TO HOLD PUNCH OR SCREW DRIVER WHILE YOU LOOSEN THE BOLT. YOU CAN GO TO SEARS OR ANY AUTO PARTS STORE AND BUY HARMONIC BALANCER PULLER.TORQUE HARMONIC BALANCER BOLT TO 76 FT LBS.

Apr 23, 2011 | 2003 Pontiac Montana

3 Answers

How do you remove the harmonic balancer on a 1987 GMC R3500 with a 454?


You remove the giant bolt, then you use a harmonic balancer puller, which essentially bolts up rather than using claws to grab. The bolts of the puller go into the pulley fastening bolt holes.

Something must happen to protect the crank threads, a spacer, using the retainer bolt, or whatever, just do not kill the threads.

Feb 25, 2011 | 1987 GMC R3500

2 Answers

I have a knock in the front of the moter in the pullys or harmonic balncer should you have free play in the balncer


No there should be no free play in the balancer. There is a rubber ring in the middle of two steel sections on that balancer that will rot out and cause a knockign issue and free play as you describe.

Jan 21, 2011 | 1994 Oldsmobile Ninety Eight Regency

1 Answer

Harmonic balncer


Remove belt, remove bolt from balancer with air impact wrench. Pull off no puller needed

Sep 11, 2010 | 1990 Buick LeSabre

1 Answer

Repairing of a 94 mazda,location of a Harmonic BalNCER


The lowest pulley that a belt goes around is the harmonic balancer.

Apr 27, 2010 | 1994 Mazda 626

1 Answer

I am trying to replace the clutch disc in a 1994


please explain what you mean by trans axle?? Now in queens english we call it a drive shaft ??because the gearbox and diff unit are all in one ,so you want to remove the drive shafts first ?? well firstly before you jack vehicle up undo the big nuts in the middle of the wheel ,then jack it up so bottom of gearbox is about 1mt high ,Then drain gearbox oil and remove the front wheels ,unbolt front suspension by lower track control balljoint ,unbolt the front calipers and then with the big nut out of the way push the drive shaft back and pull the suspension so the drive shaft comes away ,Now you should only have to remove the big nut in the other side one ,and use a block and tackle on supporting the gearbox so it stays hanging in the air and when you have undone the ancillarys so to speak you can just pull gearbox back a bit on the front side and work through the gap .Now what i do here is a bit of a cowboy trick but it works well ,and thats to drill a hole through the bell housing where the clutch bolts are so you fit the new clutch finger tight on the bolts making sure that the clutch is more or less central then push the gearbox in and make sure it closes up without pulling it in with the bellhousing bolts .Then using a 3/8 drive socket set tighten the clutch bolts through the hole one at a time turning engine with a big screwdriver on ring gear through starter motor hole ,go round twice though to make sure they are tight because of the locating stud?? ,TWICE bolt it all up and job done ,shouldnt take more than 3 hrs on my own ,but a weekend mechanic??? maybe a day ,Not a difficult job just dirty and greasy

Nov 10, 2009 | 1996 Dodge Ram 2500 Club Cab

Not finding what you are looking for?
Cars & Trucks Logo

204 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

64034 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...