Question about 1994 Ford Tempo

1 Answer

Camshaft positioning sensor

I tried to replace the camshaft positioning sensor on my 1994 ford tempo. The metal part that bolts on to the block tore away from the plastic. The sensor is still in the engine block but is not sticking out far enough to get a hold of it. I taped off the plug and strapped it down. It is a 4 cylinder 5 speed manual transmission. Any ideas would be appreciated.
Thanks
Jeff

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Ford Master
  • 63,291 Answers

Drill a hole and get an easyout from the hardware or auto parts store, there are manu sizes of easyout avail, decide which one you need and then get the correct drill bit to use with it.

Posted on Oct 21, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the vacuum modelator on a 1994 ford tempo


its mounted to the side of the transmission at the front, the vacuum hose is mounted to the centre of the valve and held in place by a single bolt and flat metal bracket.

Sep 14, 2014 | 1994 Ford Tempo

1 Answer

Hi can you tell me how much torque spectification to replace head gasket bolts, camshaft caps bolts, and camshaft pully bolts for 1994 GS 300 lexus Thank you very much for your help



  1. 60293.gif

    Cylinder head bolt tightening sequence - 1993-97

  2. Remove the head from the engine. If prying is necessary, use a protected blade; take great care not to damage the mating surfaces of the head and block.

  3. Clean the head and block of all gasket material. Take great care not to gouge or scratch the mating surfaces.

To install:

  1. Place a new gasket on the cylinder block. Make sure it is positioned correctly. Install the cylinder head in position.

  2. Lightly coat the head bolt threads and plate washers with engine oil. Install the bolts in the head.

  3. Uniformly tighten the head bolts in several passes in sequence, to 25 ft. lbs. (34 Nm).

  4. Mark the front of each bolt with a dot of paint. Following the correct order, tighten each bolt an additional 90 degrees. When complete, all the paint marks should face to the side of the engine.

  5. Again following the correct order, tighten the bolts another 90 degrees of rotation. When complete, the paint marks should face the rear of the engine, exactly 180 degrees away from the original starting point. Correct bolt torque is expressed as 25 ft. lbs. (34 Nm) + 90° + 90°.


Jan 07, 2011 | 1994 Lexus GS 300

2 Answers

1998 Ford Ranger 4.0 engine Engine will not start Code is Camshaft position sensor. Where is this located


It is behind the intake manifold in the center of the block, on the rear of the engine.

Jan 01, 2011 | Ford Ranger Cars & Trucks

2 Answers

How to replace the camshaft sensor in a 1998 pontiac grand am gt


YOU MUST REMOVE POWER STEERING PUMP, AND BELT THE SENSOR IS UNDER THE PUMP IN THE BLOCK.

Dec 19, 2010 | 1998 Pontiac Grand Am

1 Answer

Change cam position sensor chy


  1. Disconnect the negative battery cable.
  2. Detach the electrical harness connector from the camshaft position sensor.
  3. Unfasten the camshaft position sensor mounting bolt. There is a hole in the bracket for tool access to the sensor mounting bolt.
  4. Rotate the sensor away from the engine block.
  5. Pull the camshaft position sensor up out of the chain case cover. Do not pull on the sensor wire.
There is an O-ring on the sensor case. The O-ring may make removal of the sensor difficult. A light tap on top of the sensor prior to removal may reduce the force needed for removal. Inspect the O-ring for damage and replace if necessary.
To install:
If the sensor removed is going to be re-installed, clean off the old spacer on the sensor face. A new spacer must be attached to the sensor face before installation. If the sensor is being replaced, be sure that a paper spacer is attached to the sensor face and an O-ring is positioned in the groove of the new sensor.
  1. Apply 1-2 drops of clean engine oil to the O-ring prior to installing the sensor.
  2. Install the sensor into the chain case cover and rotate into position.
  3. Push down on the sensor until contact is made with the camshaft gear. While holding the sensor in this position, install and tighten the mounting bolt to 10 ft. lbs. (14 Nm).
  4. Attach the electrical harness connector to the camshaft position sensor.
  5. Connect the negative battery cable.

Oct 13, 2009 | 1996 Chrysler Town & Country

1 Answer

Crankshaft Position Sensor and Camshaft Position Sensor


REMOVE OR DISCONNECT

  1. Serpentine belt from the crankshaft pulley.
  2. Raise the vehicle on a hoist.
  3. Right front tire and wheel assembly.
  4. Right inner fender access cover.
  5. Using a 28 mm socket, remove the crankshaft harmonic balancer retaining bolt.
  6. Crankshaft harmonic balancer using tool J 38192 or equivalent.
  7. Sensor electrical connector.
  8. Foreign object deflector.
  9. Sensor and pedestal from block face.
  10. Sensor from pedestal.
INSTALL OR CONNECT:

  1. Loosely install the crankshaft sensor on the pedestal.
  2. Position the sensor with pedestal attached on special Tool J 37089.
  3. Position the special tool on the crankshaft.
  4. Bolts to hold the pedestal to the block face, torque to 20-40 Nm (14-28 lb.ft).
  5. Torque the pedestal pinch bolt to 3-4 Nm (38-40 lb.in).
  6. Remove special tool J 37089.
  7. Place the special tool 37089 on the harmonic balancer and turn. If any vane of the harmonic balancer touches the tool, replace the balancer assembly.
  8. Balancer on the crankshaft.
    • Apply thread sealer (GM 1052080) or equivalent to the threads of the balancer bolt.
  1. Torque the crankshaft bolt to 140 Nm + 56°(104 lb.ft + 56°).
  2. Foreign object deflector.
  3. Electrical connector.
  4. Inner fender shield.
  5. Tire and wheel assembly, torque to 140 Nm (104 lb.ft).
  6. Lower the vehicle.
  7. Serpentine belt.

Jun 02, 2009 | 1994 Buick Regal Gran Sport

1 Answer

1993 ford taurus, replaced all starting and charging componets still no spark to plugs. Checked all fuses and all fusible links. Replaced key switch, ignition switch,neutral safty...


The camshaft position sensor sends a signal to the PCM, powertrain control module. The PCM then determines spark plug firing. Could be the camshaft position sensor.

1996 is all I have
Camshaft Position (CMP) Sensor 3.0L (2V) Engine
The camshaft position sensor (CMP sensor) (12126):
  • is a single Hall-effect magnetic switch activated by a single vane which is driven by the camshaft (6250).
  • provides camshaft position information which is used by the ignition coil (12029) and the powertrain control module (PCM) (12A650) for fuel synchronization.
3.0L (4V) Engine
The camshaft position sensor (CMP sensor) (6B288) is:
  • a variable reluctance sensor.
  • triggered by the high-point mark on the LH exhaust camshaft sprocket (6256).
-----------------
3.0L (2V) Engine
SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Syncro Positioning Tool T95T-12200-A
sth~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Prior to removal of the camshaft position sensor (CMP sensor) (12126), set cylinder No.1 to zero degrees top dead center (TDC) of compression stroke. Then note the position of the camshaft position sensor electrical connector. The installation procedure requires that the connector be located in the same position.
Removal
  1. Disconnect battery ground cable. Refer to Section 14-01 .
  1. Disconnect engine control sensor wiring connector from camshaft position sensor.
  1. Remove camshaft position sensor retaining screws and camshaft position sensor from camshaft position sensor housing.
  1. If removing camshaft position sensor housing from the cylinder block (6010), proceed with Removal Step 5. If not removing camshaft position sensor housing, proceed to installation Step 6.
  1. Remove hold-down clamp (bolt and washer assembly).
  1. Remove camshaft position sensor housing from cylinder block.
Installation
  1. sth~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: A special service tool such as Syncro Positioning Tool T95T-12200-A must be obtained prior to installation of the replacement camshaft position sensor. Failure to follow this procedure will result in improper camshaft position sensor alignment. This will result in the fuel system being out of time with the engine, possibly causing engine damage.
    Attach Syncro Positioning Tool T95T-12200-A as follows:
    1. Engage camshaft position sensor housing vane into the radial slot of the tool.
    1. Rotate tool on camshaft position sensor housing until tool boss engages notch in camshaft position sensor housing.
  1. Pre-lubricate synchronizer gear with engine oil meeting Ford specification ESE-M2C123-A prior to assembly.
  1. Install camshaft position sensor housing so that drive gear engagement occurs when arrow on locator tool is pointed approximately 75 degrees counterclockwise from the rear face of the cylinder block. This step will locate camshaft position sensor electrical connector in the pre-removal position.
  1. Roatate Syncro Positioning Tool T95T-12200-A clockwise slightly. This will engage oil pump intermediate shaft. Push downward while adjusting Syncro Positioning Tool T95T-12200-A until the Syncro Gear engages the camshaft gear.
  1. When synchronizer flange is fully seated against block, the installation tool should be facing counterclockwise of engine centerline approximately 33 to 45 degrees.
  1. Install hold-down clamp (washer and bolt) and tighten bolt to 19-30 Nm (14-22 lb-ft).
  1. Remove Syncro Positioning Tool T95T-12200-A.
  1. sth~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: If camshaft position sensor electrical connector is not positioned properly, DO NOT reposition the connector by rotating the camshaft position sensor housing. This will result in the fuel system being out of time with the engine, possibly causing engine damage. Remove the camshaft position sensor housing and repeat installation procedure, beginning with Step 1.
    Install camshaft position sensor and retaining screws. Tighten screws to 1.5-4.0 Nm (13-35 lb-in).
  1. Connect engine control sensor wiring connector to camshaft position sensor.
  1. Connect battery ground cable.
824fa44.gif
Item Part Number Description 1 T95T-12200-A Syncro Positioning Tool 2 — Water Outlet (Part of Intake Assy) 3 9424 Intake Manifold 4 N602704-S Screw and Washer 5 12126 Camshaft Position Sensor 6 12A362 Synchronizer Assembly 7 12270 Hold-Down Clamp A — Tighten to 1.5-4 Nm (13-35 Lb-In) B — Tighten to 19-30 Nm (14-22 Lb-Ft)

Apr 04, 2009 | 1993 Ford Taurus

1 Answer

1997 mercury sable camshaft sensor replacement


do you have 3.L 2v or 4 valve?

3.0L (2V) Engine
SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Syncro Positioning Tool T95T-12200-A
svh~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Prior to removal of the camshaft position sensor (CMP sensor) (12126), set cylinder No.1 to zero degrees top dead center (TDC) of compression stroke. Note the position of the camshaft position sensor electrical connector. The installation procedure requires that the connector be located in the same position.
Removal
  1. Disconnect battery ground cable. Refer to Section 14-01 .
  1. Disconnect engine control sensor wiring connector from camshaft position sensor.
  1. Remove camshaft position sensor retaining screws and camshaft position sensor from camshaft position sensor housing.
  1. If removing camshaft position sensor housing from the cylinder blocks (6010), proceed with Removal Step 5. If not removing camshaft position sensor housing, proceed to installation Step 6.
  1. Remove hold-down clamp (12270) (bolt and washer assembly).
  1. Remove camshaft position sensor housing from cylinder blocks.
Installation
  1. svh~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: A special service tool such as Syncro Positioning Tool T95T-12200-A must be used to position the synchronizer assembly prior to installation of the camshaft position sensor. Failure to follow this procedure will result in improper camshaft position sensor alignment. This will result in the fuel system being out of time with the engine, possibly causing engine damage.
    Attach Syncro Positioning Tool T95T-12200-A as follows:
    1. Engage camshaft position sensor housing vane into the radial slot of the tool.
    1. Rotate tool on camshaft position sensor housing until tool boss engages notch in camshaft position sensor housing.
  1. Pre-lubricate synchronizer gear with engine oil meeting Ford specification ESE-M2C123-A prior to assembly.
  1. Install camshaft position sensor housing so that drive gear engagement occurs. Locate camshaft position sensor electrical connector in the pre-removal position.
  1. Install hold-down clamp (washer and bolt) and tighten bolt to 19-30 Nm (14-22 lb-ft).
  1. Remove Syncro Positioning Tool T95T-12200-A.
  1. svh~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: If camshaft position sensor electrical connector is not positioned properly, DO NOT reposition the connector by rotating the camshaft position sensor housing. This will result in the fuel system being out of time with the engine, possibly causing engine damage. Remove the camshaft position sensor housing and repeat installation procedure, beginning with Step 1.
    Install camshaft position sensor and retaining screws. Tighten screws to 1.5-4.0 Nm (14-35 lb-in).
  1. Connect engine control sensor wiring connector to camshaft position sensor.
  1. Connect battery ground cable.

Feb 22, 2009 | 1997 Mercury Sable

1 Answer

1990 ford tempo 86K going down interstate, engine shuts down, will not restart. recentl plugs, oil change. Help


If it will restart after it cools down then it might be the camshaft positioning sensor. It will be located beside the oil filter on the block. If this part is cracked it will short out as the car heats up and cause the computer to shut the car down.

Jul 18, 2008 | 1994 Ford Tempo

1 Answer

1992 ford tempo 2.3L diagnostic code 10 what does it mean?


Code PO10 has to do with the "Camshaft Position Actuator circuit Bank 1" an actuator is a relay,solenoid or motor that send a signal to the cumputer that something is wrong.i think in this case it is the Camshaft Position Sensor or the camshaft interrupter magnet. Probably the sensor has to be replaced. It is located on the engine block.

Jun 28, 2008 | 1992 Ford Tempo

Not finding what you are looking for?
1994 Ford Tempo Logo

131 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

63291 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...