Question about 1999 Hyundai Accent

1 Answer

WINDOW CRANK HANDLE

I need to get the door panel off to see why the window is very hard to roll down and I can't see how to remove the window crank handle.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 10 Answers

There will be a wire clip at the back of the winder, you will be able to push this out using a trim fork, or 2 thin screwdrivers.

Posted on Oct 22, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Remove citroen c3 rear door panel


Check out how the door panels are attached to the car. Most panels use screws and bolts but others have snap-in fittings. Gather all the tools you need for removing the door panels. If the panel is attached with screws and bolts, you need a screwdriver or ratchet and socket. Car door panels with snap-in fittings are easily removed with a flathead screwdriver.
Locate where the screws and bolts are before starting. These are usually found in the arm rest area, along the bottom or sometimes near the door lights.
Roll down the car door window. Begin removing all screws and bolts that hold the door panel onto the car. If your car has snap-in fittings, pry gently on the bottom corner of the door panel until the fittings pop out.
Remove the power window control panel if your car has power windows. The control panel should pry out easily, and then you unplug the wiring harness from the back and place it to the side.
Use an L pick and flashlight when locating a manual window crank. Look behind the window crank and slide the pick under the edge of the metal clip that holds the crank in place. Remove the clip and pull the crank off.
Remove the door handle by unscrewing the small screw located in the center. Gently pull the door handle out until you see the back of the handle and unclip the rod from the door handle. This should remove the handle unless the handle and door lock are attached, then you just unclip the rod from the lock and remove them both together.
Unscrew the cap off rear upper corner door panel locks. These don't have a rod attaching them to the handle and unscrew separately from the door handle.
Pop the door panel off after you've removed everything. Gently pry on the bottom edge of the door panel until it releases. Pull out and up to completely remove the door panel.
GM Tech2 GM Diagnostic Scanner with 32MB Card and TIS2000

Oct 10, 2014 | 2006 Citroen C3 1.4i

1 Answer

How do i take off the inside drivers door panel on a 2005 dodge caravan


Hi Roberta, here's the instructions on how to remove your door panel. I have to wonder though on why you are removing it, my guess is you window doesn't roll up or down and your replacing the regulator. Any way here goes.

REMOVAL

  1. Remove the plug and remove screw attaching door pull cup to inner door panel.
  2. Remove switch bezel and disconnect power window/memory switch.
  3. Remove screws attaching trim panel to door from below map pocket.
  4. If equipped, remove window crank. (Refer to 23 - BODY/DOOR - FRONT/WINDOW CRANK - REMOVAL)
  5. Remove screw holding door trim to door panel from behind inside latch release handle .
  6. Disengage clips attaching door trim to door frame around perimeter of panel.
  7. Lift trim panel upward to disengage flange from inner belt molding at top of door.
  8. Tilt top of trim panel away from door to gain access to latch linkage.
  9. Disengage clip attaching linkage rod to inside latch release handle (INSIDE DOOR HANDLE LINKAGE).
  10. Separate linkage rod from latch handle.
  11. Disconnect the power door switch, courtesy lamp electrical connectors.
  12. Remove front door trim panel from vehicle.
Hope this helps and have an awesome day Roberta!

May 21, 2014 | 2005 Dodge Grand Caravan

2 Answers

How do I remove the handle in door panel? I'm trying to remove the door because my window fell off the track, it doesn't have power windows so I have to manually roll them up and down.


1- remove the window crank
2- remove any screws from the door panel; sometimes they are hidden by a plastic cap. look inside the elbow rest cavity; remove any screws you see.
3- insert a flat plastic or wooden tool in the shape of (roughly) a scraper, between the door panel and door and start prying the clips which hold the panel to the sheet metal. get as close to the clips as possible with the tool, as that will be the easiest way. there are about 8 of these clips on an average door. when all the clips have come loose of the sheet metal, lift the panel straight up to remove it. you will find a metal rod attached to the inside of your handle; unfasten it and remove the panel completely. that handle looks like it is part of the panel and cannot be removed separately.

Mar 15, 2013 | Cars & Trucks

2 Answers

Door panel removal


To remove the window crank slip a small standard screwdriver behind where the crank mounts to the door.There is a small spring like c-clip pop the clip off and cran Window Handle Operation:
00457_window_handles.jpgReplacement handle for cranking or rolling a side or rear window up or down. It slides over the window crankshaft and uses splines to match the window crank shaft splines as to avoid slippage. It's held in place with a simple spring clip and come in a variety of styles and colors.k will come off.

Jun 27, 2012 | 1994 Suzuki Swift

3 Answers

2000 neon manual windows don't roll down, crank turns but window doesn't move


you need a window regulator you need to take the door apart to be sure

Jan 25, 2012 | Dodge Cars & Trucks

1 Answer

How to remove the inside door panel from a dodge 2005 2500 pick up


FRONT DOOR TRIM PANEL - REMOVAL
Release door latch and open door.
Roll window down.
Remove window crank Window Crank - Typical , if equipped.
Remove screws attaching trim panel to door Door Trim Panel and Trim Panel Screw
CAUTION: Do not forcibly pull trim panel from door, damage to trim panel may occur.

Simultaneously lift upward and outward to release retainer steps from inner door panel Trim Panel Retainer
Disengage inside handle linkage rod from inside handle.
Disconnect speaker harness wire connector Speaker And Power Mirror Connector
Disengage power mirror wire connector, if equipped (driver's side only) Speaker And Power Mirror Connector
Disengage clips attaching power window/lock switch panel to door trim panel. Disengage wire connector from switch panel, if equipped Power Door Lock/Window Connector
Separate door trim panel from vehicle.
INSTALLATION
Position trim panel at door.
Engage wire connector for window/lock switch panel, if equipped. Engage clips attaching power window/lock switch panel to door trim panel.
Engage power mirror wire connector, if equipped.
Connect speaker harness wire connector.
Engage inside handle linkage rod to inside handle.
Align trim panel retainer steps with inner door panel and slide trim panel into place.
Install screws attaching trim panel to door.
Install window crank, if equipped.

Hope helped with this; remember rated this help. Good luck.

Nov 12, 2009 | 2005 Dodge Ram 2500 Truck

1 Answer

Inside door handle doesn't work (removing the driver side panel)


If you have power windows start by disconnecting your negative battery cable. Then you need to locate and remove the screws that hold your door handles in place (they may be hidden by snap in, or snap on clips). Once you remove the screws that hold the door handles, remove any wire connectors to the handles, if they're not power you will need a small hook (kinda like a knitting needle) to remove the window crank. A manual window crank is held in place by a clip on the base. Slide the hook behind the base and remove the clip. The door panel itself, is held on by snap in clips, and you will need a small pry bar to pull them from the door (try to gat as close to, or directly under the clips to prevent them from tearing out of the door panel). Once the clips are removed from the door, pull the panel upward to remove it from the door.

Install in reverse.

I hope this helps you, and I wish you luck on your repair.

May 04, 2009 | 1992 Chrysler New Yorker

1 Answer

Driver's side interior door handle snapped off


there is plastic snaps that attatch the panel to the door all the way around the panel which you can buy a tool to remove the panel without breaking the snaps,the door handle may have a cable hooked to it that releases the latch and it might be stretched causing the handle to pull hard

Apr 24, 2009 | 1989 Ford F 150

1 Answer

How to remove door panel for driver and passenger side doors


Hi. This Guide will help you with this issue.



Step1 Check out how the door panels are attached to the car. Most panels use screws and bolts but others have snap-in fittings. Gather all the tools you need for removing the door panels. If the panel is attached with screws and bolts, you need a screwdriver or ratchet and socket. Car door panels with snap-in fittings are easily removed with a flathead screwdriver. Step2 Locate where the screws and bolts are before starting. These are usually found in the arm rest area, along the bottom or sometimes near the door lights. Step3 Roll down the car door window. Begin removing all screws and bolts that hold the door panel onto the car. If your car has snap-in fittings, pry gently on the bottom corner of the door panel until the fittings pop out. Step4 Remove the power window control panel if your car has power windows. The control panel should pry out easily, and then you unplug the wiring harness from the back and place it to the side. Step5 Use an L pick and flashlight when locating a manual window crank. Look behind the window crank and slide the pick under the edge of the metal clip that holds the crank in place. Remove the clip and pull the crank off. Step6 Remove the door handle by unscrewing the small screw located in the center. Gently pull the door handle out until you see the back of the handle and unclip the rod from the door handle. This should remove the handle unless the handle and door lockmag-glass_10x10.gif are attached, then you just unclip the rod from the lock and remove them both together. Step7 Unscrew the cap off rear upper corner door panel locks. These don't have a rod attaching them to the handle and unscrew separately from the door handle. Step8 Pop the door panel off after you've removed everything. Gently pry on the bottom edge of the door panel until it releases. Pull out and up to completely remove the door panel.


Please rate and have a great day:)

Mar 25, 2009 | 2002 Kia Optima

1 Answer

Manual window won't roll up


so is the right rear door ??
if so here are some instructions.
  1. If applicable, remove the regulator handle by pulling the clip out with a wire hook.
  2. Remove the inside door handle and disconnect the latch rod.
  3. Remove the screws and detach the clips attaching the door panel (see trim pad remover.
  4. Disconnect the power window and courtesy light harnesses.
  5. Remove the door panel bracket and carefully remove the plastic cover
  6. Remove the screw attaching the door lock crank. Disconnect the latch rod from the latch side.
if you have an email address i can send some images on how to do it.
hope this helps

Jun 07, 2008 | 1991 Honda Accord

Not finding what you are looking for?
1999 Hyundai Accent Logo

241 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...