Question about 1997 Ford Windstar

2 Answers

Camshaft sensor where is the camshaft sesor located on a 3.0L 1997 ford windstar?

Posted by on

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Night Owl:

    An expert who has answered 10 or more questions between 12 midnight and 6am on the same day.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 173 Answers

The camshaft position sensor is located at right rear
of the engine where the distributor was in the old cars

Posted on May 02, 2013

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 49 Answers

It is located at the right rear of the engine block. It has a plug with three wires in it. Hope this helps.

Posted on Feb 25, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Won't start


Does engine turns at all and just won't start?

Dec 16, 2013 | 1997 Ford Windstar

1 Answer

Ford windstar problems


try the auto shufoff relay..this controls the fuel pump..

Dec 16, 2013 | Cars & Trucks

1 Answer

Where is the camshaft sensor located on a 1997 Ford T Bird LX 4.6


The camshaft position sensor is on the left (drivers) side on the front cover

Aug 22, 2012 | Cars & Trucks

1 Answer

Obd code p0171 and p0174 for 2003 ford windstar


check the camshaft position sensor and the O2 sensors ,the fuel filter and try use of a good fuel sistem cleaner .

Jul 22, 2012 | 2003 Ford Windstar

1 Answer

Code P1309 on a Ford Winstar 1999 3.8 lts. Mexico


Code PO1309 : Misfire Monitor Failure Description : When the misfire monitor is disabled,usually due to the input signal generated by the camshaft position sensor, by sensing the passage of teeth from the camshaft position wheel. Possible Causes : PCM(power train control module), Mass Air Flow Sensor, Engine Coolant Temperature Sensor, Crank Shaft Position Sensor, Camshaft Position Sensor.

Jun 01, 2011 | 1999 Ford Windstar

1 Answer

96 ford Windstar lx fuelinjected v6 3.8 it turns over but wont run like no gas??


CHECK FUEL PUMP FUSE AND RELAY.IF BOTH ARE GOOD.CHECK THE FUEL PUMP INERTIA SWITCH MAKE SURE IT HAS NOT TRIPPED OFF. INERTIA SWITCH LOCATION IN THE SPARE TIRE JACK COMPARTMENT.IF ALL LOOK GOOD SCAN CAR FOR PCM FAULT CODE OR CRANKSHAFT SENSOR AND CAMSHAFT SENSOR FAULT CODES.

Jun 12, 2010 | 1996 Ford Windstar

1 Answer

1997 ford windstar


IN THE PASSENGER WHEEL WELL YOU WILL HAVE TO REMOVE THE REAR MOTOR MOUNT TO GET TO IT...AND MAKE SURE THE ENG..IS COLD .....

Sep 28, 2009 | 1996 Ford Windstar

1 Answer

1998 Ford Windstar, no start with out pushing on throttle, some times not then, runs ok after it starts. have codes, PO340 & PO401


po401 is egr flow insufficiant ( the egr needs removed and cleaned also clean where it mounts to engine. po340 is camshaft position sensor A- bank 1 curcuit malfunction. it is a bad camshaft sensor.

Sep 20, 2009 | 1998 Ford Windstar

Not finding what you are looking for?
1997 Ford Windstar Logo

Related Topics:

445 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...