Question about 2000 Hyundai Elantra

1 Answer

Auto gearbox 1998 Hyundai 2000cc

Hi

I have just bought a 2 litre Hyundai coupe with an autobox. The problem I am having is when you put it in drive it pulls away as normal but then as you pick up speed flicks back to neutrel and sometimes cuts out as a result.
It drives ok normally in the lower gears but as soon as you pick up speed the problem starts.
I have asked around a few mechanics but none of them have any autobox epierence.

Please note I have not selected the right product as it was not listed the car I have is a hyundai Coupe not an Elantra.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Hyundai Master
  • 21,550 Answers

Probably needs a gearbox rebuild. Take it to a specialist or you may waste a lot of money using odd job mechanics.

Posted on Apr 27, 2017

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

emissionwiz
  • 75822 Answers

SOURCE: removal of gearbox cv joint

It just pulls out of the geat box, it has a internal snap ring, they can really bwe a bear if they're being pulled for the first time.

Posted on Dec 09, 2008

SOURCE: Hyundai Coupe gearbox ( not car in product)

hi there! i was a master tech 4 hyundai, first of all has the atf fluid been changed and at the correct level. or have you had the multifuntion switch checked? please feel free to contact myself and i will advise you as required with my exsperience

many thanks

Dominic Hill

Posted on Dec 11, 2008

BCally1
  • 133 Answers

SOURCE: Rear hub nut torque setting Hyundai coupe 2000 se

65-80 ft.lbs

Posted on Jan 06, 2009

  • 87 Answers

SOURCE: 2002 Hyundai Coupe 2.7L V6 clutch problem

Hi what your going to have to do is. unhook your slave cly and take a pry bar and pry the fork bar towards the front of the car you will hear a click. that means you have poped the throw out bearing into the plate. You did nothing wrong they just have to be popped in.

Posted on Mar 28, 2009

  • 510 Answers

SOURCE: Remote control receiver unit were is it , and a

This reset for key fob Hyundai coupe year 02 to 04
Turn ignition to position two
Press lock or unlock once
Ensure indicators flash once to confirm reset
This will enable fob providing you have no other faults
Good luck barry

Posted on May 12, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have had a light come up on my bm3 3 series coupe auto the symbol looks like a gear cog with a caution symbol inside it ?


Hi, if you have manual gear box then it could mean your clutch needs replacing or the gearbox oil is low

if you have autobox then it could indicate you need to get the fluid and filter changed

hope that is some help to you

if you have the owners handbook if you look in their it will tell you exactly what each warning light means and the kind of problems its highlighting

Aug 19, 2010 | BMW 328 Cars & Trucks

1 Answer

Remote control receiver unit were is it , and a pic of it to reset key fob on a hyundai coupe se 2000cc year 2002


This reset for key fob Hyundai coupe year 02 to 04
Turn ignition to position two
Press lock or unlock once
Ensure indicators flash once to confirm reset
This will enable fob providing you have no other faults
Good luck barry

May 12, 2010 | 2003 Hyundai Tiburon

1 Answer

Why does my auto gearbox not go into 4th when the overdrive is not on or off on my hyundai coupe se 1998


Sounds to me like u have a faulty ( pulse generator sensor) u can find it at a dealership for less than 80 dlls. it can be easly replace by anyone its : a 1 plug conector wire that divides into 2 sensors like a ( Y ) ull find it under the air filter right on top of the transmission just follow the wire and ull find the second sensor under the transmision, once replaced, i let the key to on position for 15 min to reset the computer ,and ur good to go..car runs like new again..hope this helps ... Marcos

Feb 24, 2010 | Hyundai Motor 1998 Accent

1 Answer

1997 Jaguar XK8 "Gearbox fault" (Auto) doesn't want to go


I'm not familiar with the jag but my ford is similar( no dipstick). I'm led to believe these are designed to prevent overfilling, which can blow out the seals. I undo the top pipe which goes to my radiator to cool the trany fluid, then get a 1/2 metre length of plastic tube to fit between the disconnected pipe and a 1 litre bottle of fluid. I then squeeze the fluid in that way....no more than a litre at a time, then try driving it again..Hope this helps.

Sep 11, 2009 | 1998 Jaguar XK8

1 Answer

Correct tyre pressure hyundai accent coupe i


DEPENDING ON TYPE OF TYRES IT SHOULD BE 2.2BAR LOOK ON THE TYRE PRESSURE IS PRINTED ON THE TYRE

Jun 30, 2009 | Hyundai Motor 1998 Accent

1 Answer

Hyundai coupe 2000cc loses power


I had the same problem,it was the hopper tank in the main fuel tank it was not staying full of fuel when the tank was at 1/3 full or less,in my case there was debris in the jet pump causing the pump to not pump.mine wasnt a hyundai but your problem is within your fuel tank.

Apr 18, 2009 | 2003 Hyundai Tiburon

3 Answers

Where is the reversing light switch on a vauxhall vectra 2 litre auto 1996


it is just under u gearstick gator or cover u mayneed to take center consol out to get to it

Mar 19, 2009 | Hyundai Motor 1995 Accent

1 Answer

2002 Hyundai Coupe 2.7L V6 clutch problem


Hi what your going to have to do is. unhook your slave cly and take a pry bar and pry the fork bar towards the front of the car you will hear a click. that means you have poped the throw out bearing into the plate. You did nothing wrong they just have to be popped in.

Mar 02, 2009 | 2003 Hyundai Tiburon

1 Answer

Hyundai Coupe gearbox ( not car in product)


hi there! i was a master tech 4 hyundai, first of all has the atf fluid been changed and at the correct level. or have you had the multifuntion switch checked? please feel free to contact myself and i will advise you as required with my exsperience

many thanks

Dominic Hill

Dec 09, 2008 | 1998 Hyundai Elantra

1 Answer

Removal of gearbox cv joint


It just pulls out of the geat box, it has a internal snap ring, they can really bwe a bear if they're being pulled for the first time.

Nov 23, 2008 | Hyundai Motor 1998 Accent

Not finding what you are looking for?
2000 Hyundai Elantra Logo

Related Topics:

38 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8215 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...