Question about 2000 Dodge Durango

1 Answer

Oil pan How to remove the oil pan on 2000 Dodge Durango? The pan is lose it just will not drop out.

Posted by on

  • Anonymous Mar 15, 2014

    how do I get it out ive separated the gasket from pan but cant get it out

  • Anonymous Mar 15, 2014

    ive separated the gasket from pan but cant figure out the rest of the way to pull it off

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Governor:

    An expert whose answer got voted for 20 times.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 11 Answers

Have you tried getting a screw driver and prying at it?

Posted on Oct 21, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace oil pump un an a 2007 dodge durango 5.7 hemi motor


the oil pump is located inside the oil pan. removing the motor will be needed to do the job unless you got a new way to open the oil pan with everything in the way. if you have really low or no oil pressure. or after driving for a few miles the pressure drops a lot. the bearings could also be gone and that is going to need to be address with the motor out. other option is get a junkyard motor and replace it. but you never know what could be wrong with that motor. try to hear the engine run if possible

Feb 12, 2015 | 2007 Dodge Durango

1 Answer

How to remove oil pan on a 2004 dodge durango


You have to Unbolt the engine mounts and lift the engine, Unbolt the oil pan and rotate the crankshaft by hand to get it to clear the counterweight on the crank. If the engine has 100,000 miles or more replace the oil pump while your in there.

Dec 02, 2014 | Dodge Durango Cars & Trucks

1 Answer

2004 dodge durango 5.7 lt engine oil pan removal


loosen nuts on the botom of pan drop it the put new one back on

Oct 28, 2013 | 2000 Dodge Durango

1 Answer

I need to know how to remove my oil pan from my 2000 dodge dakota v6 magnum 3.9 lt truck , got the bolts off and the engine mounts removed but oil pan will not come off, plz help. thx


they get stuck on there really good, i have a 2000 durango, and i had tu use a scredriver, and hammer around it, it was so stuck by the time i got it off of there, i had ro replace the pan it was so bent around the lip.... you could use a screwdriver and hammer between the pan and engine, try to barely tap it the screwdriver between them, all the way around the pan.. hope you have better luck than i did..

Dec 03, 2010 | Dodge Dakota Cars & Trucks

1 Answer

Does my 2000 Dodge Durango have an oil leak?


Good Evening, its a good question that only you can give the answer for. And if you have oil underneath your durango on the ground and there is oil on your oil pan then I would agree you do. However they are also known to leak between the transfer case and the transmission so you might look there as well. Hope this helps since you have a little more information on the condition of your durango than i do. :-)

Aug 28, 2010 | 2000 Dodge Durango

1 Answer

2000 Durango: oil pressure works for a few minutes then drops to...


What engine in your Durango? Most likely you have debris on your oil pan clogging the pickup screen, or a failing pump.
Be sure to verify with a mechanical pressure gage that oil pressure is indeed dropping before you take oil pan off.

May 17, 2010 | 2000 Dodge Durango

1 Answer

Im having a hard time getting the oil pan off of a 2003 Dodge Durango, 5.9 4wheel drive.


The frame is in the way and you have to lift the engine to remove the pan.
  1. Turn on the Durango and run it for at least 10 minutes, a few times around the block is best. This will get the engine oil up to temperature allowing it to drain better for you.Park the vehicle on a flat, stable surface that gives you enough room to move around under. Jack up the Durango following the directions provided with your jack and jack stands.Open the hood of the Durango and located the engine oil cap, found on the right side of the engine, towards the middle. Remove the cap by twisting it off and set aside, allowing ventilation and pressure release.Climb under the vehicle and located the oil pan. The oil pan is on the underside of the engine, between the car's tires. It is a rectangular shaped pan with a plug located on the end towards the back of the car.Place an oil drip pan under the oil pan and pull the plug by twisting it and pulling it. This will release all oil from the vehicle, draining it into the pan below. Allow the oil to drain until there is nothing left coming out.Use a wrench to loosen the bolts of the oil pan. There are a total of 17 of them located around the edge of the oil pan, connecting it to the frame of the engine. Store safely.Remove the oil pump pickup tube and oil pan gasket, which are connected to the oil pan. You will find these as soon as you drop the oil pan.
    to Replace the Oil Pan Gasket in a Dodge Durango
    1. Jack up the front of the Dodge Durango, and install a jack stand. Block the rear wheels. Remove the oil plug and let the oil drain into a pan, being sure to remove as much of the old oil as possible.Loosen the bolts holding the oil pan with a socket wrench, and remove the bolts with your fingers. Remove the oil filter, starter motor, cooler lines, oil level sensor, heated oxygen sensor connector and exhaust y-pipe, and then take off the oil pan.Scrape off the old gasket with a thin putty knife, being very careful not to scrape the surface. Be sure all of the old gasket is removed, then wipe the surface with solvent. Spread a bit of oil on the surface to promote adhesion, and apply the new gasket.Replace the oil pan, exhaust y-pipe, heated oxygen sensor connector, oil level sensor, cooler lines and starter motor, and install a new oil filter.Raise the vehicle slightly with the jack and slide out the jack stand before lowering the vehicle and removing the jacks.Fill the engine with the appropriate amount of oil. Check the level with the dipstick to be sure you have the right amount.
      this will help.thanks.

Feb 21, 2010 | 2003 Dodge Durango

4 Answers

2000 dodge durango 5.2 engine oil gauge drops down to zero...


Hi. this sounds like the oil pressure sending unit may be malfunctioning. could be a bad module or a lose connection. the second issue that may be the primary issue can be a faulty oil pump. you will find the problem in these two areas.

Please rate and god bless:)

Apr 02, 2009 | 2000 Dodge Durango

1 Answer

360 motor losing oil pressure after15min of running


Try hooking up a mechanical gauge to make sure you have a problem.

Feb 27, 2009 | 2000 Dodge Durango

1 Answer

I have a 2000 dodge durango 360 that once it runs loses oil press


if there is no knocking noise then replace the oil sending switch this should fix your problem let me know

Feb 22, 2009 | 1997 Dodge Ram 1500 Club Cab

Not finding what you are looking for?
2000 Dodge Durango Logo

Related Topics:

476 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...