Question about 1985 Toyota Land Cruiser

1 Answer

85 landcruiser wagon auto procedure for checking auto fluid.

What is the procedure for checking auto fluid? is it with engine running or just after stopping or cold etc

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Toyota Master
  • 1,861 Answers

Engine running, in park, with the engine at operating temperature (temp gauge at the normal reading, or coolant at 192 degrees F.)

Posted on Oct 21, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Liftertick 85 gl wagon how to fix


One chance. Warm the engine, put 1/2 quart of transmission fluid in the engine and let it run for abut 30 minutes at idle. If the tick doesn't go away. You can replace the rocker arms, push rods and lifters. Some cases , you have to replace the cam shaft also. Make sure you replace the engine oil after this.

Apr 10, 2016 | Cars & Trucks

1 Answer

To start with my power steering pump was making a little noise and also had bubbles in the resevoir so i put a new power steering pump on it.not a rebuilt one. when i started it up i still have the bubbles...


Section 11-00: Steering System-Service 1999 Taurus, Sable Workshop Manual SERVICE PROCEDURES Purging Power Steering System of Air NOTE: If the air is not purged from the power steering system correctly, a second customer concern or pump failure could result. This condition can only occur on pre-delivery vehicles with evidence of aerated fluid or vehicles that have had steering component repair.

A whine noise heard from the power steering pump may be caused by air in the system. The following procedure must be performed whenever any of the following are performed:
  • All power steering noise complaints with evidence of aerated fluid on pre-delivery vehicles only, prior to any component repair.
  • After any power steering system component (for example, gear or hose) has been replaced and the noise is heard.
Fluid Level Top-Off Procedure
  1. Check and fill pump reservoir to dipstick full cold or remote reservoir center mark.
  1. Disable ignition by removing Fuse 10 in the fuse junction panel.
  1. Crank engine 30 seconds, check fluid level and add if required.
  1. NOTE: Do not hold steering wheel on stops.

    Crank engine 30 seconds while cycling the steering wheel lock to lock.
  1. Check fluid level and add fluid if required.
Air Purge with Vacuum External Source Procedure - 3.0L (2V) Engine, Flex Fuel and 3.4L SHO Engine
  1. Tightly insert the rubber stopper of the air evacuator assembly into pump reservoir.
  1. Reinstall Fuse 10 used to disable ignition and start vehicle.
  1. Apply 20-25 in-Hg (85-88 kPa) maximum vacuum for minimum of three minutes at idle; maintain maximum vacuum with vacuum source.
  1. Release vacuum and remove vacuum source.
  1. Add fluid to full warm or reservoir center mark.
  1. Reinstall vacuum source and apply 20-25 in-Hg (85-88 kPa) vacuum.
  1. NOTE: Do not hold steering wheel on stops.

    Cycle steering wheel from lock to lock every 30 seconds for approximately 5 minutes.
  1. Shut engine off, release vacuum and remove vacuum source.
  1. Add Motorcraft MERCON Multi-Purpose (ATF) Transmission Fluid if necessary and install dipstick or reservoir cap.
  1. NOTE: Do not hold steering wheel on stops.

    Start engine and cycle steering wheel from lock to lock every 30 seconds for approximately 5 minutes.
  1. Check for oil leaks at all connections.
  1. In severe cases it may be necessary to repeat air purge with vacuum source procedure.
Air Purge with Vacuum External Source Procedure - 3.0L (2V) and 3.0L (4V)
  1. Add Motorcraft MERCON® Multi-purpose (ATF) Transmission Fluid XT-2-QDX or MERCON® equivalent to approximately 2.5 cm (1 in) (make a mark) above the top of the supply line.
  1. Tightly insert the rubber stopper of the air evacuator assembly into the pump reservoir.
  1. Apply 85-88 kPa (20-25 in-Hg) maximum vacuum for a minimum of three minutes.
  1. Add Motorcraft MERCON® Multi-purpose (ATF) Transmission Fluid XT-2-QDX or MERCON® equivalent until the level is at the marked point.
  1. Repeat Steps 3 and 4 until the fluid level stabilizes.
  1. Check reservoir level and add Motorcraft MERCON® Multi-purpose (ATF) Transmission Fluid XT-2-QDX or MERCON® equivalent to the FULL WARM (MAX) mark.
  1. Install the number 10 fuse in the fuse junction panel. Start the engine.
  1. NOTE: The front wheels must be off the floor during lock-to-lock rotation of the steering wheel.

    NOTE: Do not hold the steering wheel on stops.

    Reinstall the vacuum source and apply 85-88 kPa (20-25 in-Hg) maximum vacuum and cycle the steering wheel from lock-to-lock every thirty seconds for a minimum of 5 minutes.
  1. Shut the engine off, release the vacuum and remove the vacuum source.
  1. Add Motorcraft MERCON® Multi-purpose (ATF) Transmission Fluid XT-2-QDX or MERCON® equivalent to the FULL WARM (MAX) level. Install the dipstick or reservoir cap.
  1. NOTE: Do not hold the steering wheel on stops.

    NOTE: In severe cases, it may be necessary to repeat air purge with vacuum source procedure.

    Start the engine and cycle the steering wheel from lock-to-lock every thirty seconds for approximately five minutes.
  1. Lower the vehicle front end.
  1. Check for oil leaks at all connections.

Jul 24, 2011 | 1999 Ford Taurus

2 Answers

My 1997 chevy 1500 z71 brakes suddenly going all the way to the floor. Checked brake fluid and it was low. Could be wheel cylinder? Master cylinder? or ?


well, check the brake lines for leakage after adding brake fluid to the full mark. If the brake pedal goes all the way to the floor, it's likely there is a leak somewhere after the master cylinder. If the pedal gets hard after adding fluid, and pumping it several times with the car off, then the master cylinder is still ok.

If air has gotten into the master cylinder, it may have to be bled out on a bench, or using a scanner if that's the way your vehicle is.

Bleeding the Brake System (ABS) Auto Bleed Procedure NOTE: Perform a manual bleeding procedure. If the brake pedal height and firmness results are not achieved, perform the auto bleed procedure below.
NOTE: Perform this procedure when replacing the brake pressure modulator valve or electro-hydraulic control unit.
  1. Perform the manual brake bleeding procedure. Refer to Bleeding the Brake System (non-ABS).
  2. Check the master cylinder fluid level often to prevent running the system dry.
  3. Press the brake pedal firmly and run the Scan Tool Automated Bleed Procedure (for Gas engines) once, or the Function Test (for Diesel engines) four times. Make sure to release the brake pedal between each test.
  4. Perform the manual bleed procedure again. This should remove the remaining air from the brake system.
  5. Bleed the system as many times as needed to obtain the appropriate feel of the brake pedal.

Dec 18, 2010 | 1997 Chevrolet K1500

1 Answer

Automotive problem. 1991 Subaru Legacy C


Lubricant may not resolve it sounds like it could be your water pump froze up. Look to see if it is turning. Even if it turns it still could be bad.Usally the first sign of it going bad. Stop by your local auto parts store to see if they agree.

Dec 28, 2009 | 1991 Subaru Legacy

1 Answer

I have a 1983 Mercedes 300 TD wagon that slips when shifting from 2nd to 3rd gear, is there an adjustment in the trans or a good additive that will help with this problem, walter


Dear Walter.There is not a lot you can do to an auto trans except check the level of the fluid.Run it through all the gears and put it in neutral.Make sure the engine is warm.Now check the fluid level.Top it up through the same tube as the dipstick for the tranny.Hope this helps

Oct 24, 2009 | 1983 Mercedes-Benz 300-Class

1 Answer

2002 a4 audi wagon 150.000 miles


The tranny fluid dipstick should be at the back of the motor. Take the car to Auto Zone and have them run a dianostic on it. It will tell you what codes are being thrown up from the computer. That should get you started.

Mar 01, 2009 | 2002 Audi A6

1 Answer

Landcruiser auto transmission,,how to check fluid level


when you open your hood look in the back of the motor on the left side.. you should see a stick with a circle on the end of it for your finger have you vehicle running warmed up that means let it run for 10 or 15 min. and then pull the stick out.. wipe it off real good. stick it back in all the way.. pull it back out and hold it horizontally and check it.. it's sometimes hard to read because it has bubbles on it.. try it a couple of times to get an accurate reading good-luck ray

Jan 16, 2009 | 1989 Toyota Land Cruiser

1 Answer

Temperature gauge shows hot but the engine is normal operating te


replace temp sensor for the emission system. there are two on the engine.

Dec 26, 2008 | 1997 Subaru Legacy

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

100 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...