Question about 1999 Audi A4

1 Answer

Degrees of C

All measurement goes to F (Faradey) in my cars, and how I back that in degrees of Celsius (C)?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,586 Answers

Hold down the recirc button and the (-) button or the (+) button below the temp display (on the left) - one of those combinations will change it. I don't think you have to have the system off for it to work, but I'm not positive - try it out and you'll see which way works.

Posted on Oct 25, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Mariva 1.4. Why does temperature gauge reading fluctuate?


check grill and radiator fins are not plugged and fan is not damaged and is working.
sounds like a thermostat or water pump issue.

Jan 09, 2016 | Vauxhall Cars & Trucks

1 Answer

Torque cylinder


40 nm, 60 nm, then 90 degrees then 90 degrees in a bowtie pattern.

Nov 13, 2013 | Cars & Trucks

1 Answer

How to do a wheel alignment


nearly impossible but there are some things that you can do to reduce tyre wear.. 1---place the wheels in the straight ahead position. Using a spirit level place it vertical across the front rims touching only the rim top and bottom . adjust to achieve the bubble just touching on the outer line. That should give you about 1/2 to 1 degree camber. next measure with a tape the distance between the left and right rims 1/2 way up on the front of the rim. Record this measurement. Repeat the measuring at the back of the front rims at the same level as the front measurement was taken Adjust the tie rod ends evenly until the front measurement is anout 1/8 to 1/4 " smaller than the rear measurement. This is the toe in/ out measurement. The caster adjustment you will need a caster angle gauge. They are available and they stick on the hub center. and measure the difference in degrees from full left to full right turn. It need to be about 1 to 1&1/2 degrees positive.. It would be cheaper on the tyres to have the alignment done professionally and a sight quicker.

Apr 04, 2013 | Subaru Impreza Cars & Trucks

1 Answer

What are the torque specs on a 2000 Nissan maxima head


14179124-0r3idicjw2hp5z0o4sqjrbpc-4-0_0.gif


14179124-0r3idicjw2hp5z0o4sqjrbpc-4-1.gif
NOTE
If possible, replacement of the head bolts is suggested.
  1. If replacement of the head bolts is not possible, perform the following bolt measurement:
    1. Measure the diameter of the head bolt 0.43 in. (11mm) from the bottom of the bolt.
    2. Measure the diameter of the head bolt 1.89 in. (48mm) from the bottom of the bolt.
    3. Whenever the size difference between the 2 measurements exceeds 0.0043 in. (0.11mm) the head bolts must be replaced.
  2. Install the cylinder head bolts and torque in sequence as follows:
    1. Step 1: 72 ft. lbs. (98 Nm).
    2. Step 2: Completely loosen all bolts.
    3. Step 3: 25-33 ft. lbs. (34-44 Nm).
    4. Step 4: plus 90-95 degrees clockwise.
    5. Step 5: plus 90-95 degrees clockwise.

Aug 30, 2012 | Cars & Trucks

1 Answer

The torque specs for a 1999 4.6 liter northstar camshaft cap bolts


Hello: The following is straight from the 1999 4.6 service manual----Install the bearing caps according to the identification marks. The arrow should point toward the front of the engine. the number indicates the position from the front of the engine and the I or E indicates intake or exhaust camshaft. hand start all bolts. Tighten to 44 lb. in. plus 30 degrees Start from front and work back. A torque angle meter is used to measure degrees.

Sep 18, 2010 | Cadillac Cars & Trucks

2 Answers

Where does the crank shaft sensor go


Sit in back of the harmanice balancer.

Jul 14, 2010 | 1992 Chevrolet Lumina

2 Answers

I WANT TO CONVERT DEGREES INTO FT/LB TORQUE AS MY ELECTRONIC ANGLE TORQUE TOOL CANT GET INTO SOME TIGHT SPOTS SO WAS GOING TO USE TORQUE WRENCH.


I don't think that can be done because a torque wrench measures torque, or tightness. A torque angle gauge only measures the amount of degrees that the bolt is turned in relationship to 360 degrees. Auto Zone has a small torque angle gauge that may work in a tight spot.

Apr 27, 2010 | 2006 Chevrolet Silverado 2500HD 2WD

1 Answer

What is a linear pair and vetical angle.


A linear pair of angles is formed when two lines intersect. Two angles are said to be linear if they are adjacent angles formed by two intersecting lines. The measure of a straight angle is 180 degrees, so a linear pair of angles must add up to 180 degrees.

A pair of angles is said to be vertical if the angles share the same vertex and are bounded by the same pair of lines but are opposite to each other. Such angles are congruent and thus have equal measure

Sep 15, 2009 | 2007 Geo Storm

Not finding what you are looking for?
1999 Audi A4 Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audi Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

yadayada
yadayada

Level 3 Expert

61037 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

13152 Answers

Are you an Audi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...