Question about Hyundai Motor 1995 Accent

1 Answer

Reversing lights my reversing lights dont appear to be working when i put the gear lever to reverse. i have cheaked and replaced the two blubs and checked the fuses and all is ok but still doesnt work, i have heard of a reversing relay some where but not sure where to look?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 104 Answers

Could be the reverse light switch itself, usually mounted on the gearbox with 2 wires coming from it. If you had a multimeter (set to resistance / ohms) you could check that the switch changes from open to closed by disconnecting the plug on those wires and putting the multimeter across the two terminals. The resistance will be very low with the gear lever in reverse, and very high/open circuit with it not in reverse. Also check that there is battery voltage to one of the terminals.

Posted on Oct 21, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Reverse lights not working changed blubs anf fuses


it is more than likely the switch.
On the 5 speed models it is screwed into the left side of the gearbox casing next to the driveshaft inner joint and on 6 speed models it is on top of the casing.
To test the switch, disconnect the wiring connector and use a multi-meter set to resistance function, select reverse gear and test for continuity across the switch terminals. If you dont have & meter you can make up a battery bell or light set.
If your test doesnt get a response from your chosen tester then the switch is faulty, sometimes it is just stuck and a tap on the switch will clear it, however if not sorry, new switch.
I hope this helps.

Jun 19, 2014 | 2005 Renault Laguna 1.8

1 Answer

Why does the f1.9 fues blow when i shift into reverse in my 04 ford focus


You may have a faulty/shorted reverse light switch. The back-up lights come on when you put the shift lever in reverse. The shift lever linkage contacts this switch. Here is a youtube video explaining how to replace such a switch. How to fix REVERSE LIGHT SWITCH on 2005 Ford Focus and similar models...

Jun 04, 2014 | 2004 Ford Focus

1 Answer

Tail light dont work


could be a dirty socket not allowing good contact for the bulb. or you have a bad connection with one of the wires in the back of the socket.

Apr 22, 2013 | 1992 Toyota Camry V6

1 Answer

My reverse lights dont work checked fuses and bulbs all good


did you test for power to the bulbs, possibly a bad ground connection for the bulbs, or the selector lever is broken reverse sensor is usually on the trans

Apr 04, 2010 | 2004 Chevrolet Silverado 2500HD

3 Answers

My reverse lights dont work put new bulbs in but still dont work


you might have a reverse switch fault check on the box to see if it is connecting to the gear leaver when you put it in reverse..if not then that will have to be replaced, it might be the plunger in the switch broken or worn away..hope this helps

Feb 16, 2010 | 2004 Mazda 6

2 Answers

I have a 98 jeep cherokee 4L 4x4 automatic and the reverse lights dont work the bulbs are good and all fuses are too? any ideas


Reverse lamp switch wiring or switch itself is defective. Mounted on trans. Run slector lever over reverse with someone watching. the back.If yhey flicker the switch is bad. Work it several times sometimes helps .

Oct 28, 2009 | 1998 Jeep Cherokee

1 Answer

1996 Plymouth voyager reverse lights not working, transmission replaced this week and they claimed the reverse lights have nothing to do with reverse lights. owners manual does not show a fuse for back up...


They are full of baloney. Ther's a switch underneath the shift lever that engages when you shiht into reverse. The mechanic probably loosened it when reconnecting the shift linkage to the new tranny.

Thay may have knocked the switch out of position, which would cause the lights to go on in some other gear than reverse. That would be the first thing I check.

Good luck !

Marco

Jun 18, 2009 | 1997 Plymouth Voyager

3 Answers

1996 Mercedes Benz E-Class Saloon, Reversing lights not working


bulbs burned out or vehicle not recognizing reverse gear engaged at shifter-check wiring before condemning shifter assembly

Aug 07, 2008 | 2008 Mercedes-Benz Mercedes Benz E Class

2 Answers

Back up lights


Could be the mechanism inside the shifter that tells the car it's in reverse. Usually a little button of sorts.

Jul 18, 2008 | 1994 Toyota Corolla

Not finding what you are looking for?
Hyundai Motor 1995 Accent Logo

466 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

70387 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6879 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...