Question about 1992 Lexus Sc 300

1 Answer

Power Steering Where can I find a POWER STEERING PRESSURE HOSE for a reasonable price?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Elmhurst Toyota, Elmhurst IL. Ask for Curt Aigner. I wouldn't recommend putting anything but factory parts on a 17 year old Japanese sports coupe.

Posted on May 27, 2009

2 Suggested Answers

  • 1 Answer

SOURCE: Power Steering Pressure Hose

unable to loosen lower part of power steering pressure hose

Posted on Jan 11, 2009

  • 1 Answer

SOURCE: Power Steering Pressure Hose

Simple. Remove bolt from pump. Remove 2 10mm bolts that anchor it to the frame. Then disconnect it where the 2 hoses meet just behind the alternator. Takes less than 3 minutes without air tools.

Posted on May 15, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How involved is it to replace a power steering pump on a 2007 Explorer 4.0?


Power Steering Pump - 4.0L Special Tool(s) Installer Set, Teflon® Seal
211-D027 (D90P-3517-A) or equivalent Material Item Specification MERCON® V Automatic Transmission Fluid
XT-5-QM (or XT-5-QMC) (US); CXT-5-LM12 (Canada) MERCON® V
Item Part Number Description 1 388898 Teflon® seal 2 - Pressure line-to-pump fitting (part of 3A719) 3 W700839 Power steering pump bolts (3 required) 4 3A674 Power steering pump 5 W503924 Pressure line bracket-to-engine bolt 6 3691 Power steering pump supply hose 7 W503924 Power steering pump supply hose bracket bolt
Removal
NOTICE: While repairing the power steering system, care should be taken to prevent the entry of foreign material or failure of the power steering components may result.

  1. Using a suitable suction device, remove the power steering fluid from the reservoir.
  1. With the vehicle in NEUTRAL, position it on a hoist. For additional information, refer to Section 100-02.
  1. Remove the power steering pump pulley. For additional information, refer to Power Steering Pump Pulley - 4.0Lin this section.
  1. Remove the pressure line bracket-to-engine bolt.
  1. Remove the power steering pump supply hose bracket bolt.
  1. Release the power steering pump supply hose clamp and disconnect the hose.
  1. Disconnect the pressure line-to-pump fitting.
    • Remove and discard the Teflon® seal.
  1. Remove the 3 bolts and the power steering pump.
Installation
  1. NOTE:A new Teflon® seal must be installed.Using the Teflon® Seal Installer Set, install a new Teflon® seal to the pressure line fitting.
  1. Position the power steering pump and install the 3 bolts.
    • Tighten to 25 Nm (18 lb-ft).
  1. Connect the pressure line-to-pump fitting.
    • Tighten to 75 Nm (55 lb-ft).
  1. Connect the power steering pump supply hose.
  1. Install the power steering pump supply hose bracket bolt.
    • Tighten to 11 Nm (97 lb-in).
  1. Install the pressure line bracket-to-engine bolt.
    • Tighten to 11 Nm (97 lb-in).
  1. Install the power steering pump pulley. For additional information, refer to Power Steering Pump Pulley - 4.0Lin this section.
  1. Fill the power steering system. For additional information, refer to Section 211-00.

Apr 13, 2016 | Ford Cars & Trucks

1 Answer

How to change the power steering pressure hose on a 1995 Buick Regal gran sport


How to Remove a Power Steering Hose the Easy way, Tool ...

? 7:49
www.youtube.com/watch?v=OVBFrMcmV7Y
Dec 12, 2013 - Uploaded by Artistry Photography How to Remove a Power Steering Hose the Easy way, Tool Review ... The removal of this power steering pressure hose is a hard job but the ...

Replacing A Leaking Power Steering Hose - YouTube

? 2:38
www.youtube.com/watch?v=l1boEHtawcM
May 12, 2010 - Uploaded by Scotty Kilmer replace the whole hose assembly, they hold 1600 psi pressure, you can't .... i was told i need a new power steering pressure hose for my 2003 .

Oct 16, 2015 | Buick Cars & Trucks

1 Answer

How do i install power steering hose on a 1991 lexus 400


If you notice problem with power steering,the hose has to be inspected,if its faulty it has to be replaced.

=========
For your help,i provide you with few solved helplinks showing how exactly to replace power steering hose:------

How to Remove Power steering Pressure Hose ?

http://schematicsdiagram.blogspot.com/2011/12/how-to-remove-power-steering-pressure.html

---------

How to replace power steering pressure hose?

http://technoanswers.blogspot.in/2012/02/how-to-replace-power-steering-pressure.html

--------------
These will help.
Thanks.

Nov 28, 2012 | 1991 Lexus LS 400

1 Answer

HOW DO I REPLACE THE HIGH PRESSURE LINE FOR A POWER STEERING UNIT ON A 1998 MUSTANG?


Disconnect battery ground cable.
Remove engine Air Cleaner (ACL) .
Disconnect electrical connector in back of engine cooling fan motor.
Remove radiator fan shroud.
Disconnect constant control relay module harness from headlamp harness and place constant control relay module on top of engine to provide accessibility to power steering lines.
Remove wiring harness guide retaining screws and position guide aside.
Remove screw at power steering hose bracket.
Remove anti-rattle clip.
Remove plastic strap retaining tubes to power rack and pinion steering gear.
Remove power steering pressure hose at power steering pump.
Remove power steering pressure hose at power rack and pinion steering gear.
Remove power steering pressure hose from vehicle.
Reverse procedure to install new hose.
Fill and bleed power steering system.

Aug 20, 2011 | Ford Mustang Cars & Trucks

1 Answer

On a 99 Olds Alero, in the return lines of the power steering hoses, which place does the high pressure hose attach to?


RETURN TURN LINE GOES TO THE LEFT OF RACK PINION AND HIGH PRESSURE HOSE GOES TO THE RIGHT OF RACK PINION.LOOKING AT POWER STEERING PUMP HIGH PRESSURE HOSE THICK HOSE SCREWS INTO POWER STEERING PUMP.WHILE LOW PRESSURE HOSE HAS A HOSE WITH A CLAMP THE LOW PRESSURE HOSE HOOKS TO TOP OF POWER STEERING PUMP.LOW PRESSURE DONT SCREW INTO POWER STEERING PUMP IT IS HELD IN PLACE BY A HOSE SMALL CLAMP.

Jun 24, 2011 | 1999 Oldsmobile Alero

1 Answer

How to r&r powersteering pump 1998 mercury grand marquis


Hopfully this will be ALL you need Besides Pulley REMOVAL TOOL It can be Rented @ AutoZONE

REMOVAL
  1. Remove drive belt.
  2. Raise vehicle on hoist. WARNING: TURN AIR SUSPENSION SWITCH (LOCATED IN LUGGAGE COMPARTMENT) OFF TO PREVENT VEHICLE DAMAGE OR PERSONAL INJURY.
  3. Remove power steering pressure hose bracket.
  4. Disconnect electrical connector at power steering control valve actuator.
    1. Install Steering Pump Pulley Remover T69L-10300-B on the pulley hub. CAUTION: Do not apply in-and-out pressure on the power steering pump shaft. Pressure will damage the internal thrust areas.
    2. Hold the small hex-head and rotate the tool nut counterclockwise to remove the power steering pump pulley.
    3. Disconnect power steering pressure hose at power steering pump and drain fluid into a container.
    4. Disconnect power steering return hose at power steering pump and drain fluid into a container.
    5. Remove four retaining bolts and power steering pump and power steering pump pulley assembly.
    6. Remove power steering pressure switch from pump.
    INSTALLATION
    1. Position the power steering pump on the mounting bosses of engine block and install the bolts at the side of the power steering pump. Tighten to 20-30 Nm (15-22 ft. lbs.).
    2. Connect the power steering reservoir pump hose to the power steering pump and reposition the hose clamp to power steering pump inlet fitting.
    3. Replace power steering pressure hose O-ring.
    4. Install the power steering pressure hose to the power steering pump fitting. Tighten the tube nut with a tube nut wrench rather than with an open-end wrench. Tighten to 34-46 Nm (26-33 ft. lbs.). NOTE: Swivel or end play of the power steering pressure hose end is normal and does not indicate a loose fitting.
    5. Place the power steering pump pulley on the power steering pump shaft and install Power Steering Pump Pulley Replacer T91P-3A733-A. The small diameter threads on the tool should be engaged in the power steering pump shaft. CAUTION: Do not apply in and out pressure on the shaft. Pressure will damage the internal rotating group.
    6. Hold the small hex-head and rotate the tool nut clockwise to install the power steering pump pulley on the shaft. CAUTION: Do not apply in and out pressure on the shaft. Pressure will damage the internal rotating group. NOTE: The power steering pump pulley face must be flush within 0.25 mm (0.010 inch) of the end of the pump shaft.
    7. Remove the Power Steering Pump Pulley Replacer T91P-3A733-A.
    8. Remove the shipping tube nut from power steering pump housing prior to installation.
    9. Connect electrical connector to power steering control valve actuator.
    1. Install power steering pressure hose bracket.
    1. Lower the vehicle.
    2. If equipped, turn the air suspension ON.
    3. Install drive belt on the power steering pump pulley.
    4. Fill the power steering pump reservoir with Power Steering Fluid Motorcraft MERCON(r) ATF.

Oct 04, 2009 | 1998 Mercury Grand Marquis

1 Answer

Need to replace high pressure power steering hose on 2004 Monte Carlo SS. Need tips to effectively do the job myself. Tools needed, tricks to make the job easier, what not to do...etc. Thank yiou so much...


Power Steering Line/Hose: Service and Repair
Pressure Hose
Power Steering Pressure Pipe/Hose Replacement (3.8L)
Removal Procedure
1. Place a drain pan under the vehicle.
2. Remove the accessory drive belt.
3. Raise and support the vehicle. Refer to Vehicle Lifting.
4. Remove the tire and wheel assembly.
5. The power steering pressure hose is the lower hose at the power steering gear.
Remove the power steering pressure hose from the power steering gear.
6. Remove the power steering pressure hose from the power steering pump.
7. Remove the power steering pressure hose from the clamps on the power steering gear.
8. Remove the power steering pressure hose from the vehicle.
Installation Procedure
1. Install the power steering pressure hose to the vehicle.
2. Install the power steering pressure hose to the clamps on the power steering gear.
Notice: Refer to Fastener Notice in Service Precautions.
3. Install the power steering pressure hose to the power steering pump.
^ Tighten the fitting to 27 Nm (20 ft. lbs.).
4. Install the power steering pressure hose to the power steering gear.
^ Tighten the pressure hose fitting to 27 Nm (20 ft. lbs.).
5. Install the tire and wheel assembly.
6. Remove the drain pan from under the vehicle.
7. Lower the vehicle.
8. Install the accessory drive belt.
9. Fill the power steering system with power steering fluid.
10. Bleed the power steering system.
11. Inspect the power steering system for leaks.

00d203e.jpg

Sep 15, 2009 | 2004 Chevrolet Monte Carlo

2 Answers

My power steering pressure hose has a leak.


i pERSONALY WOULD REPLACE IT MYSELF EVEN WITHOUT MY 30yrs Of Experience in this Field. I have Enclosed Instructions for you to use. PLEASE dont Forget to RATE me As MOST folks DONT remember to that is how WE Get our Ratings such as GURU THANK YOU and Good Luck On The Job, Dont PAY a dime If YOU CAN > D I Y

REMOVAL PROCEDURE
  1. Remove the power steering pressure hose (2) from the power steering pump (1).
  2. Raise the vehicle on a hoist. Refer to Vehicle Lifting.
  3. Remove the front exhaust pipe, automatic transmission only. Refer to Intermediate Pipe Replacement in Exhaust System
  4. Remove the power steering pressure hose (1) from the power steering gear (3).
  5. Remove the power steering hose retainer (2).
  6. Remove the power steering pressure hose (1) from the vehicle
    1. Install the power steering pressure hose (1) to the vehicle
    2. Install the power steering hose retainers (2). NOTICE: Refer to Fastener Notice in Service Precautions.
    3. Install the power steering pressure hose (1) to the power steering gear (3). Tighten the fitting to 27 Nm (20 ft. lbs.).
    4. Install the front exhaust pipe, if removed. Refer to Intermediate Pipe Replacement in Exhaust System.
    5. Lower the vehicle.
      1. Install the power steering pressure hose (2) to the power steering pump (1). Tighten the fitting to 27 Nm (20 ft. lbs.).
      2. Bleed the power steering system. Refer to Bleeding Power Steering System in Service and Repair of Steering.

Mar 27, 2009 | 1999 Pontiac Sunfire

1 Answer

High pressure power steering hose - one or two?


Here is a pic.

[IMG]http://i253.photobucket.com/albums/hh43/chuck943/DG1690A.gif[/IMG]



1 3A674 Power Steering Pump 2 3A714 Power Steering Pressure Hose 3 3C510 Power Steering Hose Bracket 4 3N824 Power Steering Pressure Switch 5 3504 Steering Gear 6 3A713 Power Steering Return Hose (Gear to Cooler) 7 3D746 Power Steering Fluid Cooler 8 3493 Power Steering Return Hose (Cooler to Pump

Feb 23, 2009 | 1999 Ford Taurus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

125 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lexus Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Lexus Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...