Question about 2004 Nissan Frontier

1 Answer

Check engine light on

How do i clear it. i did disconnect bat. but light came back on.

Posted by on

  • jeg071391 Oct 21, 2008

    VERY HELPFULL PEOPLE ON THIS SITE. WILL COME BACK AGAIN. AAA+++++++++++

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Nissan Master
  • 71,856 Answers

You can clear it with a OBD 2 system scanner. These are avail at all parts stores these days, about $40 for a cheap basic tool.

Posted on Oct 20, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Engine won't start after battery change.


When disconnecting your battery you need to hook up an alternative power supply . Vehicles with the electronics there have now a days . Something's need to be relearned an some of the modules may not wake back up at all , unless hooked up to a factory scan tool . Battery Disconnect or Replacement Problems

Dec 18, 2015 | 2006 Buick LaCrosse

2 Answers

How to reset engine light


pull off pos bat cable for approx. 1 minute then reinstall

Nov 08, 2013 | Dodge Challenger Cars & Trucks

1 Answer

MY (CEL) HAS BEEN ON FOR 2YRS SHOWING THE SAME DTC'S PO171 & PO174 (LEAN CONDITION BANKS 1 & 2) SINCE MY TRUCK RUNS GREAT I DIDN'T STRESS ABOUT THE CEL AND CODES, UNTIL AUG OF THIS YR WHEN I HAD TO HAVE A...


I bought a code reader and use it to cancel codes (When check light is on it puts the engine in a safe mode , affecting MPG ) I drive 600+ miles a month and the codes only throw 2 or 3 times , I have become good at canceling them on the fly with no noticeable problems. Just turned 200k and still runing strong

Oct 09, 2013 | 1999 Ford Explorer

1 Answer

How do you clear the check eng.light does discoonecting the bat reset the computer modul


what vehicle ,cmon a little help here. If it's newer than 2000 the codes will not clear by disconnecting the batt.

Mar 25, 2012 | Cars & Trucks

1 Answer

How to reset all of the codes with out taking out the bat. i know there is a way just can't remember how please help me out her


Hello: If the car is a 1995 or older all you need to do is disconnect the negative battery cable for 30 seconds, but if the condition that caused the light to come on has not been corrected the light will come back on. For 1996 or newer you have to use a scan tool to clear code to turn the light off and again the condition that caused the light to come on has to be corrected or the light will come back on. For 1996 or newer you can go to auto zone, advance auto, o'riely auto parts store and they can clear code and not charge you.
When they clear the code the light will go out.

Oct 17, 2010 | Oldsmobile Intrigue Cars & Trucks

2 Answers

My 88 olds cutlass supreme FWD will not start. I have replaced the ignition module and ecm computer. I am getting fuel but no spark. The engine turns over fine.It just won't start. where do I go next?


If the engine won't start, perform a spark test as described earlier. This will narrow the problem area down considerably. If no spark occurs, check for the presence of normal battery voltage at the battery terminal (BAT) in the distributor cap. The ignition switch must be in the on position for this test. Either a voltmeter or a test light may be used for this test. Connect the test light wire to ground and the probe end at the BAT terminal at the distributor. If the light comes on, you have voltage to the distributor. If the light fails to come on, this indicates an open circuit in the ignition primary wiring leading to the distributor. In this case, you will have to check wiring continuity back to the ignition switch using a test light. If there is battery voltage at the BAT terminal, but no spark at the plugs, then the problem lies within the distributor assembly.
If the trouble has been narrowed down to the units within the distributor, the following tests can help pinpoint the defective component. An ohmmeter with both high and low ranges should be used. These tests are made with the cap assembly removed. and the battery wire disconnected. If a tachometer is connected to the TACH terminal, disconnect it before making these tests.
  1. Connect a ohmmeter between the TACH and BAT terminals in the distributor cap. The primary coil resistance should be less than 1 ohms.
  2. To check the coil secondary resistance, connect an ohmmeter between the rotor button and the BAT terminal. Note the reading. Connect the ohmmeter between the rotor button and the TACH terminal. Note the reading. The resistance in both cases should be between 6,000 and 30,000 ohms. Be sure to test between the rotor button and both the BAT and TACH terminals.
  3. Replace the coil only if the readings in Step 1 and Step 2 are infinite.

6ac17ac.gif

Nov 13, 2009 | 1988 Oldsmobile Cutlass Supreme

2 Answers

Dash board lights on grand voyager flashing when engine on. car would not start so charged bat over night. Then bought a new bat. have changed battery and still happening. Did altinator test lights dipped...


the controls always click when you change the setting as it is electronic, don't panic, but you should ask your ex as he is well up in voyager' s and the back seat not folding down properly!!!!!

Jun 20, 2009 | 2000 Chrysler Grand Voyager

2 Answers

Trac Off and Engine light stay lit


well, the first to do is an oil service to your car, after disconnect the negative battery terminal few minutes to reset

Feb 14, 2009 | 1994 Lexus Es 300

1 Answer

Check engine light on


you need to use a scanner. disconnecting the bat ground will work on most codes. it's safer to use scanner

Dec 18, 2008 | 2005 Dodge Ram 3500

1 Answer

Check engine soon light


bank 2 that means the oxygen sensor on bank 2 is defective disconnecting the battery for at least 1 minute clear the code inside the computer but it douent repair the problem you have to change the oxygen sensor on bank call the dealer they gonna tell you wish sensor it is thank you for using fixya pierre

Jun 26, 2008 | 2002 Chevrolet TrailBlazer

Not finding what you are looking for?
2004 Nissan Frontier Logo

Related Topics:

80 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

71694 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22082 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...