Question about 1992 Oldsmobile Cutlass Supreme

1 Answer

Best way to repair a starter solenoid on a 1992 Olds Cutlass Supreme

Having a hard time removing the starter solenoid on my 92 olds.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 341 Answers

Take a propane torch heat the aluminum where the screws go into starter screws will come out

Posted on Oct 21, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What makes the fuel pump not kick on on a 92 Oldsmobile Cutlass


There is a red wire close to the battery in the front. It's not connected to anything. Apply positive voltage and that will run your pump for testing purposes.

Dec 08, 2015 | Oldsmobile Cars & Trucks

1 Answer

Where is the temperature sender on a 92 Olds cutlass supreme 3.4 engine


1992 Oldsmobile Cutlass Supreme 3.4L SFI DOHC 6cyl

The Engine Temperature Sensor is located: Under hood, driver side, upper engine area, mounted on rear cylinder head

Jul 13, 2015 | Cars & Trucks

1 Answer

2008 sl awd Nissan Rogue, won't start Battery seems to have power making a clicking sound may be starter, having hard time finding starter location.


Know this problem was posted several years ago, but having same issue with my 2008 Nissan Rogue. We've tried everything short of having the battery replaced, (including charging it), and nada. So, tomorrow morning, that'll be our next move. Sucks, but best thing to die. Much rather than than an alternator, starter or solenoid.

Mar 24, 2012 | Cars & Trucks

1 Answer

92 f150 will not start? Lights do not dim but when i try to start it nothing happens.


First, assuming this is an automatic trans, Try starting it in neutral instead of park. Old fords are known for touchy neutral safety switches. If that fails, then you must locate the starter solenoid. Follow the positive battery cable. It goes directly to the solenoid. Does it click when you try to start it? If so, then probable a faulty starter. If not, then remove the small wire at the s terminal of the solenoid, and using a twelve volt test light, see if you have power there when you turn the key to the start position. I'll bet by this step you will have found your problem. If not, get back to me.I check my emails several times daily.

Mar 10, 2011 | Ford F-150 Cars & Trucks

1 Answer

Unable to remove starter on a lincoln navigator 2000


Where are you stuck?
Removal & Installation 1. Disconnect the negative battery cable. 2. Raise and safely support the vehicle. 3. Remove the starter terminal cover. 4. Remove the terminal nut and separate the battery starter cable from the starter motor. 5. Disconnect the solenoid (S) terminal connector, if equipped with a starter mounted solenoid. NOTE: To disconnect the hard-shell connector from the solenoid (S) terminal, grasp the plastic shell and pull off; do not pull on the wire. Pull straight off to prevent damage to the connector and (S) terminal. 6. Remove the starter motor retaining bolts. 7. Remove the starter motor from the vehicle. To Install: 8. Place the starter motor in position and install the starter motor retaining bolts. Tighten the bolts to 15-20 ft. lbs. (20-27 Nm). 9. Install the battery starter cable and a terminal nut to the starter motor. Tighten the terminal nuts to 79 inch lbs. (9 Nm). 10. Connect the solenoid (S) terminal connector, if equipped with a starter mounted solenoid. 11. Install the starter solenoid safety cap. If equipped. 12. Lower the vehicle. 13. Connect the negative battery cable. Start the engine several times to check starter motor operation.
Let me know how you make out..

Feb 17, 2011 | Lincoln Navigator Cars & Trucks

1 Answer

Mitsubishi nimbus 92 starer motor problem


If your starter is only clicking when you try to crank the engine, the starter solenoid is bad. You might be able to get it to start, by tapping the starter a few times and then try cranking, but it is worn internally and will continue to give the same problem until it's replaced, the entire starter or just the solenoid.

Feb 16, 2011 | Mitsubishi Minivan Cars & Trucks

Not finding what you are looking for?
1992 Oldsmobile Cutlass Supreme Logo

Related Topics:

305 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

70387 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6880 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...