Question about 2000 Oldsmobile Intrigue

1 Answer

99 Olds Intruige removing the alternator

What are the steps to remove the alternator in a 99 olds intruige

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Vice President:

    An expert whose answer gotĀ voted for 100 times.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

  • Expert
  • 185 Answers

Disconnect the + lead of the battery
Remove the wires going to the alternator. Mark them with a piece of tape so you can put them back to the same terminal.
there are probably two bolts that need to be removed. One will be fastened to a slotted strap. Removing this one will allow the alternator to pivot on the remaining bolt. This will be the one that allows the fan belt to be removed from the pulley on the alternator. Removing the 2nd will allow the alternator to be removed from the engine.
Installation of the replacement is the reverse procedure. Aftere you install the 2nd bolt, put the fan belt back in the slot and pull the alternator so the slack is taken up in the belt, then tighten the bolt

Posted on Oct 22, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Does a map sensor on a 2000 Oldsmobile intruige need a relearn? Everything else does so wondering if this does too. Thanks


No. Computer on these have to be reprogrammed if replacing. Nothing on these have a relearn procedure.

May 19, 2016 | Oldsmobile Cars & Trucks

1 Answer

99 olds cutlass blower motor resistor


remove glove box to get better access to the blower motor. resistor is located beside the blower fan motor. with glove box removed, then you will not have to stand on your head doing the job, good-day!

Jan 29, 2012 | 1999 Oldsmobile Cutlass

1 Answer

98 OLDS INTRUIGE JUST REPLACED ALTERNATOR BUT DIDNT SOLVE PROBLEM SURGES AT ACCELERATION AND WANTS TO DIE AT AN IDLE. WILL STAY RUNNING IF KEEP RPMS AT 1000 OR HIGHER


i check ur fuelinectors on heat soaked engine making sure their firing correctly and check fuel pressure at the rail from ur pump

Jul 09, 2011 | Oldsmobile Intrigue Cars & Trucks

1 Answer

How do I replace the alternator


Hello, Alternators are a car part that can be very costly to fix because of labor costs. But with an hour or two of time and a little elbow grease, you can do it yourself. And to replace the alternator follow the following steps below:

Step 1. Pull your car into the garage or your work area. Turn the car off and let it sit for a while to cool.

Step 2. Begin by disconnecting the negative cable of the battery.

Step 3. Remove the serpentine belt from the pulley on the alternator. Do this by using a socket wrench to turn the serpentine automatic belt tensioner so that it allows slack in the belt. Then simply slip the belt off the alternator pulley.

Step 4. Locate and disconnect all the mounting bolts on the alternator, use a vehicle specific manual if you have any trouble.

Step 5. Disconnect all wires attached to the alternator then remove the alternator from the car.

INSTALLING NEW ALTERNATOR.

Step 1. Slide the new alternator into place. Do not worry about the serpentine belt yet.

Step 2. Replace the bolts that held the previous alternator to secure the new one in place.

Step 3. Attach the wires to the new alternator the same way they were attached to the old one.

Step 4. Adjust the serpentine belt tensioner the same direction you did in Section One to put slack in the belt. Wrap the belt around the pulley of the new alternator and then remove the socket wrench from the automatic belt tensioner.

Step 5. Inspect the belt to be sure it is not snug and follows the path required in the pulley and belt configuration diagram.

Step 6. Hook the negative battery wire back to the negative terminal on the battery.

Thanks






























Jul 20, 2010 | 1995 Buick Skylark

1 Answer

What are the lower intake manifold bolt torque sequence on a 98 oldsmobile intruige


When torqueing bolts on manifolds or heads you always start in the middle or center and torque in a circle motion and olny torque 1 bolt at a time. Start with a low toque and increase torque up 5 to 10ft lbs / or newtons each time until torque spec is reached.

Mar 14, 2010 | 1998 Oldsmobile Intrigue

1 Answer

Do you have step by step instructions on how to change out an alternator on a 2002 Chevy S-10 with a 4.3 liter engine ( 4wd if that matters ). THANKS


Not specific to S-10 truck, but here you go.
Before you start, you might want to make a sketch, or take a couple of digital photos of alternator wiring and belt routing to make reassembly easier.
Disconnect negative (-) battery cable from battery.
Find serpentine belt tensioner pully. Should be a square hole in arm that holds that pulley. Insert a 3/8" socket wrench or breaker bar into hole to remove tension on belt.
Remove belt from alternator pulley.
Diconnect all wires from the rear of the alternator.
Remove alternator mounting bolts, make note of order and location of any nuts/washers/spacers.
Remove old alternator.
Installation is reverse of removal.

Dec 16, 2009 | 2002 Chevrolet S-10

1 Answer

To remove an alternator on a 1998-99 Intrepid, on drivers side


FIRST OF ALL.TURN OFF RADIO SO YOU WONT LOSE RADIO CODE.FOR THE 2.7L ENGINE.DISCONNECT NEGATIVE BATTERY CABLE.REMOVE THE LOWER PLASTIC SPLASH SHIELD.REMOVE TRANSMISSION COOLER AND POSITION IT ASIDE.REMOVE THE LOWER RADIATOR CROSSMEMBER SUPPORT.LOOSEN BUT DO NOT REMOVE.ADJUSTING T BOLT AND THE PIVOT BOLT.LOOSEN DRIVE BELT ADJUSTING BOLT.REMOVE OR DISCONNECT THE FOLLOWING.DRIVE BELT.REMOVE ALTERNATOR ELECTRICAL WIRES.REMOVE PIVOT BOLT CAREFUL NOT TO LOSE THE SPACER.REMOVE THE ALTERNATOR. NOW THE 3.2L AND 3.5L ENGINES REMOVE THE NEGATIVE BATTERY CABLE.THEN REMOVE THE LOWER MOUNTING BOLT AND PIVIT BOLT.REMOVE DRIVE BELTTENSION BOLT THEN DRIVE BELT.REMOVE BRACKET LOWER MOUNTING BOLT AND PIVOT BOLT.THEN REMOVE THE ALTERNATOR + ALTERNATOR FIELD CIRCUIT PLUG + ALTERNATOR B+ TERMINAL NUT AND WIRE.THEN PUT EVERYTHING BACK VISA VERSA.

Sep 18, 2009 | 1999 Dodge Intrepid

1 Answer

Changing the alternator on an 1996 olds 88


Disconnect Battery, Remove Serpintine Belt, Remove All Mounting Bolts At Alternator there should be 4 bolts 1 top ,1 bottom 2 back. Reverse procedure for Install

Mar 22, 2009 | 1996 Oldsmobile 88

Not finding what you are looking for?
2000 Oldsmobile Intrigue Logo

399 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

71162 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22059 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6992 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...