Question about Fiat X1/9

1 Answer

Cars I urgently need a workshop manual or fuel pipe layout drawings for Iveco engine 8361 SRi 25 motor used in 150 kva generator No help available here in Luanda, Angola Thanks

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

I have got a problem with my injeters i have had them all tested and its still playing up

Posted on Oct 20, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

87 f-150 4x4 5.0 no spark to distributer,no power to feul relay


Hello Kenneth Pettey,

Un-LESS you are going to buy VOLUME 3 of the
FACTORY+WORKSHOP+REPAIR+MANUAL
for your TRUCK... (which I heartily recommend)

I Went on-line to BBB Industries wiring & technical service bulletin site (see below, registration required)... and found 2 (two) perfect fusible links.. on both sides of your EEC Power Relay (fuse link "z" & fuse link "n")... That make the perfect suspects
for your described problem...

"n" = 20 ga brown
"z" = 20 ga blue...

(located immediately left of the "FUEL CUT-OFF RELAY")

Please do look at the associated drawing

A simple continuity test with ANY volt-ohm-meter ought to tell you if these fusible links are NOT intact...

Otherwise you are looking DIRECTLY at replacing & reprogramming your ECM ... California = worst case scenario.
(also shown on the drawings ... not likely)

The ECM pictures & numbers are for illustration purposes ONLY...
If you live in CALIFORNIA... it is solely & completely your responsibility to assure you are in compliance with STAE LAWS ... and regulations.... (try though they may.. the envy of the FEDERAL GOVERNMENT).

You must verify your application numbers yourself...
(check out rockauto (below)).

Hope this helps!!


1987 FORD 150 5 0L 302cid V8 Engine Control Module ECM Computer RockAuto

Engine Control Computer A1 CARDONE Reman


Drawings & Technical bulletins

BBB Industries Premium Alternators Starters Power Steering Products

Aug 21, 2016 | Cars & Trucks

2 Answers

1995 Camry fuse names and locations


you are after the fuse layout legend for the engine bay or interior

here is the whole repair manual
Toyota Camry XV10 1992 1998 Workshop Manuals Factory Service Manuals

Aug 04, 2016 | Cars & Trucks

1 Answer

Maleny historical society is restoring an old DB kero tractor, engine no AK4 33 1/2 12617, Frame no p25-18711. Believed to be 1950s model.can you help


1953-1958 david brown 25s
used this engine 2.5L 4-cyl kerosene engine 154 ci
compression 4.7:1
RPM:1600
25s also were fitted with
25D:diesel engine or 25C:petrol engine

see if any
25 D or 25 C engine repair manuals will give you the torque figures

serial number P25-18711 ?
10 year gap . no specifics
1955 start -P25 -16998
1966 start P25 - 19041

chassis number no info

May 31, 2016 | Cars & Trucks

1 Answer

Where can i get a layout drawing for coolant system ford fiesta mk6


wikiford, fordownersclub, passionpuma also search for ford manual.ru and you'll find full workshop manuals online

Jan 10, 2015 | Ford Cars & Trucks

1 Answer

Mitsubishi Workshop Manual Needed


Google it for the part of the car you want to look at or there may be one available in cd foremat from eBay

Nov 19, 2013 | Cars & Trucks

1 Answer

Looking for workshop manual for 1998 iveco eurostar primemover


come back with what engine you have as cummins and detroit have manuals to cover this topic

Jan 26, 2013 | Cars & Trucks

2 Answers

Need a motor diagram torch settings and overhaul


Hi,if you go to autozone.com and sign up for my zone(it's free).Thay have a on line free repair manual,it has everything needed to rebuild the top end of his engine and more.Hope this helps you.If it does please rate it. Thank You for using fixya.....iluv2fish.......Ray.....

Jun 24, 2010 | 2002 Chevrolet Malibu

1 Answer

How to change head gasket?on gas v6. ISUZU RODEO Vin #452CG58V554341786


This is the same for many years. I will send this in 2 post it is to long. Hope this helps you. From the '00 Rodeo workshop manual:

Cylinder Head Assembly
Removal
1. Disconnect battery ground cable.
2. Disconnect connector of intake air temperature
sensor from intake air duct.
3. Remove PCV hose from air intake duct.
4. Remove nut from air intake duct bracket and loosen
hose clamp on throttle body. Remove air intake duct
assembly with air cleaner cover.
5. Remove intake air duct bracket from cylinder head.
6. Drain engine coolant.
7. Move drive belt tensioner to loose side using wrench
then remove drive belt.
033RW001
8. Remove radiator upper hose from engine side.
9. Remove four nuts of exhaust front pipe.
10. Remove three bolts from generator bracket then
remove the generator with brackets.
065RW025
11. Disconnect crankshaft angle sensor connector.
12. Disconnect knock sensor connector.
13. Remove heater hose from adapter side.
14. Remove heater hose from water pipe side.
15. Remove water hose between water pipe and throttle
body.
16. Remove fuel pipe joint eye bolts from fuel rail
assembly and remove fuel pipe bracket with electric
ground cable.
042RW001
17. Disconnect connector for evaporation valve.
18. Remove canister hose.
19. Remove fixing nut of intake manifold stay from
cylinder block side.
025RW002
20. Remove two bolts from intake manifold for water pipe
support and remove cylinder head assembly.
21. Remove engine harness cover and disconnect three
connectors from chassis harness on left rear side
engine compartment.
22. Disconnect connector for power steering pump
pressure switch.
23. Remove four bolts and remove crankshaft pulley.
ENGINE MECHANICAL (X22SE 2.2L) 6A–23
020RW014
24. Remove two bolts and nut then remove timing belt
front cover.
25. Remove ventilation hose from cylinder block side and
from cylinder head side.
26. Remove two bolts, ignition cable cover and remove
ignition cables from spark plug.
27. Disconnect camshaft angle sensor connector.
28. Remove ten bolts and remove cylinder head cover.
29. Remove fixing bolt of timing belt tensioner then
remove timing belt tensioner.
020RW010
30. Remove timing belt.
CAUTION:
 Do not bend or twist belt, otherwise its core could
be damaged. The belt should not be bent at a
radius less than 30 mm.
 Timing belt drive gear counterhold with J–42620.
 Do not allow oil or other chemical substances to
come in contact with the belt. They will shorten
the life.
 Do not attempt to pry or stretch the belt with a
screw driver or any other tool during installation.
 Store timing belt in cool and dark place. Never
expose the belt direct sunlight or heat.
31. Remove two idle pulleys, the left side with idle pulley
bracket.
32. Remove two bolts and stud bolt and remove timing
belt rear cover.
33. Remove camshaft angle sensor
34. Disconnect engine oil pressure switch connector.
050RW005
35. Remove camshaft assembly exhaust side.
36. Use J–42623 to remove ten cylinder head fixing bolts
012RW007
6A–24 ENGINE MECHANICAL (X22SE 2.2L)
Installation
1. Put cylinder head gasket on the cylinder block.
012RW011
2. Install the cylinder head assembly, tighten cylinder
head bolts by four steps tightening method in the
following sequence to the specified torque.(use
J–42623)
Torque: 25 N·m (18 lb ft) + 90 + 90 + 90
012RW006
3. Install camshaft assembly exhaust side and tighten
camshaft bracket bolts in the sequence to the
specified torque.
Torque: 8 N·m (5.9 lb ft)
015RW014
4. Connect engine oil pressure switch connector.
5. Install camshaft angle sensor.
6. Install the timing belt rear cover and tighten three
bolts to the specified torque.
Torque
M6 bolt: 6 N·m (4.4 lb ft)
M8 bolt: 8 N·m (5.8 lb ft)
020RW012
7. Install left side idle pulley with idle pulley bracket,
tighten to the specified torque and install right side
idle pulley and tighten to the specified torque.
Torque: 25 N·m (18 lb ft)
ENGINE MECHANICAL (X22SE 2.2L) 6A–25
020RW016

Oct 09, 2009 | Isuzu Rodeo Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

366 people viewed this question

Ask a Question

Usually answered in minutes!

Top Fiat Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

yadayada
yadayada

Level 3 Expert

60792 Answers

Randy Ohler

Level 3 Expert

14093 Answers

Are you a Fiat Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...