Question about Toyota Camry

1 Answer

Hi i have some probleme with my ignition switch. Usually the steering look but this time steering free the ignition switch on look. can you help please

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 120 Answers

I suspect that your steering lock mechanism had frozen. Try taking off the steering cover and gently tap with a hammer your steering column right across the ignition switch.

Posted on Oct 20, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the procedure to changing an keyed ignition lock?


Hi there,

Removal

Disconnect the negative battery cable with the proper size wrench and place away from the battery.
Insert the key into the ignition lock cylinder and turn the key to the run position.
Remove the steering column cover on a tilt steering wheel model by pressing the upper and lower section of the cover together and pulling free from the mounting plate. Remove the steering column covers on a non tilt steering wheel model by using a Philips screwdriver and unscrewing the mounting screws.
Disconnect the electrical connector from the ignition switch by lifting up on the release tab and pulling.
Press the ignition switch actuator pin by pushing a small screw driver into the key lock cylinder, while doing this pull the ignition switch out of the ignition switch housing.

Installation

Insert the new key into the new ignition switch and turn the key to the run position. Insert the new ignition switch into the ignition switch housing. Wiggle the switch back and forth until the actuator pin mounting hole is aligned and falls into place.
Install the electrical connector back into the connector housing by pressing it in with your hands.
Place the steering column covers back onto the non tilt steering wheel and insert mounting screws. Tighten screws using a Philips screwdriver. Place the steering column covers over the tilt steering wheel and press the upper and lower portion together to snap covers back into the mounting plate.
Pull on the ignition key to ensure switch is locked into place. Turn key to the "off" position and remove the key. Insert the key and start the vehicle.

Hope these help.

Jan 28, 2011 | 1992 Ford Crown Victoria

4 Answers

Ignition switch, tumbler core.


the switch is straight in front of the driver side.




Jun 21, 2008 | 1998 Volkswagen Golf

3 Answers

How do I replace my ignition switch on my 1985 audi coupe gt?


Hi!!

The ignition switch is usually mounted to the steering column and is operated by a linkage rod.

NOTE
On column-mounted ignition switches, don't confuse the switch with the lock cylinder and keys. The ignition switch is not normally visible.
On some vehicles, the steering column support has to be removed and the column lowered to find the ignition switch. On others, the switch is accessible under the dash


5e9852e.gif
The ignition switch is operated by the key switch.

To replace the switch:
  • Remove the ignition switch wiring harness.
  • Unbolt it from its position.
  • Bolt the new switch into position.
  • Attach the witing harness.
Don't forget to rate this post!! Good Luck!!

Jul 24, 2010 | 1985 Audi GT

2 Answers

My key at times doesn't want to turn at all in the ignition, its almost like it locks and is usually even worse if my steering wheel locks when i park. i can never get it to start when this happens, only a...


The most likely source of your problem is a worn or damaged key. If you have a spare key try using it to see if the ignition turns any easier. Replacing the key cylinder would be the next likely fix, and it would typicall come with a new key as well. Sounds like the ignition switch is working properly, just that your key isn't turning like it should. Have had similar problems with my daughter's 98 Bettle, but her's was related to the steering wheel locking up when she parked against a curb stop or when her wheel was turned too much in one direction or the other when she turned the car off. If she pulled hard on the steering wheel she was able to overcome the periodic problem.

She also had problems with the "brake light switch" which when it fails will not allow the car to start. Ealier VW Beetles had a recall on this switch, free replacement by the dealers. Not sure what year your Beetle was, or if you had this problem fixed.

Jul 20, 2010 | 1998 Volkswagen Beetle

1 Answer

How do i remove ignition switch on a 1991 f150 ?


HI, follow the steps below to help with this issue.



Step 1

Disconnect the negative battery cable from the terminal on the battery. Remove the upper and lower steering column covers by unscrewing or unclipping them.

Step 2

Remove the steering wheel by lifting off the center cover, disconnecting the horn wire and removing the retaining nut and washer. Make a mark on the steering wheel spline and the wheel itself so you can line it back up precisely. Pull the steering wheel straight back to remove from the shaft.

Step 3

Take off windshield wiper and turn signal switches by pulling them off as you did the steering wheel and disconnect the wiring. Slide the spacer sleeve off of the steering column.

Step 4

Unscrew the ignition switch mounting screws. Pull out the ignition switch. Disconnect the wiring connector from back of the ignition switch. Simply loosen the tabs and pull it out.

Step 5

Insert your key into the ignition. Turn the ignition switch to the locked position. Depress the retaining pin with a small screwdriver and turn the key to the Off position to free the cylinder. Once it is free, turn the key to lock position and remove the key and key cylinder.

Step 6

Install your old key cylinder into the new ignition switch assembly. Make sure the contacts in the cylinder and assembly line up. Reattach wiring to ignition switch, slide it into place, screw in mounting screws and reassemble steering wheel and switches.



Jul 11, 2009 | 1991 Ford F150

1 Answer

Replacing the ignition switch in a 96 ford mustang cobra svt


Follow these steps carefully. this will help you achieve this replacement.



  1. Disconnect the negative battery cable from the terminal on the battery. Remove the upper and lower steering column covers by unscrewing them.

  2. Remove the steering wheel by lifting off the center cover, disconnecting the horn wire and removing the retaining nut and washer. Make a mark on the steering wheel spline and the wheel itself so you can line it back up precisely. Pull the steering wheel straight back to remove from the shaft.

  3. Take off windshield wiper and turn signal switches by pulling them off as you did the steering wheel and disconnect the wiring. Slide the spacer sleeve off of the steering column.

  4. Unscrew the ignition switch mounting screws. Pull out the ignition switch. Disconnect the wiring connector from back of the ignition switch. Simply loosen the tabs and pull it out.

  5. Insert your key into the ignition. Turn the ignition switch to the locked position. Depress the retaining pin with a small screwdriver and turn the key to the Off position to free the cylinder. Once it is free, turn the key to lock position and remove the key and key cylinder.

  6. Install your old key cylinder into the new ignition switch assembly. Make sure the contacts in the cylinder and assembly line up. Reattach wiring to ignition switch, slide it into place, screw in mounting screws and reassemble steering wheel and switches.

Jun 17, 2009 | 1996 Ford Mustang

1 Answer

1998 nissan altima gxe -ignition problem


Hi what is happening is that your turn off your car and left the wheels turned to one side and specially if your car is parke in a hill what you have to do is to force the steering wheel to the same direction of your wheels this will free up the ignition switch it is going to be hard let me tell you but it will work and this is why your shift don't work once you have the ignition switch free then your shift will work again

Apr 01, 2009 | 1997 Nissan.5 Altima

1 Answer

I want the step by step instructions to replace the ignition switch.


Hi. I've put together a guide that will help you with the replacement of this ignition switch.


Step1 Disconnect the negative battery cable from the terminal on the battery. Remove the upper and lower steering column covers by unscrewing or unclipping them. Step2 Remove the steering wheelmag-glass_10x10.gif by lifting off the center cover, disconnecting the horn wire and removing the retaining nut and washer. Make a mark on the steering wheel spline and the wheel itself so you can line it back up precisely. Pull the steering wheel straight back to remove from the shaft. Step3 Take off windshield wiper and turn signal switches by pulling them off as you did the steering wheel and disconnect the wiring. Slide the spacer sleeve off of the steering column. Step4 Unscrew the ignition switch mounting screws. Pull out the ignition switch. Disconnect the wiring connector from back of the ignition switch. Simply loosen the tabs and pull it out. Step5 Insert your key into the ignition. Turn the ignition switch to the locked position. Depress the retaining pin with a small screwdriver and turn the key to the Off position to free the cylinder. Once it is free, turn the key to lock position and remove the key and key cylinder. Step6 Install your old key cylinder into the new ignition switch assembly. Make sure the contacts in the cylinder and assembly line up. Reattach wiring to ignition switch, slide it into place, screw in mounting screws and reassemble steering wheel and switches.You have just completed the task.Good job:)


Please rate and god bless.




Mar 27, 2009 | 1994 GMC Safari

2 Answers

Ignition Switch


Hi

Ignition switches are usually located on the back of the ignition barrel and are usually accessed by removing the plastic cowelling from around the steering column.

The switch is the plastic bit on the end of the barrel with the wiring plug connected to it, and is usually held in place by one or two small screws.

Very best regards

Geordie

Jun 09, 2008 | 1991 Chevrolet C1500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

149 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

64052 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...