Question about 1995 Mercury Grand Marquis

1 Answer

1995 grand marquis ls

Hi, my silenoid/starter just went out in my 1995 grand marquis ls we'll anyway i know how to get the starter out but there are 3 bolts holding the starter/silenoid together and it is impossible to get them out tried using a 10 mm wrench and tried to remove exhaust peipe to get into the very tight area.But sti'll can't get in there.




Posted by on

  • Anonymous Nov 23, 2008

    I have the same issue with a 2001. These are definately 10mm bolt heads and there is just no clearance to reach the top bolts with a wrench or socket with standard extensions.


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert that hasĀ over 500 points.


    An expert who has answered 200 questions.

  • Expert
  • 393 Answers

I believe the hole assembly comes out in one piece by removing 2 moutning bolts (1/2 in. or 13mm)

Posted on Nov 12, 2008

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Does a 1992 Mercury Grand Marquis starter have 2 or 3 bolts?

normally a three bolt...but better to remove the original, as you will probably need to return a core anyways in most cases.

Mar 19, 2014 | 1992 Mercury Grand Marquis

1 Answer

My 1995 grand marquis will not crank at all

first of all check to make sure the engine is not locked up but placing a socket wrench on the crank shaft bolt. Try to turn it clockwise, if you can not bug it, its locked up. Second do you hear a click from the starter when you turn the ignition key, Not a click from the ign. switch. If you hear a clicking nose from the starter solenoid then more than likely you need a new starter.

Jul 22, 2012 | 1995 Mercury Grand Marquis

1 Answer

How to replace a starter on a 1996 mercury grand marquis

remove the positive and neg battery connections at the battery , ( not knowing what size motor your car has, ) fords have either a 2 or 3 bolt starter,, Located under the motor ( if you can't locate it, follow the positive battery cable down, It leads right to it ,, un-bolt the cable connections to it,, and then remove the bolts that hold the starter in place,, reverse this procedure to put the new one back in, you can look at this video to see how,,

May 24, 2011 | Mercury Grand Marquis Cars & Trucks

1 Answer

My 1995 mercury grand marquis will not start what troubleshooting steps should i take to get it running? The starter works but it wont turn over as if there is no fuel getting to the pistons how would i...

the fuel shutoff is on the right side of the trunk for a 95 marguis ls. my soundsystem tripped mine just press the red button to reset and hopefully that should help you

Dec 12, 2010 | 1995 Mercury Grand Marquis

1 Answer

How do I adjust the linkage on my 1995 Mercury Grand Marquis shifter is sloppy

The bolts loosen up on the bracket that holds the shifter shaft to the cable. Look up from the floor board and look above the steering column in the shift cable area. Wiggle the shifter and you should see the problem. Tighten the bolts with a torx bit.

Jun 14, 2010 | 1995 Mercury Grand Marquis

1 Answer

Replacing a Starter on a 1990 Mercury Grand Marquis

Disconnect the battery positive terminal. Disconnect the wire going to the start. Unbolt the 2 13mm bolts holding in the starter, one on top, one on the bottom. You may have to move the starter around a little to get it out.

Mar 15, 2010 | 1990 Mercury Grand Marquis

1 Answer

What is the tire size for a 1995 Mercury Marquis?

On Firestone's site it says for a 1995 Grand Marquis with the handling package, the tire size is P225/60R16 with or without the TPMS (tire pressure monitoring system).

For a 1995 Grand Marquis GS/LS with or without TPMS it says the tire size is P215/70R15.

The page I entered in the info is here:

Hope this helps.

Feb 16, 2010 | 1995 Mercury Grand Marquis

1 Answer

Location of starter on 1995 mecury grand marquis

on the 4.6 motor the starter is on the pass.side....3#--- 10mm head bolt retain the starter to the bell hse. top inner is tuff to get to... disconnect battery prior to removal....hope this helped...GL

Jul 06, 2009 | 1995 Mercury Grand Marquis

1 Answer

Help stuck

A 95 grand marquis has a manual lever position sensor on the side of the trans it is about $130.00 at the dealer it has two bolts holding it on and about 8 wires running into it make sure u get it lined back up

May 16, 2009 | 1995 Mercury Grand Marquis

Not finding what you are looking for?
1995 Mercury Grand Marquis Logo

Related Topics:

323 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts


Level 3 Expert

71288 Answers

Ron Lankford

Level 3 Expert

5386 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22059 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides