Question about 1993 GMC Sierra K1500

1 Answer

Gmc rear end

1993 gmc rear end rebuild

looking for instructions to disassemble and assemble


thank you

Posted by on

  • chiefseneca Oct 20, 2008

    thanks for the tips..
    if the sheep can help that would be great.
    the last time i did this was 32 yrs ago and it was on a chevy 2 wd...so i am a little rusty...
    need full descriptions

    this is a 1993 gmc sierra 4WD
    the ring and pinion are shot....



    thanks



  • ron3716 Mar 25, 2009

    I have a 1997 safari 2wd and wish for instruction disassemble and reassemble

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

This is a very tough job to take on if you are not a tech...and do not have the correct tools spisific to this job...you will need a case spreding tool,a set of outside micrometers,a magnetic base dial indicator,and your basic set of hand tools.. You must know how to read heel,toe and face,as well asbacklash and depth of mesh patterns,,,If you still want to tackle your differential yourself and pay attention to must do's of your project..re sbmitt your request to this site and ask the sheep to walk you yhroug it....

Posted on Oct 20, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to disassemble the rear end in a 2000 gmc yukon and how to remove axles


Removal & Installation To Remove:
  1. Before servicing the vehicle refer to the precautions at the beginning of this section
  2. Loosen the lug nuts on the wheel and tire assemblies but do not remove the lug nuts
  3. Raise and support the vehicle
  4. Remove or disconnect the following:
    • Wheel and tire assemblies
    • Axle lubricant into a suitable container
    • Rear driveshaft
    • Parking brake cable
    • Brake calipers
    • Shock absorbers from the axle brackets
    • Vent hose from the rear axle vent fitting
    • Nuts and the washers from the U-bolts
    • U-bolts, spring plates and spacers from the axle assembly
  5. Lower the axle assembly from the vehicle
To Install:
  1. Place the rear axle assembly under the vehicle
  2. Align the rear axle assembly with the springs then connect the spacers, spring plates and the U-bolts to the rear axle
  3. Raise the rear axle assembly into position
  4. Install or connect the following:
    • Washers and nuts to the U-bolts; Torque to: 59 lb-ft. (80 Nm) then, Torque to: 89 lb-ft. (120 Nm)
    • Vent hose to the rear axle vent fitting
    • Shock absorbers to the rear axle
    • Brake calipers (See: Brake Caliper)
    • Parking brake cable (See: Parking Brake Cable)
    • Rear driveshaft (See: Rear Driveshaft)
    Wheel lug nut tightening sequence gm_trk_sub15_wheel_lug_nut_tight_seq.gif

  5. Fill the rear axle with lubricant
  6. Bleed the brake system (See: Brake Bleeding)
  7. Install the wheel and tire assemblies
  8. Lower the vehicle to the ground
  9. Torque lug nuts as follows:
    • Single Wheel: Torque to: 140 lb-ft. (190 Nm)
    • Dual Wheel: Torque to: 175 lb-ft. (240 Nm)
  10. Road test the vehicle to check performance
prev.gif next.gif

Aug 03, 2010 | 2000 GMC Yukon XL

1 Answer

The rear end is going out,whats the easiest way to repair it?


If you have limited mechanical skills the easiest way to fix it is to find a good one in the junkyard and replace the whole rear axle. if you do your own brake jobs then you could probably do that. Otherwise you will need to take it to a shop to have the gears/bearings replaced and the rear end reset up.
Of course it all depends on what part of the rear end is going bad. Most shops will do a complete rebuild so your rear end will be like new. While some people will just replace the one item that has gone bad.
Usually when something goes bad in the rear end it contaminates and causes some collateral damage to the rest of it so a complete rebuild is recommended.

Apr 08, 2010 | 1993 Land Rover Range Rover County

1 Answer

Rear-end grinding noise in 1993 GMC Sierra 1500


your description sounds like the gears inside the the same differential you just replaced.

Oct 13, 2009 | 1993 GMC Sierra K1500

2 Answers

How do you remove engine out of a 98 gmc savana van


Older vans required you to cut the front core support and slide it out from the front end. the cross member and front end of that van should unbolt though and allow you to slide it out through the the center if the front end it disassembled. hope this helps!

Feb 27, 2009 | 1998 GMC Savana

1 Answer

GMC Rear End Rebuild


here is a great site randy sell great parts at a great price and he is a pro.
check his site and you will find even more info than you need randys
and what emissionwiz said is 100% correct i have had people bring me their trucks with rear ends that they tried to set up just by looking at tooth contact and they have ruined a new set.
follow randys instruction with the right tools and you wonnt have a problem.
good luck paul

Oct 21, 2008 | 1993 GMC Sierra K1500

1 Answer

1993 ISUZU RODEO V-6


just get on car-part.com look up starter there only 30 to 50 used this will save alot of run around trying to rebuild . disconect battery remove 2 starter bolts , drop it down and remove wires from starter be careful it they look rust use wd 40 if rusty

Aug 28, 2008 | 1993 Isuzu Rodeo

2 Answers

No overdrive or 3rd gear


transmission needs sunshell and sprag update internal repair needed

Aug 26, 2008 | 1996 GMC Suburban

Not finding what you are looking for?

Open Questions:

See all 1993 GMC Sierra K1500 Questions

Cars & Trucks Logo

308 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

71288 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22059 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...