Question about 2000 Isuzu Trooper

2 Answers

Fly wheel problem on a jeep

Changed fly wheel and ring for sensor and clutch for a isuzu trooper 00 diesel 3 litre jeep. and jeep wont start woos the fly wheel and ring for sensor have to go on in a special spot. please help if u no and how could or wood u line it up ????????

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Isuzu Master
  • 450 Answers

If its a 4JX1 diesel, yes it goes in 1 spot yet it can be bolted up in every location
put crank pulley timing mark to TDC can also check by removing cam belt top cover and check timing mark aligned up with mark at 12 O clock then flywheel has small notch in edge that must go at 6 O clock (facing down) look closely it is hard to see due to flywheel sunk into back of block.

Posted on Jul 28, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 235 Answers

Engine on TDC #1 and the cut out in the flywheel is at 6'oclock .

Posted on Jul 05, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What is crank position sensor on Isuzu trooper 2002 3tdi


What is? It tells the ECU what position the crank is in to control timing.

Feb 13, 2015 | 2002 Isuzu Trooper

Tip

3.0 diesel Isuzu wont start tip


Dip the oil and check its on the max , then put 2 litres more engine oil in the sump - this trick proves the oil pump pick up pipe welding or seal is ok or bad common fault on 3.0's

on Sep 03, 2009 | 2001 Isuzu Trooper

1 Answer

How do I locate/replace crankshaft senor on my Isuzu trooper 3 litre diesel car 2001 year .I have been told this is a big job coouls nayone advise please


Its an easy job if you can get the car up high - like on a ramp .just one plug and one bolt to do .
The sensor is behind the exhaust pipe in the clutch bell housing in line with the main oil filter .

Jun 07, 2010 | 2001 Isuzu Trooper

1 Answer

2000 isuzu trooper 3.0 dieasel


The timing ring on the black of the flywheel is moving out of range of the crankshaft position sensor when you push the clutch .
Move the sensor in a bit closer but dont let it touch the ring and have your crank end float checked by a shop .

Apr 29, 2010 | 2001 Isuzu Trooper

2 Answers

HI,I have a Trooper 1998 3.l diesel,but I have a problem with the clutch,the car will not drive,exsept very slow,do I need to change?Where can I get somthing some tell me how I shall repair this problem


You need a new clutch fitted , most likely the friction plate will be the only part needed.

You have to take the gearbox out the way to do the job .

Aug 02, 2009 | 1998 Isuzu Trooper

1 Answer

Isuzu trooper stuck in 1st gear


Likely the forks on the shift rail inside the trans are sliding on the shaft or are worn. I believe your unit needs to be removed to check this.

Apr 15, 2009 | 1999 Isuzu Trooper

1 Answer

Need torque settings for dual mass flywheel in 3.0 isuzu trooper


diesel 4JX1 engine
apply engine oil to threads
1st- 59Nm(43lb ft)
2nd- 60-90deg.
3rd- 60-90deg.

Jan 03, 2009 | 2001 Isuzu Trooper

1 Answer

Isuzu trooper problem!with a 00 3 litre diesel engine not starting


Was it lined up right as the trigger point for the sensor is important.Is the fly wheel fitted one position only that the bolt holes line up or will it fit no matter which position it bolts up Line up the flywheel trigger with the sensor after you have put the engine to Top Dead Centre.Put at tdc and see if the trigger and sensor are together.

Oct 18, 2008 | 2000 Isuzu Trooper

2 Answers

Isuzu trooper 3 litre diesell oo year!


with no1 at TDC mark is on balancer and can take off top cam belt cover to check that cam gear is timmed on mark at 12 O clock there is notch in edge of flywheel that should be put at 6 O clock (facing down) it is hard to see with flywheel on engine look closely

Oct 18, 2008 | 2000 Isuzu Trooper

Not finding what you are looking for?
2000 Isuzu Trooper Logo

541 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

70374 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...