- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
if their metal, the could be coming from transmission fluid lines, are they going into radiator ? one @ top & one @ bottom of rad . their cooling lines from trans, supply / return . if rubber lines, they go to a transmission cooler , looks like a small radiator, rectangular , supply / return. power steering has no cooling . these lines don't come from engine, power steering has power steering fluid NOT TO BE MISTAKEN FOR TRANSMISSION FLUID, TOTALLY DIFFERANT !!!!!!
The pad drums of your 2000 Dodge Grand Caravan can wear with use. Heat buildup in the brakes can glaze, warp or crack the drum. If that happens, replacement of the drum is the only way to fix it. In most cases, you can remove the rear drums, replace them with a new set and leave the existing shoes on the van. Take a minute and inspect the brake shoes thoroughly while you have the drums off the van.
Loosen the lug nuts on the rear of your 2000 Dodge Grand Caravan with a lug wrench. Do not take them off the wheel studs.
Raise the rear of the van with a jack and support it on a set of jack stands. Place the stands under the rear suspension, making sure they are secure. Remove the lug nuts from the wheel studs and pull off the rear wheels.
Check the rear drum where the wheel studs come through for retaining clips. These are used during the manufacturing process; and if they are still on your van, they need to be removed. Pry the clip off the wheel stud with a flat head screwdriver and discard them. Most vehicles will have two clips on each brake drum.
Grasp the brake drum on the outer edges and pull it straight off the wheel studs and brake pads. Discard the old drum and slide the new drum into place, aligning the holes in the drum with the wheel studs. Push the drum in until it seats completely. Repeat the process on the opposite side of the van.
Position the wheel back on the wheel studs and install the lug nuts by hand. Raise the back of the van with a jack and remove the jack stands from under the suspension. Lower the van to the ground and tighten the lug nuts with a lug wrench.
oooooh not easy if you do not have the spanner wrench the releases the tensioner you can get one in an autoparts store or rent one if it is not something you will use often Advance auto parts ,and auto zone lend them out once you have the wrench you take a good look at the old one and if needed remove the tire on that side of the van for better access take a picture so you remember how it goes and remove replace you might need someone to give you a hand for this
Looking at the engine from front (right side of the Van): Stating at the Top, Going Left to Right and Clockwise:
Over the Alternator
To under the Idle Pulley,
To Over the AC Compressor.
To the Left Side of the Water Pump.
To the Right side and Under the Crankshaft Pulley
To the Right side and Over and Down the Tensioner
To Under the Power Steering Pump
And Back up-to the Left side of the Alternator.
Advise when puting it on:
Put the Belt around everything else accept for the Alternator. After it is around all the rest of the Pulleys - Pull the belt up - tight from the Power steering Pump and the Idle Pulley to form a loop, holding the Belt close to the Altenator Pulley.
Using the 15mm wrench or belt tensioner bar - rotate the Tensioner Pulley towards the front of the Van and then place the belt over the Alternator.
Let me know if this helped or if you have additional information or questions. Feel free to contact me at FixYa.com!
Jack up pass side.Put cardboard, BIG piece under engine just in case. Using a pan to drain the oil in put under oil pan drain plug. Remove drain plug with socket wrench. Let drain 5 min. Check the gasket on the drain plug, if bad replace with new gasket .99 cents to replace gasket only on plug. Put plug back in DO NOT OVER TIGHTEN the plug. Slide drain pan with drained oil to the front to remove oil filter. Using a filter wrench remove oil filter. Let drain. When installing new filter put a little new engine oil on the rubber gasket on the filter with your finger. Screw filter back on tighten with filter wrench. Fill van with oil from front valve cover opening.